Engineering Commons^™

Local Stresses On Lateral Pipe-Nozzle With 45 Degree Angle Intersection, James Jin Xu

Dissertations

This dissertation presents a comprehensive study of local stresses, due to internal pressure around a pipe-nozzle with 45 degree angle intersection_ The resulting circumferential and longitudinal stresses on the pipe around the pipe-nozzle region are normalized as local stress factors and plotted as function of beta, β, (the radius of the nozzle/the radius of the pipe) and gamma, y, (the radius of the pipe/the thickness of the pipe) through the finite element method. The range of beta, [3, is from 0.1, to 1.0, and gamma, y, from 10 to 300. Comprehensive studies were made for the boundary parameters, such as …

Experimental And Analytical Investigation Of Waterjet Cleaning Process, Ping Meng

Dissertations

This doctoral dissertation is concerned with the development of water based cleaning technology required by industry which may substitute the traditional approach based upon the use of various chemical cleansers.

The experimental study involves the waterjet removal of various coatings (rust, oil and epoxy based paints, etc.). Cleaning was carried out under a wide range of operational and geometrical conditions (standoff distance, travel speed, water pressure, diameters of sapphire nozzle and focusing tube, nozzle body type). A new designed spiral nozzle body was tested in this work. The use of surfactant was also investigated. Microscope and SEM surface were used …

Experimental And Numerical Investigation Of Abrasive Waterjet Polishing Technology, Fenggang Li

Dissertations

The objective of this investigation is the development of the abrasive waterjet (AWJ) based polishing technology. The result of the investigation will assist the implementation of AWJ polishing for manufacturing processes and procedures.

Experimental exploration of AWl polishing involving processing of difficultmachine materials such as Alumina ceramic and stainless steel. Surface improvement due to this processing is evaluated by measuring the roughness of the generated surfaces and examining the microhardness and micro-topography of the surfaces using Scanning Electronic Microscopy (SEM). The surface roughness of 0.3 micron was obtained at samples of ceramic and metal alloys at a reasonable rate using …

Global Fuzzy Control Based On Cell Mapping, Tea-Quin Kim

Dissertations

Cell mapping methods can generate global optimal controls for nonlinear dynamic systems. However, the implementation of this approach for on-line control is difficult due to its use of a table-based controller which requires a large amount of memory.

In this dissertation, a cell mapping based systematic method is developed to construct a fuzzy controller to replace the table-based controller for global optimal control of dynamic systems. The method consists of four steps: 1) An optimal control table is generated using a cell mapping algorithm. 2) The cells are linked into trajectories to characterize the optimal dynamic evolution of various cell. …

Reduction Of Inertia-Induced Forces In A General Spatial Mechanism, Sahidur Rahman

Dissertations

A computer-aided design procedure has been developed for minimizing the adverse effects of the inertia-induced forces by optimum mass redistribution amongst the links of high speed general spatial linkages. The evaluation of an optimality criterion for the mass redistribution of the mechanism will be carried out with the aid of a quadratic programming technique. This has been found to be successful in minimizing inertia induced forces and torques. The validity of the optimization procedure will be demonstrated by application to one kind of spatial linkage.

No literature has been found on the balancing of a general spatial mechanism, since its …

Real Time Control Of Nonlinear Dynamic Systems Using Neuro-Fuzzy Controllers, Amitava Jana

Dissertations

The problem of real time control of a nonlinear dynamic system using intelligent control techniques is considered. The current trend is to incorporate neural networks and fuzzy logic into adaptive control strategies. The focus of this work is to investigate the current neuro-fuzzy approaches from literature and adapt them for a specific application. In order to achieve this objective, an experimental nonlinear dynamic system is considered. The motivation for this comes from the desire to solve practical problems and to create a test-bed which can be used to test various control strategies. The nonlinear dynamic system considered here is an …

Investigation Of Dynamic Friction In Lubricated Surfaces, Hanuman Rachoor

Dissertations

The research reported in this dissertation is concerned with the development of friction models for lubricated contacts. A few analytical models have been developed to investigate the friction under dynamic velocity conditions. In this study, two different tribological situations such as conformal and non-conformal contacts have been chosen. Friction modeling covers boundary, mixed and full fluid film friction regions. A new theory based on the elastic properties of the surface materials, and fluid film properties of the lubricant at the contact has been developed to determine the dynamic friction in boundary, mixed and full hydrodynamic lubrication regions. In the full …