Engineering Commons^™

The Toyota Production System (Tps) In A Non-Traditional Manufacturing Environment: The Role Of Standardization In The Fast-Food Industry, Kevin Mccracken

Theses and Dissertations--Manufacturing Systems Engineering

The Toyota Production System (TPS), also known as Lean Manufacturing (LM), was founded in the automotive industry and has contributed to Toyota’s decades of success. This has brought much attention to TPS and how this system may be implemented in other industries. Focusing on the TPS foundational element of standardization, this study examines the impact of target cycle time (TCT) on process fluctuation in a fast-food environment. In order to observe the effects of TCT, team members within 3 production lines were timed. Times were measured before and after the addition of a TCT to the Standardized Work (STW) in …

Numerical Analyses And Integration Of Split Lot Sizing Using Lean Benchmark Model For Small Lot Manufacturing In High Mix Low Volume Production, Omkar Bhosale

Theses and Dissertations--Manufacturing Systems Engineering

As the global demand for automobiles has increased rapidly over the last fifty years, customers have become more particular about the characteristics of the autos they want. This change in demand, in part has pushed manufacturing to become more flexible and created a demand for alternative, more efficient processes like the High Mix Low Volume (HMLV) production of vehicles. During HMLV, manufacturers create production lot sizes and schedule to synchronize the production processes to meet customer demand on time. The demand for the automobile parts may not be uniform or parts may not be consumed by the customer immediately, Due …

Investigation Of Chip-Form And Tool-Wear In Turning Of Hardened Af9628 Alloy Under Various Cooling And Lubrication Conditions, Jason Wolf

Theses and Dissertations--Manufacturing Systems Engineering

Next generation defense and commercial applications for structural steels require new alloys that eliminate or reduce critical elements from their composition to lower cost and improve manufacturability, while maintaining or exceeding high strength and toughness requirements. A new alloy, denoted as AF9628, has recently been developed for this purpose and its manufacturing characteristics and the material response in component manufacturing must be fully understood.

In the present study, hardened AF9628 alloy was turned with a coated carbide cutting tool under fixed cutting speed, feed rate, and depth of cut parameters. This work focuses on chip-form and tool-wear analysis to understand, …

An Analysis Of Resistance Spot Weld Quality Based On Acoustic And Electrical Signatures, Ivan Charles Butler

Theses and Dissertations--Manufacturing Systems Engineering

The union of a set of materials by way of Resistance Spot Welding is designed so that once fused together, a substantial amount of intentional, external force must be applied to separate the contents. Therefore, Resistance Spot Welding is often the preferred fusion method in high-volume manufacturing processes. The result of Resistance Spot Welding however is the formation of a weld nugget which is not visible to the naked eye. Destructive and/or ultrasonic methods applied off-line must be used to determine the quality of each weld; both inefficient and expensive processes. The following research analyzes the data fed back during …

Implementation And Analysis Of True Lean In A Startup Company By Using Pdca Model, A Case Study In A Manufacturing Venture, Ankit Jangid

Theses and Dissertations--Manufacturing Systems Engineering

The purpose of this research is to implement and analyze the true lean transformation in a manufacturing start-up organization. Often, lean transformations are observed in developed manufacturing organizations having sophisticated production lines and numerous employees, where lean tools are utilized to reduce waste while increasing profit. However, this type of transformation is narrowly focused on quantifiable process results and falls short of the ultimate goal, establishing a true lean culture within the organization. As a result, it is recommended that true lean principles, philosophies, culture, operations environment and tools be applied at the very beginning stages of an organization, or …

Alternate Models For Natural Gas Transportation System Performance Optimization, Gnana Shekaran Arumugam

Theses and Dissertations--Manufacturing Systems Engineering

The Natural Gas market in the U.S is growing rapidly with evidence that the nation has enough shale reserves to power the country for the next century. To ensure continued economic benefits through the use of this environmentally desired energy source, it becomes important to optimize the transportation network system design. Transportation through pipelines is one of the most common methods used to distribute Natural Gas from source to destination. This transportation system, consisting of pipelines, compressors and other supporting equipment, must be optimized, considering all relevant parameters to minimize cost and increase profit. The research presented here improves on …

A Study Of Queuing Theory In Low To High Rework Environments With Process Availability, Adam J. Brown

Theses and Dissertations--Manufacturing Systems Engineering

In manufacturing systems subject to machine and operator resource constraints the effects of rework can be profound. High levels of rework burden the resources unnecessarily and as the utilization of these resources increases the expected queuing time of work in process increases exponentially. Queuing models can help managers to understand and control the effects of rework, but often this tool is overlooked in part because of concerns over accuracy in complex environments and/or the need for limiting assumptions. One aim of this work is to increase understanding of system variables on the accuracy of simple queuing models. A queuing model …

Achieving Ultrafine Grains In Mg Az31b-O Alloy By Cryogenic Friction Stir Processing And Machining, Anwaruddin Mohammed

Theses and Dissertations--Manufacturing Systems Engineering

This thesis presents results from the application of cryogenic cooling on multiple-pass friction stir processing and the subsequent orthogonal machining on friction stir processed and as-received Mg AZ31B-O disks, and shows their combined effects on microstructure and microhardness values. A simple friction stir tool, a specially designed fixture and liquid nitrogen are used to perform multiple-pass friction stir processing experiments on Mg AZ31B-O alloy. The friction stir processed and as-received sheets are then made into disks for the orthogonal machining experiments. This study analyzes the microhardness, microstructure changes by cryogenic friction stir processing and the effect of machining conditions such …