Open Access. Powered by Scholars. Published by Universities.®
- Publication
- Publication Type
Articles 1 - 8 of 8
Full-Text Articles in Engineering
Northrop Grumman Collaboration Project, Nikkia Psomas-Sheridan, Santiago Robles, Ben Elkayam, Benjamin Ulfhake
Northrop Grumman Collaboration Project, Nikkia Psomas-Sheridan, Santiago Robles, Ben Elkayam, Benjamin Ulfhake
Mechanical Engineering
The Northrop Grumman Collaboration Project (NGCP) is a collaborative club project sponsored by Northrop Grumman for the students of Cal Poly San Luis Obispo (CPSLO) and Cal Poly Pomona (CPP) to create a fleet of vehicles to aid in the simulated rescue of stranded hiker. The CPSLO club is responsible for delivering an autonomous flight vehicle that can suppress a fire and retrieve a payload. Mechanical Design Team of the CPSLO team was responsible for the design of the frame, electronics housing, and payload and fire suppression systems.
Northrop Grumman Collaboration Project, Nikkia Rae Psomas-Sheridan, Santiago Robles, Ben Elkayam, Benjamin Ulfhake
Northrop Grumman Collaboration Project, Nikkia Rae Psomas-Sheridan, Santiago Robles, Ben Elkayam, Benjamin Ulfhake
Mechanical Engineering
The Northrop Grumman Collaboration Project (NGCP) is a collaborative club project sponsored by Northrop Grumman for the students of Cal Poly San Luis Obispo (CPSLO) and Cal Poly Pomona (CPP) to create a fleet of vehicles to aid in the simulated rescue of stranded hiker. The CPSLO club is responsible for delivering an autonomous flight vehicle that can suppress a fire and retrieve a payload. Mechanical Design Team of the CPSLO team was responsible for the design of the frame, electronics housing, and payload and fire suppression systems.
Bongoties Tying Machine Design, Zachary Stednitz, Tori Bornino, Jackson Mclaughlin, Shea Charkowsky
Bongoties Tying Machine Design, Zachary Stednitz, Tori Bornino, Jackson Mclaughlin, Shea Charkowsky
Mechanical Engineering
BongoTies are a reusable tool for cable management or general fastening, consisting of a strong rubber band attached to a bamboo pin. BongoTies is a company founded by our sponsor Tim Petros that sells its product on a variety of popular shopping sites, such as Amazon and eBay. Currently, the assembly process is to hand-tie the rubber band to the pin for every BongoTie. This is too slow to keep up with demand, requires a skilled worker with good dexterity, and can cause pain or injury if the rubber band snaps back onto the worker’s fingers. In this senior project …
Blds Pressure Belt, Hailey Earnest, Sean Casteel, Benjamin Bons, Biren Rama
Blds Pressure Belt, Hailey Earnest, Sean Casteel, Benjamin Bons, Biren Rama
Mechanical Engineering
Dr. Westphal has a Boundary Layer Data System (BLDS) that is used to take pressure measurements on the surface of the aircraft. Our team has created a design and manufacturing method for producing the corresponding pressure belt that attaches to Dr. Westphal's system to obtain pressure data.
Design For Additive Manufacturing, Michael Charonnat, Leonardo Franco-Muñoz, Sam Noble, J.P. Purdom
Design For Additive Manufacturing, Michael Charonnat, Leonardo Franco-Muñoz, Sam Noble, J.P. Purdom
Mechanical Engineering
This document outlines the critical design details and timeline for the Design for Additive Manufacturing Senior Project sponsored by Solar Turbines, Inc. The scope of this project encompasses the redesign of two of Solar Turbine’s cast parts for metal additive manufacturing in order to minimize lead time, cost, and weight. With the overall objective of performing in-depth analysis exploring affordability & feasibility, this redesign process will aid Solar Turbines in expanding their knowledge of Design for Additive Manufacturing principles and enable them to further incorporate the use of additive manufacturing into their production processes. The first part that the team …
Improving The Mechanical Performance Of 3d Printed Parts Using Fused Filament Fabrication, Inderpreet Binning
Improving The Mechanical Performance Of 3d Printed Parts Using Fused Filament Fabrication, Inderpreet Binning
Industrial and Manufacturing Engineering
The 3D printing industry has seen rapid growth in the last 10 years and has been called the next industrial revolution. There are several different processes used in 3D printing, but the most popular process is called Fused Filament Fabrication (FFF) or Fused Deposition Modeling (FDM). This is the process where (most commonly) plastic filament enters a nozzle, is heated to a semi-liquid state, and then deposited into a pattern to create a print. One major drawback to this process is that the prints are anisotropic. This means that the strength of the print varies with the orientation that it …
Farmbot, James Cruz, Scott Herrington, Bryan Rodriguez
Farmbot, James Cruz, Scott Herrington, Bryan Rodriguez
Mechanical Engineering
The purpose of this project was to develop the hardware for the current Farmbot to perform its primary functions, and to create a template for a system that would be adaptable for future users and developers. The scope of the project included creating a universal tool mount, a seeding system, and a watering and nutrient mixing system. This project was brought to the students by sponsor Rory Aronson, the creator of Farmbot. The Cal Poly Farmbot team was able to go through an extensive brainstorming and iterative process for each part, where testing was able to be incorporated immediately due …
Selective Laser Sintering; A Design Of Experiments, Philip David Hopkins, Victor Castillo Phd
Selective Laser Sintering; A Design Of Experiments, Philip David Hopkins, Victor Castillo Phd
STAR Program Research Presentations
Additive Manufacturing (AM), also commonly known as 3D Printing or Rapid Prototyping, is a method of manufacturing that provides for the ability to make intricate internal features and easily customizable parts. The concept is to break a Computer Aided Design (CAD) file into a series of thin layers that are sent to the machine and laid down one layer at a time. Just like any other form of processing, material properties can alter by undergoing this process. Manipulating various parameters of the AM process can allow for different properties to be achieved. For this reason, an in depth study will …