Engineering Commons^™

Adhesion And Deformation Mechanisms Of Polydopamine And Polytetrafluoroethylene: A Multiscale Computational Study, Matthew Brownell

Graduate Theses and Dissertations

Polydopamine (PDA) has been shown to bond via covalent bonding, van der Waals forces, and hydrogen bonding and is known to adhere strongly to almost any material. The application of PDA between a substrate and a PTFE surface coating has resulted in low friction and a greatly reduced wear rate. Previous research probing the capabilities and limitations of PDA/PTFE films have studied the wear and mechanical properties of the film, but the overall adhesive and deformation mechanisms remain unclear.

In this research, we investigate the tribological properties of PDA and PTFE molecules and composites from the atomic to the microscale …

Rubber Plunger Surface Texturing For Friction Reduction In Medical Syringes, Haytam Kasem, Harel Shriki, Lihi Ganon, Michael Mizrahi, Kareem Abd-Rbo, Abraham J. Domb

Friction

Friction is a genuine issue in the use of many medical devices involving rubbery materials such as plungers in medical syringes. This paper presents a new direction for the reduction of friction in medical syringes based on surface texturing of the rubber plunger. The specimens were prepared by casting poly(vinylsiloxane) (PVS) rubber into a pre-fabricated negative template obtained by 3D printing. Friction tests were performed on a home-made test-rig. It was clearly shown that friction resistance can be considerably manipulated when using textured plungers.

Friction And Wear Behaviors Of Mos2-Multi-Walled-Carbon-Nanotube Hybrid Reinforced Polyurethane Composite Coating, Zhaozhu Zhang, Mingming Yang, Junya Yuan, Fang Guo, Xuehu Men

Friction

MoS2-multi-walled-carbon-nanotube (MWCNT) hybrids containing two-dimensional MoS2 and one-dimensional MWCNTs were synthesized through a one-step hydrothermal reaction. X-ray-diffraction and transmission-electron-microscopy results demonstrated that MoS2 nanosheets were successfully synthesized, and uniformly anchored on the MWCNTs' surfaces. Furthermore, the effects of the MoS2-MWCNT hybrids on the tribological performances of polyurethane composite coatings were investigated using a UMT-2MT tribo-tester. Friction and wear test results revealed that the friction coefficient and wear rate of a 3 wt% MoS2-MWCNT-1 filled polyurethane composite coating were reduced by 25.6% and 65.5%, respectively. The outstanding tribological performance of the MoS2-MWCNT-1 reinforced polyurethane composite coating was attributed to the excellent …

Friction Predication On Pin-To-Plate Interface Of Ptfe Material And Steel, Zhuming Bi, Donald W. Mueller

Friction

In this paper, the friction behavior at a pin-to-plate interface is investigated. The pin and plate are made of Polytetrafluoroethylene (PTFE) and steel, respectively, and there is a reciprocating motion at the interface. Governing mathematical models for the relations of design variables and frictions are investigated, and a general procedure is proposed to solve the developed models and predict the friction forces at the interface subjected to given test conditions. Novel models have been developed to represent intrigued friction behaviors affected by various factors such as pin geometrics and finishes, lubrication conditions, and reciprocating speed. The test data from experiments …

Water-Based Superlubricity In Vacuum, Chen Xiao, Jinjin Li, Lei Chen, Chenhui Zhang, Ningning Zhou, Tao Qing, Linmao Qian, Jiyang Zhang, Jianbin Luo

Friction

This study achieved water-based superlubricity with the lubrication of H3PO4 solution in vacuum (highest vacuum degree <10-4 torr) for the first time by performing a pre-running process in air before running in vacuum. The stable water-based superlubricity was sustainable in vacuum (0.02 torr) for 14 h until the test was stopped by the user for non-experimental factor. A further analysis suggested that the superlubricity may be attributed to the phosphoric acid-water network formed in air, which can efficiently lock water molecules in the liquid lubricating film even in vacuum owing to the strong hydrogen bond interaction. Such capability to lock water is strongly affected by the strength of hydrogen bond and environmental conditions. The realization of water-based superlubricity with H3PO4 solution in vacuum can lead to its application in space environment.

Detailed Finite Element Analysis And Preliminary Study Of The Effects Of Friction And Fastener Pre-Tension On The Mechanical Behavior Of Fastened Built-Up Members, Francisco Javier Bonachera Martin

Open Access Theses

The characterization of fatigue resistance is one of the main concerns in structural engineering, a concern that is particularly important in the evaluation of existing bridge members designed or erected before the development of fatigue design provisions. The ability of a structural member to develop alternate load paths after the failure of a component is known as member-level or internal redundancy. In fastened built-up members, these alternate load paths are affected by the combination of fastener pre-tension and friction between the structural member components in contact. In this study, a finite element methodology to model and analyze riveted and bolted …

Identification Of Multiple Oscillation States Of Carbon Nanotube Tipped Cantilevers Interacting With Surfaces In Dynamic Atomic Force Microscopy, Mark Strus, Arvind Raman

Birck and NCN Publications

Carbon nanotubes (CNTs) have gained increased interest in dynamic atomic force microscopy (dAFM) as sharp, flexible, conducting, nonreactive tips for high-resolution imaging, oxidation lithography, and electrostatic force microscopy. By means of theory and experiments we lay out a map of several distinct tapping mode AFM oscillation states for CNT tipped AFM cantilevers: namely, noncontact attractive regime oscillation, intermittent contact with CNT slipping or pinning, or permanent contact with the CNT in point or line contact with the surface while the cantilever oscillates with large amplitude. Each state represents fundamentally different origins of CNT-surface interactions, CNT tip-substrate dissipation, and phase contrast …

Wear Analysis Of Cu-Al Coating On Ti-6al-4v Under Fretting, Karl N. Murray

Theses and Dissertations

The effects of changes in the coefficient of friction (CoF) between the contacting surfaces on the fretting wear characteristics of Cu-Al coating on Ti-6Al-4V were investigated. This Cu-Al coating is part of a system that is applied to titanium turbine blades to reduce fretting at the interface. In the application, there is a solid lubricant that is added on top of the coating as an assembly aid and to help reduce the friction while the lubricant remains within the contact. Previous studies have researched the characteristics of the coating without the additional lubricant. In this study, liquid motor oil was …

Analysis Of Computational Methods For The Treatment Of Material Interfaces, Minh C. Nguyen

Theses and Dissertations

Rocket sled tests at the Air Force Research Laboratory's Holloman High Speed Test Track frequently approach velocities where gouging development becomes the limiting factor to achieving higher operating velocities. Direct observation of the gouging process is not possible so computational modeling is necessary to study the phenomenon. Since gouging development is dependent on the impact surface conditions, the method used to model material interfaces directly affects the accuracy of the solution. Three methods are available in the hydrocode CTH to handle material interfaces: 1) materials are joined at the interface, 2) a frictionless slide line is inserted, and 3) a …