Engineering Commons^™

Silver Centers Induced In Borate Glasses: Esr And Optical Studies, Hadia El Zayyat

Archived Theses and Dissertations

No abstract provided.

Inhibitors And Retarders For The Free Radical Polymerization Of Alpha-Methylstyrene, Alexander Accetta

Masters Theses

No abstract provided.

Some Structural Aspects Of Ni2+ In Potassium Haloborate Glasses, Samia Sidhom

Archived Theses and Dissertations

No abstract provided.

Subsolidus Equilibria And Metastable Phase Development In The System Zro₂-Al₂O₃-Sio₂, Charles Christopher Sorrell

Bachelors Theses

"Subsolidus equilibria in the low silica portion of the system ZrO₂-Al₂O₃-SiO₂ were studied by X-ray diffraction of quenched samples fired at 1300°, 1400°, and 1480°C. Samples prepared as powders from combinations of a-Al₂O₃, Al(OH)₃, silicic acid, ZrO₂, and kaolinite reacted very slowly at 1300° and 1400°C and the trends toward equilibria are not apparent. A mixture of zircon and Al(OH)₃ reacted slowly at 1480°C to form mullite and ZrO₂, indicating that the latter phases are the stable assemblage rather than zircon and alumina. A gel prepared from aluminum nitrate, zirconyl nitrate, and colloidal silica reacted at 1480°C to form alumina, …

Computation Of Potential And Potential Gradient Around Bundled Conductors, Mamdouh Hossny Ibrahim

Archived Theses and Dissertations

No abstract provided.

Characterization Of Two Mexican Raw Dolomites For Refractory Brick Production, Rodolfo Trevino Cantu

Masters Theses

"Two Mexican dolomites were characterized in order to discover their suitability for production of refractory brick.

The results were compared with other dolomites from American Companies. Some samples were burned in a gas fired Laboratory Furnace and others were obtained in the burned state after processing in Industrial Rotary Kilns.

The characterization procedures included X-Ray Diffraction, Scanning Auger Microprobe, DTA and TGA techniques, Chemical Analysis and Bulk Density measurements.

The procedure to control the quality of the dead-burned dolomite at the industrial level was established taking as the main criteria, bulk density, hydration susceptibility, and impurity levels"--Abstract, page ii.

Application Of Voltammetry To Copper Electrodeposition, Louis Francis Toth Jr.

Doctoral Dissertations

"A study was undertaken to determine the feasibility of using voltammetry and scanning electron microscopy techniques to characterize copper deposition from an acid-sulfate electrolyte. The main process variables investigated were temperature and addition agents (chloride ion, glue, separan or thiourea) at different concentrations, over a range of current densities. Cathodes employed were either polycrystalline titanium or copper. Some long-time copper deposits were also made using Ti cathodes and the orientations of these deposits were determined by x-ray diffraction.

Observations of copper crystals produced during voltammetry scans, on a Ti cathode, indicated that a characteristic morphology was associated with each type …

Variables Affecting The Rate Of Solution Of Mold Inoculants In Cast Iron, Jose Osorno Fonnegra

Masters Theses

"The purpose of this investigation was to measure the effectiveness of an inoculant alloy reacting with molten cast iron in a reaction chamber properly located in the gating system.

The chemical composition of the gray iron was held constant while several metallurgical factors were varied to produce test samples with different cementite thicknesses. These chill depths were measured as an indication of the inoculation effectiveness.

Appreciable differences in chilling tendency were observed within the different variables studied. The results indicate that pouring temperature, as well as the other variables studied, are of considerable importance when dealing with inoculation of gray …

Corrosion And Electrochemical Behavior Of Indium And Indium-Bismuth Alloys In Hydrochloric Acid, Yar Ming Wang

Doctoral Dissertations

"The corrosion of In-Bi alloys was studied using X-ray, scanning electron microscopy, atomic absorption spectroscopy, and cyclic voltammetry techniques.

Calculated activation energy values indicated that the corrosion of In-Bi alloys was activation controlled. The effect of amine mixtures on the corrosion of In and In₂Bi (ß₁ phase) was studied. Morphological studies revealed that the porosity of the resulting physical surface structure was influential in determining the corrosion rate. In deaerated 3N HCl solutions, the selective dissolution of indium was the predominant mechanism in the corrosion of In-Bi alloys. The corrosion was always accompanied by a phase change …