Engineering Commons^™

On The Investigation Of Hot Tearing Behavior Of Continuous Cast Steel, Yanru Lu

Masters Theses

”Hot tearing has long been recognized as a major problem that plagues the development of the continuous casting process and results in low-quality products. Understanding of the mechanisms and the required conditions for the hot tearing formation is important for industries but has not been well-established yet. Thus, this research focuses on the hot tearing issue observed in continuous cast steel, by providing a summary of the current research progress and then introducing a new laboratory method to determine the thermo-mechanical properties relevant to hot tearing of different steel grades under different solidification conditions. In this method, an apparatus was …

Time- And Space-Dependent Uncertainty Analysis And Its Application In Lunar Plasma Environment Modeling, Xinpeng Wei

Doctoral Dissertations

”During an engineering system design, engineers usually encounter uncertainties that ubiquitously exist, such as material properties, dimensions of components, and random loads. Some of these parameters do not change with time or space and hence are time- and space-independent. However, in many engineering applications, the more general time- and space-dependent uncertainty is frequently encountered. Consequently, the system exhibits random time- and space-dependent behaviors, which may result in a higher probability of failure, lower average lifetime, and/or worse robustness. Therefore, it is critical to quantify uncertainty and predict how the system behaves under time- and space- dependent uncertainty. The objective of …

Hydrokinetic Turbine Composite Blades And Sandwich Structures: Damage Evaluation And Numerical Simulation, Mokhtar Fal

Doctoral Dissertations

“Composite materials are gaining interest due to their high strength to weight ratio. This study deals with both experimental and numerical approaches to cover the aspects of the failure of composite materials in hydrokinetic turbine applications. In Part I, the location and magnitude of failure in the horizontal axis water turbine carbon fiber-reinforced polymer (CFRP) composite blades with different laminate stacking sequences were investigated. Two lay-up orientations were adopted for this work ([0⁰]₄ and [0⁰/90⁰]_2s). A finite element analysis model was generated to examine the stresses along the blade. Five angles were introduced to study the effect …

Performance Evaluation Of Alsi10mg Fabricated By A Selective Laser Melting Process, David Michael Murphy

Masters Theses

“Selective laser melting is becoming a widely used additive manufacturing technique that melts metal powder in a layer by layer process in order to build a desired part or geometry. Like many additive processes, selective laser melting allows for fabrication of parts with complex geometries. In order to fabricate a fully dense part there are a number of variables to take into account including: powder characteristics, laser parameters, and environmental parameters. Each of these variables can affect the microstructure and thus the mechanical performance of an additively manufactured part. In this work, the aluminum alloy AlSi10Mg was investigated. AlSi10Mg is …

Modal Analysis As Non-Destructive Testing Technique For Additively Manufactured 304l Stainless Steel Parts, Tristan N. Cullom

Masters Theses

“Non-Destructive Testing (NDT) methods for Additively Manufactured (AM) parts is an ongoing field of research in the additive community due to its ability to determine if a part can be deemed viable for field usage. This study presents modal analysis as a NDT method for AM parts. For production builds that have multiple copies of the same part, a correcting technique can be used such that the frequencies of the parts under test can be reliably compared against each other, which saves both time and money compared to other traditional NDT methods. This study was able to develop a novel …

Influence Of Input Energy On Mechanical Properties Of Laser Powder Bed Fused Aisi 304l Stainless Steel, Tan Pan

Masters Theses

“Powder Bed Fusion process with selective laser melting technique is popularly adopted in additive manufacturing area on account of its layer by layer manufacturing fashion capable of fabricating components with complex internal and external geometries and structures. However, the process-property map is unique and vital for different materials and AM configurations used for fabrication. The process parameter is identified as a significant factor that heavily influences the properties and performances of the printed materials.

Current work aimed to extend the existing knowledge on Laser Powder Bed Fusion fabricated AISI 304L by accessing the influence of varying energy input on the …

Mid-Infrared Chiral Metsurface Coupling With Molecular Vibration, Md Shamim Mahmud

Masters Theses

“The mid-infrared design of chiral metamaterial shows a tremendous absorption capability of infrared rays, and it has the significant application of circular dichroism based device development. Plasmon-phonon coupling is one of the application of metamaterial that provides a new path for tailoring the surface in the nanoscale, which is also applicable in molecules detection. It is possible to change the Plasmon-Phonon coupling strength not only through the chemical change of molecules but also by changing the metamaterial light-matter interaction property. So far, linearly polarized light shows the strong coupling between metamaterial and molecules. However, it is possible to observe strong …

Finite Time Suboptimal Control Design Of Nonlinear Systems With Θ-D Technique And Implementation To Aerospace Applications, Jie Yao

Doctoral Dissertations

“A finite time suboptimal control strategy (named θ - D approximated algorithm) was proposed in this study, which can provide the control engineers with a novel effective and efficient design tool from the finite time optimal perspective. Based on the framework of this proposed method, the original nonlinear dynamics were formulated in pseudo-linear form, and the performance index was denoted by a linear quadratic regulator prototype in this research. After that, the approximated solutions to intractable Hamilton-Jacobi-Bellman (HJB) equation were acquired by putting vanishing perturbation terms into the performance index. By tuning the parameters in perturbation terms, semi-global stability and …

Combustion And Emission Characteristics Of Ic Engines Fueled By Hydrogen And Hydrogen/Diesel Mixtures And Multi-Objective Optimization Of Operating Parameters, Abdulhakim Issa Jabbr

Doctoral Dissertations

“The present study considers combustion of hydrogen in IC engines. In general, the work focuses on simulating the engine performance and emissions at different operation parameters, and using optimization techniques. Task I work deals with the engine performance and emissions of a single cylinder spark-ignition (SI) engine fueled by hydrogen. The engine was simulated at different equivalence ratios, exhaust gas recirculation (EGR) and ignition timing. The results indicate that NOx emissions, engine power, and efficiency are reduced by increasing EGR level, and increased with increasing equivalence ratio and advanced ignition timing. The best operating conditions for hydrogen engines were obtained …

Human Behavior Understanding For Worker-Centered Intelligent Manufacturing, Wenjin Tao

Doctoral Dissertations

“In a worker-centered intelligent manufacturing system, sensing and understanding of the worker’s behavior are the primary tasks, which are essential for automatic performance evaluation & optimization, intelligent training & assistance, and human-robot collaboration. In this study, a worker-centered training & assistant system is proposed for intelligent manufacturing, which is featured with self-awareness and active-guidance. To understand the hand behavior, a method is proposed for complex hand gesture recognition using Convolutional Neural Networks (CNN) with multiview augmentation and inference fusion, from depth images captured by Microsoft Kinect. To sense and understand the worker in a more comprehensive way, a multi-modal approach …

Magnetic Control Of Transport Of Particles And Droplets In Low Reynolds Number Shear Flows, Jie Zhang

Doctoral Dissertations

“Magnetic particles and droplets have been used in a wide range applications including biomedicine, biological analysis and chemical reaction. The manipulation of magnetic microparticles or microdroplets in microscale fluid environments is one of the most critical processes in the systems and platforms based on microfluidic technology. The conventional methods are based on magnetic forces to manipulate magnetic particles or droplets in a viscous fluid.

In contrast to conventional magnetic separation method, several recent experimental and theoretical studies have demonstrated a different way to manipulate magnetic non-spherical particles by using a uniform magnetic field in the microchannel. However, the fundamental mechanism …

Development Of Horizontal Axis Hydrokinetic Turbine Using Experimental And Numerical Approaches, Abdulaziz Abutunis

Doctoral Dissertations

“Hydrokinetic energy conversion systems (HECSs) are emerging as viable solutions for harnessing the kinetic energy in river streams and tidal currents due to their low operating head and flexible mobility. This study is focused on the experimental and numerical aspects of developing an axial HECS for applications with low head ranges and limited operational space. In Part I, blade element momentum (BEM) and neural network (NN) models were developed and coupled to overcome the BEM’s inherent convergence issues which hinder the blade design process. The NNs were also used as a multivariate interpolation tool to estimate the blade hydrodynamic characteristics …

Additive Manufacturing Of Customized Lithium-Ion Batteries: Process Fundamentals And Applications, Xiaowei Yu

Doctoral Dissertations

“In the pasting decades, considerable efforts have been spent in developing the next-generation lithium-ion batteries (LIBs), from advanced active materials to new manufacturing methods. The development of additive manufacturing (AM) has brought new opportunities to LIBs. In this work, two AM methods are introduced for fabricating electrodes of LIBs. The first method is aerosol printing, which is a solvent-based wet additive method. Whereas the second method is a solvent-free, dry printing method. The commonly used materials for current collectors and active materials (including cathodes and anodes) of LIBs are aerosol printed and the electrochemical functionalities of the printed materials are …

In-Situ X-Ray Imaging Of The Selective Laser Melting Process, Meelap M. Coday

Masters Theses

"Fusion-based metal additive manufacturing (AM) has garnered much interest in recent decades. Despite the popularity of fusion-based AM technologies such as selective laser melting (SLM), there are still fundamental questions and uncertainties that need to be addressed. In this work, we focus on the understanding of the undercooling in the SLM process and the uncertainties induced by the laser beam size, power, and scan speed. First, we report the estimation of undercooling in the SLM process from the solidification rate measured by in-situ high-speed synchrotron x-ray imaging, based on the dendrite growth velocity model. The undercooling changes as a function …

Observer-Based Event-Triggered And Set-Theoretic Neuro-Adaptive Controls For Constrained Uncertain Systems, Abdul Ghafoor

Doctoral Dissertations

"In this study, several new observer-based event-triggered and set-theoretic control schemes are presented to advance the state of the art in neuro-adaptive controls. In the first part, six new event-triggered neuro-adaptive control (ETNAC) schemes are presented for uncertain linear systems. These comprehensive designs offer flexibility to choose a design depending upon system performance requirements. Stability proofs for each scheme are presented and their performance is analyzed using benchmark examples. In the second part, the scope of the ETNAC is extended to uncertain nonlinear systems. It is applied to a case of precision formation flight of the microsatellites at the Sun-Earth/Moon …

Trajectory Control Of A Wheeled Robot Using Interaction Forces For Intuitive Overground Human-Robot Interaction, George Leno Holmes Jr.

Doctoral Dissertations

"Effective and intuitive physical human robot interaction (pHRI) requires an understanding of how humans communicate movement intentions with one another. It has been suggested that humans can guide another human by hand through complex tasks using force information only. However, no clear and applicable paradigm has been set forth to understand these relationships. While the human partner can readily understand and adhere to this expectation, it would be difficult for anyone to explain their intuitive motions with strict rules, algorithms, or steps. Uncovering such a procedural framework for the control of robotic systems to execute expected performance simply from force …

Combining Laser Aided Ablation And Polishing To Minimize Surface Roughness Of Additively Manufactured Aluminium Components, Sahil Bipinkumar Patel

Masters Theses

“The surface roughness of additively manufactured parts is much higher than the acceptable range for most applications, thus post-processing is needed to qualify these parts for use. Laser polishing can be used to bring the surface roughness in an admissible range, but if the initial roughness is very high then the energy density for the polishing process needs to be very high to achieve a significant reduction in roughness. This high energy density can produce many process defects. Also, laser polishing alone cannot get rid of high wavelength asperities. Any waviness in the part can be linked with initial waviness …

Characterization And Recyclability Of 304l Stainless Steel Powder For Use In The Selective Laser Melting Process, Austin Taylor Sutton

Doctoral Dissertations

"Powder-bed fusion refers to a subset of additive manufacturing (AM) methods which successively melts and solidifies selected regions within a powder bed on a layer-by-layer basis to construct components directly from computer-aided design files. Laser Powder-Bed Fusion (L-PBF) is a process among the powder-bed fusion techniques that utilizes a laser to consolidate particles into a material with little porosity. During the L-PBF process, the large energy input from the laser causes the production of ejecta in the form of laser spatter and condensate, both of which have the potential to settle in the surrounding powder bed compromising its reusability. In …

A Framework For A Successful Additive Repair System, Todd E. Sparks

Doctoral Dissertations

“The goal of this research is to generate a revolutionary improvement to the usability and usefulness of additive repair technology by integrating a set of tools into a seamless work flow. Insufficient automation in the current repair process is a huge hurdle in achieving cost-effective, reliable repairs. Many opportunities have been missed due to inconsistency, quality issues and lack of robustness and flexibility. The present work addresses deficiencies in preparatory steps such as 2D and 3D geometry processing, parameter estimation, and path planning as well as on-machine execution of the path plan. The bulk of the effort is focused on …

Fabrication And Characterization Of Multifunctional Composites, Aditya R. Thakur

Doctoral Dissertations

“This study details the research to facilitate fabrication and characterization of novel structural composites reinforced with carbon fibers. Across industries, materials with high performance-to-weight ratio are sought after. Using carbon fibers as secondary phases in these proposed composites, specific characteristics can be tailored in these materials to manufacture strong, lightweight, high performance structures. The first part of the research focused on the improvement in the mechanical properties of the composites using carbon fiber reinforcement. As a part of this study, toughened ceramic composites with predictable failure patterns were produced using carbon fiber inclusions. A closed-form analytical model was developed to …