Open Access. Powered by Scholars. Published by Universities.®
- Publication
- Publication Type
Articles 1 - 8 of 8
Full-Text Articles in Engineering
Development Of A 3d Printed Conductive Biopolymer For Cardiac Tissue Engineering, Britanny Lizeth Stark
Development Of A 3d Printed Conductive Biopolymer For Cardiac Tissue Engineering, Britanny Lizeth Stark
Open Access Theses & Dissertations
Cardiovascular disease (CVD) is the leading cause of death in the US, with approximately 859,000 deaths each year. The major contributor to CVD is Acute Myocardial Infarction (AMI), which causes the death of approximately 25% of the cardiomyocytes present in the left ventricle of the heart. After AMI, the adult human heart has a very limited regenerative capacity. Moreover, the electrical propagation of the myocardium is severely disrupted, making the heart more susceptible to failure and patient death. However, current pharmacological treatments do not address the loss of cardiomyocytes and the disruption of electrical propagation in the heart. Tissue engineering …
Anisotropic Scaffolds For Peripheral Nerve And Spinal Cord Regeneration, Wen Xue, Wen Shi, Yunfan Kong, Mitchell Kuss, Bin Duan
Anisotropic Scaffolds For Peripheral Nerve And Spinal Cord Regeneration, Wen Xue, Wen Shi, Yunfan Kong, Mitchell Kuss, Bin Duan
Department of Mechanical and Materials Engineering: Faculty Publications
The treatment of long-gap (>10 mm) peripheral nerve injury (PNI) and spinal cord injury (SCI) remains a continuous challenge due to limited native tissue regeneration capabilities. The current clinical strategy of using autografts for PNI suffers from a source shortage, while the pharmacological treatment for SCI presents dissatisfactory results. Tissue engineering, as an alternative, is a promising approach for regenerating peripheral nerves and spinal cords. Through providing a beneficial environment, a scaffold is the primary element in tissue engineering. In particular, scaffolds with anisotropic structures resembling the native extracellular matrix (ECM) can effectively guide neural outgrowth and reconnection. In …
3d Printing Of Multilayered Scaffolds For Rotator Cuff Tendon Regeneration, Xiping Jiang, Shaohua Wu, Mitchell Kuss, Yunfan Kong, Wen Shi, Philipp N. Streubel, Tieshi Li, Bin Duan
3d Printing Of Multilayered Scaffolds For Rotator Cuff Tendon Regeneration, Xiping Jiang, Shaohua Wu, Mitchell Kuss, Yunfan Kong, Wen Shi, Philipp N. Streubel, Tieshi Li, Bin Duan
Department of Mechanical and Materials Engineering: Faculty Publications
Repairing massive rotator cuff tendon defects remains a challenge due to the high retear rate after surgical intervention. 3D printing has emerged as a promising technique that enables the fabrication of engineered tissues with heterogeneous structures and mechanical properties, as well as controllable microenvironments for tendon regeneration. In this study, we developed a new strategy for rotator cuff tendon repair by combining a 3D printed scaffold of polylactic-co-glycolic acid (PLGA) with cell-laden collagen-fibrin hydrogels. We designed and fabricated two types of scaffolds: one featuring a separate layer-by-layer structure and another with a tri-layered structure as a whole. Uniaxial tensile tests …
3d Printing Of Silk Fibroin-Based Hybrid Scaffold Treated With Platelet Rich Plasma For Bone Tissue Engineering, Liang Wei, Shaohua Wu, Mitchell Kuss, Xiping Jiang, Runjun Sun, Reid Patrick, Xiaohong Qin, Bin Duan
3d Printing Of Silk Fibroin-Based Hybrid Scaffold Treated With Platelet Rich Plasma For Bone Tissue Engineering, Liang Wei, Shaohua Wu, Mitchell Kuss, Xiping Jiang, Runjun Sun, Reid Patrick, Xiaohong Qin, Bin Duan
Department of Mechanical and Materials Engineering: Faculty Publications
3D printing/bioprinting are promising techniques to fabricate scaffolds with well controlled and patient-specific structures and architectures for bone tissue engineering. In this study, we developed a composite bioink consisting of silk fibroin (SF), gelatin (GEL), hyaluronic acid (HA), and tricalcium phosphate (TCP) and 3D bioprinted the silk fibroin-based hybrid scaffolds. The 3D bioprinted scaffolds with dual crosslinking were further treated with human platelet-rich plasma (PRP) to generate PRP coated scaffolds. Live/Dead and MTT assays demonstrated that PRP treatment could obviously promote the cell growth and proliferation of human adipose derived mesenchymal stem cells (HADMSC). In addition, the treatment of PRP …
Exploration And Optimization Of Biomaterials And Cells Required For The Fabrication Of A "Cardiac Patch", Shweta Anil Kumar
Exploration And Optimization Of Biomaterials And Cells Required For The Fabrication Of A "Cardiac Patch", Shweta Anil Kumar
Open Access Theses & Dissertations
Cardiac failure induced by myocardial infarction is believed to be one of the primary causes of morbidity and mortality all over the world. Affecting more than 26 million people worldwide, its prevalence has been observed to increase steadily. Myocardial infarction, which intitially begins as the occlusion of of a coronary artery, results in the death of millions of cardiomyocytes by obstructing blood flow to the serviced regions of the myocardium. The dead myocardium is replaced by a dense,collagenous scar which reduces the contractility of the heart, gradually leading to heart attacks. Most of the existing treatment therapies are palliative in …
Visible Light Crosslinkable Human Hair Keratin Hydrogels, Kan Yue, Yanhui Liu, Batzaya Byambaa, Vaishali Singh, Wanjun Liu, Xiuyu Li, Yunxia Sun, Yu Shrike Zhang, Ali Tamayol, Peihua Zhang, Kee Woei Ng, Nasim Annabi, Ali Khademhosseini
Visible Light Crosslinkable Human Hair Keratin Hydrogels, Kan Yue, Yanhui Liu, Batzaya Byambaa, Vaishali Singh, Wanjun Liu, Xiuyu Li, Yunxia Sun, Yu Shrike Zhang, Ali Tamayol, Peihua Zhang, Kee Woei Ng, Nasim Annabi, Ali Khademhosseini
Department of Mechanical and Materials Engineering: Faculty Publications
Keratins extracted from human hair have emerged as a promising biomaterial for various biomedical applications, partly due to their wide availability, low cost, minimal immune response, and the potential to engineer autologous tissue constructs. However, the fabrication of keratin-based scaffolds typically relies on limited crosslinking mechanisms, such as via physical interactions or disulfide bond formation, which are time-consuming and result in relatively poor mechanical strength and stability. Here, we report the preparation of photocrosslinkable keratin-polyethylene glycol (PEG) hydrogels via the thiol-norbornene “click” reaction, which can be formed within one minute upon irradiation of visible light. The resulting keratin-PEG hydrogels showed …
Bioink Properties Before, During And After 3d Bioprinting, Katja Hölzl, Shengmao Lin, Liesbeth Tytgat, Sandra Van Vlierberghe, Linxia Gu, Aleksandr Ovsianikov
Bioink Properties Before, During And After 3d Bioprinting, Katja Hölzl, Shengmao Lin, Liesbeth Tytgat, Sandra Van Vlierberghe, Linxia Gu, Aleksandr Ovsianikov
Department of Mechanical and Materials Engineering: Faculty Publications
Bioprinting is a process based on additive manufacturing from materials containing living cells. These materials, often referred to as bioink, are based on cytocompatible hydrogel precursor formulations, which gel in a manner compatible with different bioprinting approaches. The bioink properties before, during and after gelation are essential for its printability, comprising such features as achievable structural resolution, shape fidelity and cell survival. However, it is the final properties of the matured bioprinted tissue construct that are crucial for the end application. During tissue formation these properties are influenced by the amount of cells present in the construct, their proliferation, migration …
Bioink Properties Before, During And After 3d Bioprinting, Katja Holzl, Shengmao Lin, Liesbeth Tytgat, Sandra Van Vlierberghe, Linxia Gu, Aleksandr Ovsianikov
Bioink Properties Before, During And After 3d Bioprinting, Katja Holzl, Shengmao Lin, Liesbeth Tytgat, Sandra Van Vlierberghe, Linxia Gu, Aleksandr Ovsianikov
Department of Mechanical and Materials Engineering: Faculty Publications
Bioprinting is a process based on additive manufacturing from materials containing living cells. These materials, often referred to as bioink, are based on cytocompatible hydrogel precursor formulations, which gel in a manner compatible with different bioprinting approaches. The bioink properties before, during and after gelation are essential for its printability, comprising such features as achievable structural resolution, shape fidelity and cell survival. However, it is the final properties of the matured bioprinted tissue construct that are crucial for the end application. During tissue formation these properties are influenced by the amount of cells present in the construct, their proliferation, migration …