Engineering Commons^™

Editorial For The Special Issue On Micromachines For Non-Newtonian Microfluidics, Lanju Mei, Shizhi Qian

Mechanical & Aerospace Engineering Faculty Publications

In lieu of an abstract, this is an excerpt from the first page.

Microfluidics has seen a remarkable growth over the past few decades, with its extensive applications in engineering, medicine, biology, chemistry, etc [...]

Thermal Contact Resistance Measurement And Related Uncertainties, Amanda Elizabeth Stark

Mechanical & Aerospace Engineering Theses & Dissertations

Thermal contact resistance is an important parameter in detailed thermal analysis and design of aerospace systems. The ability to determine thermal contact resistance reliably can have a significant impact on the fidelity of thermal models—particularly for space applications. The 2004 NASA Langley Research Center thermal contact resistance test apparatus has been employed to evaluate two methods for inferring estimated interface surface temperatures so that thermal contact resistance can be calculated more accurately. The traditional method of extrapolation is a steady-state approach, while the new method utilizes inverse heat transfer techniques to account for inherent unsteadiness in these quasi-steady-state measurements. The …

Energy Conservation And Heat Transfer Enhancement For Mixed Convection On The Vertical Galvanizing Furnace, Dan Mei, Yuzheng Zhu, Xuemei Xu, Futang Xing

Mechanical & Aerospace Engineering Faculty Publications

The alloying temperature is an important parameter that affects the properties of galvanized products. The objective of this study is to explore the mechanism of conjugate mixed convection in the vertical galvanizing furnace and propose a novel energy conservation method to improve the soaking zone temperature based on the flow pattern and heat transfer characteristics. Herein, the present study applied the k-ε two-equation turbulence model to enclose the Navier-Stokes fluid dynamic and energy conservation equations, and the temperature distributions of the steel plate and air-flow field in the furnace were obtained for six Richardson numbers between 1.91 ⋅ 10^{5 …}

Numerical Study On The Dynamic Process Of Single Plume Flow In Thermal Convection With Polymers, Jian-Ping Cheng, Wei-Hua Cai, Hong-Na Zhang, Feng-Chen Li, Lian Shen, Shi-Zhi Qian

Mechanical & Aerospace Engineering Faculty Publications

A direct numerical simulation of single plume flow in thermal convection with polymers was carried out in a domain with 1:3 as the width to height ratio. The heat transport ability is weakened by adding polymers within the here-investigated governing parameter range. However, it is promoted when the maximum polymer extension L is increased. The distribution of vertical velocity and temperature indicates that the plume in the polymer solution case is speeded up and widens bigger as compared to that in the Newtonian fluid case. Inside the plume, polymer chains tend to release energy at the position where the …

Thermo-Mechanical System Identification Of A Shape Memory Alloy Actuated Mechanism, Cody Alexander Wright

Mechanical & Aerospace Engineering Theses & Dissertations

Shape memory alloy (SMA) actuators paired in an antagonistic arrangement can be used to produce mechanisms that replicate human biomechanics. To investigate this proposal, the biomechanical articulation of the elbow by means of the biceps brachii muscle is compared with that of a SMA actuated arm. This is accomplished by parametric analysis of a crank-slider kinematic mechanism actuated, first, with an experimentally characterized SMA wire and then an idealized musculotendon actuator based on actuation properties of muscles published in the literature. Next, equations of motion for the system dynamics of the SMA actuated mechanism are derived and phase portrait analysis …

Laminar And Turbulent Natural Convection Heat Transfer In Trombe Wall Channels, Tony D. T. Chen

Mechanical & Aerospace Engineering Theses & Dissertations

The natural convective heat transfer and air movement in a Trombe wall solar passive system has been studied analytically and numerically. Three Trombe wall channel geometries including the parallel channel with axial inlet and exit, parallel channel with side vents and Trombe wall channel coupled to the room have been considered. Several models representing these Trombe wall geometries have been formulated. For the parallel channel with axial inlet and exit geometry, a momentum-integral method has been used to solve parabolic governing equations for two-dimensional laminar flow. This formulation leads to a second order ordinary differential equation for pressure defect in …