Engineering Commons^™

Tribocorrosion And Metal Release From Austenitic Stainless Steels 304 And 201 In Simulated Cassava Food Contact, Robert Addai, Temitope E. Olowoyo, Thalia E. Standish, Jeffrey Daniel Henderson, Ubong Eduok, Yolanda Hedberg

Chemistry Publications

Cassava is the third most significant calorie source in the tropics. Its processing has changed from traditional methods to stainless steel processing machines. This study investigated the influence of cassava on metal release from two common stainless steels, ASTM 304 and 201, with and without friction, and on tribocorrosion (multianalytically) of 304. Cassava was relatively corrosive and hindered repassivation of the surface oxide of stainless steel, but it also acted as a lubricant against mechanical friction. The combined action of friction and cassava caused a significant increase in iron, chromium, nickel, and manganese release from the stainless steels (30–35- fold …

Finite Element Analysis Of Thermal-Mechanical Instabilities In Nonmetallic Friction Composite Material, Joseph-Shaahu Shaahu

Electronic Theses and Dissertations

Thermal-mechanical instability (TMI) has been a research topic of interest as it focuses a lot on transportation systems. Thermal-mechanical instability was first noticed in railway and experimentally studied with a pin-to-pin or pin-to-surface setup of sliding contact. The topic has been extended into brakes and clutches which are two of the most common sliding systems most susceptible to thermal buckling and thermoelastic instability (TEI), where thermal buckling and thermoelastic instability are two sub-categories of thermal-mechanical instability. Thermal-mechanical instability is an ongoing research to better understand the phenomenon and the limits at which such instability occurs. This work delved into the …

Effect Of Electron Irradiation On Mechanical, Tribological And Thermal Properties Of Polytetrafluoroethylene, K. D. Ormanbekov, B. K. Rakhadilov, A. Zh. Zhassulan, N. E. Mukhamedov, A. B. Shynarbek, N. M. Magazov

Eurasian Journal of Physics and Functional Materials

The article presents the study results of the electron irradiation effect on the mechanical, tribological and thermal properties of polytetrafluoroethylene (PTFE). The results allow a better understanding of the processes occurring in the structure of PTFE under irradiation and reveal potential applications of the modified material with improved tribological characteristics, high thermal resistance and mechanical strength. In this work the samples were tested for wear resistance and thermal stability. It was found that the effect of electron irradiation leads to a significant increase in the microhardness of the material by 1.5 times compared to the initial state. However, degradation of …

Securing Pint Glasses On Serving Trays With Magnetic Attachments, Jayden Commendatore

Senior Theses

It is extremely common for servers in the restaurant industry to have pint glasses slip off their serving tray, wasting both time and money for the restaurant. I have designed a sleeve attachment that will clip on to the bottom of a pint glass. The metal sleeve attachment will be attracted to a magnet placed into the serving tray. This increases the normal force of the pint glass, resulting in an increase in the friction force between the tray and sleeve attachment, and helping secure the glass to the tray. In order to optimize the design, the value of the …

Adhesion And Deformation Mechanisms Of Polydopamine And Polytetrafluoroethylene: A Multiscale Computational Study, Matthew Brownell

Graduate Theses and Dissertations

Polydopamine (PDA) has been shown to bond via covalent bonding, van der Waals forces, and hydrogen bonding and is known to adhere strongly to almost any material. The application of PDA between a substrate and a PTFE surface coating has resulted in low friction and a greatly reduced wear rate. Previous research probing the capabilities and limitations of PDA/PTFE films have studied the wear and mechanical properties of the film, but the overall adhesive and deformation mechanisms remain unclear.

In this research, we investigate the tribological properties of PDA and PTFE molecules and composites from the atomic to the microscale …

Manufacturing And Testing The Permanent Magnet Linear Motor, Renjie Kang

Senior Theses

Controlled mechanical motion is vital in many useful applications in technology. Among them, linear motors have advantages over traditional rotating motors. In this work, we built a permanent magnet linear motor to test and measure its energy efficiency. A maximum 29% total energy efficiency, and 67% energy transfer rate, were detected. In addition, a C-shape support structure was added to the moving part in order to increase the moving accuracy. The tests show that, with the support structure, the fluctuation in the vertical direction decreases significantly, but the friction of the system slightly increases.

Hybrid Manufacturing Processes For Fusion Welding And Friction Stir Welding Of Aerospace Grade Aluminum Alloys, Megan Alexandra Gegesky

Masters Theses

"Friction stir welding and processing can provide for joints in aerospace grade aluminum alloys that have preferable material properties as compared to fusion welding techniques. Aerospace grade aluminum alloys such as AA2024-T3 and AA7075-T6 are considered non-weldable by traditional fusion welding techniques. Improved mechanical properties over previously used techniques are usually preferable for aerospace applications. Therefore, by combining traditional fusion welding and friction stir processing techniques, it could be plausible to create more difficult geometries in manufactured parts instead of using traditional techniques. While this combination of fusion welding and friction stir processing is not a new technology, its introduction …

A Comparison Of Nanotribology And Nanoindentation, Steffen Brinckmann, Caroline Fink, Gerhard Dehm

Nanomechanical Testing in Materials Research and Development V

Metal friction and wear is the collective contact and interaction of asperities of micrometer dimension. We use a nanoindenter with tangential force measurement to simulate the behavior in engineering contacts and to fundamentally understand friction and wear.

This presentation investigates the deformation due to a single stroke scratch of a diamond nanoindenter in austenite base. We find that the elastic and plastic equations for static indentation also apply for the dynamic scratching. Additionally, the friction coefficient is found to be normal force dependent and we observe three domains: microstructure dominated friction, plastic plowing dominated wear and wear particle dominated tribology. …

Wear Resistant Polydopamine/Ptfe Nanoparticle Composite Coating For Dry Lubrication Applications, Samuel George Beckford

Graduate Theses and Dissertations

This dissertation presents an investigation into the effect of nanoparticle fillers and a polydopamine adhesive primer on the tribological performance of thin PTFE films. The principal objective of this investigation was to reduce wear in PTFE films, an issue which precludes the use of PTFE films in tribological applications requiring high durability. The friction and wear of the composite films were evaluated using a ball-on-flat configuration in linear reciprocating motion. It was found that the use of a polydopamine adhesive primer reduces the wear of PTFE films more than 600 times. X-ray photoelectron spectroscopy (XPS) results show that a tenacious …

Modeling Of Instabilities And Self-Organization At The Frictional Interface, Vahid Mortazavi

Theses and Dissertations

The field of friction-induced self-organization and its practical importance remains unknown territory to many tribologists. Friction is usually thought of as irreversible dissipation of energy and deterioration; however, under certain conditions, friction can lead to the formation of new structures at the interface, including in-situ tribofilms and various patterns at the interface.

This thesis studies self-organization and instabilities at the frictional interface, including the instability due to the temperature-dependency of the coefficient of friction, the transient process of frictional running-in, frictional Turing systems, the stick-and-slip phenomenon, and, finally, contact angle (CA) hysteresis as an example of solid-liquid friction and dissipation. …

Detailed Finite Element Analysis And Preliminary Study Of The Effects Of Friction And Fastener Pre-Tension On The Mechanical Behavior Of Fastened Built-Up Members, Francisco Javier Bonachera Martin

Open Access Theses

The characterization of fatigue resistance is one of the main concerns in structural engineering, a concern that is particularly important in the evaluation of existing bridge members designed or erected before the development of fatigue design provisions. The ability of a structural member to develop alternate load paths after the failure of a component is known as member-level or internal redundancy. In fastened built-up members, these alternate load paths are affected by the combination of fastener pre-tension and friction between the structural member components in contact. In this study, a finite element methodology to model and analyze riveted and bolted …

Tribological Comparison Of Traditional And Advanced Firearm Coatings, Greg Boban

Master's Theses

The objective of this project is to find which type of coating has the best performance characteristics for finishing firearms. This is accomplished by measuring and comparing several performance characteristics, such as: adhesion, hardness, wear resistance, friction control, and corrosion resistance. Appearance is not a factor since any exterior coating that is flashy can be subdued or camouflaged with special purpose paints, which have proven durable enough for such purposes. Cost will not be a limiting factor for this experiment, but will be discussed in the conclusion as a secondary concern. This data will be used to identify the best …

Wear Analysis Of Cu-Al Coating On Ti-6al-4v Under Fretting, Karl N. Murray

Theses and Dissertations

The effects of changes in the coefficient of friction (CoF) between the contacting surfaces on the fretting wear characteristics of Cu-Al coating on Ti-6Al-4V were investigated. This Cu-Al coating is part of a system that is applied to titanium turbine blades to reduce fretting at the interface. In the application, there is a solid lubricant that is added on top of the coating as an assembly aid and to help reduce the friction while the lubricant remains within the contact. Previous studies have researched the characteristics of the coating without the additional lubricant. In this study, liquid motor oil was …

Friction And Adhesion In Rigid Surface Indentation Of Nitrile Rubber, Stephen Jerrams

Articles

When a rigid body in the form of a plane strain indentor is forced into an elastomer, the asperities on the surface of the indentor are filled by the softer material. As depth of ingress increases, the rubber displaced into the indentor asperities exhibits stick-slip behaviour. The rubber adheres to the rigid body and if the depth of ingress is held at a maximum, the level of adhesion remains constant despite short-term load relaxation occurring in the rubber.

This text describes the influence of a range of factors on indentation forces and adhesion in rigid indentation of hydrogenated nitrile rubbers. …

On Friction And Surface Cracking During Sliding Of Ice On Ice, Maurine Montagnat, Erland M. Schulson

Dartmouth Scholarship

As a complement to earlier measurements on the friction of both granular fresh-water ice and S2 columnar salt-water ice, new experiments were performed on the friction of S2 columnar fresh-water ice sliding against itself at low velocities (5 × 10−7 to 5 × 10−1 m s−1) and at −10°C, using the same double-shear device as was used earlier. The results showed that under a given set of experimental conditions the kinetic coefficient of friction of S2 fresh-water ice compares favorably with that of the other two variants.The experiments also revealed friction-induced surface cracks and recrystallized grains.These deformation features are explained, …

Effect Of Inhibitor On Electrochemical Behavior Of 1cr18 Stainless Steel In Acidic Solution Under Friction, Jinping Xiong

Journal of Electrochemistry

The electrochemical behavior of 1Cr18 stainless steel had been studied using a reciprocating triboelectrochemical equipment under friction in 0.2 mol/L H2SO4 solution with and without addition of thiourea, the frictionized surface of 1Cr18 stainless steel had been examined by the SEM, XPS and IR. The results showed that the loss rate of 1Cr18 stainless steel in the solution could be reduced by addition of thiourea. The adsorption of thiourea on the surface of 1Cr18 stainless steel prohibited the oxidization of Cr3+ to form Cr() and formation of passive film consisting of CrO42- or/and Cr(), and make the passive range to …