Engineering Commons^™

The Recovery Of Copper In Sulphide Ores By Roasting, Leaching, And Electrolysis, Jack S. Greenough

Bachelors Theses and Reports, 1928 - 1970

Sulphide ores of copper are insoluble in dilute sulphuric acid leaching solutions, but a very high extraction can be obtained if the copper ore is in the oxidized condition. The problem is to convert the sulphide into the oxide form. This can be done by giving the sulphide ore an oxidizing-sulphatizing roast. Copper sulphate is soluble in water, so acid will be saved in the leaching process if copper sulphate is present. The iron in the copper sulphide ores is present as pyrite, or in combinations as bornite, or chalcopyrite.

The Effect Of The Fe2: Fe3 Ratio Upon The Current Efficiency In The Electrolysis Of A Copper Sulfate Solution Containing Iron Sulfate, Roy Macfarland

Bachelors Theses and Reports, 1928 - 1970

In the treatment of copper ores by hydro-electro-metallurgical methods, not only is copper deposited, but other metals are also dissolved. In practice it has been found* that iron, under certain conditions, causes the copper to deposit on the cathode as a nonadherent precipitate and also that the iron in solution causes a great decrease in current efficiency, es­pecially when the electrolysis is conducted by operating with a higher current density at the cathode than at the anode.

The present investigation deals with the effects of the two valences of iron on the current efficiency and endeavors to determine whether or …

Some Notes On The Composition Of "Copper Pitch", Richard R. Matthew

Bachelors Theses and Reports, 1928 - 1970

A supply of so-called "copper pitch" ore was received by the Montana Bureau of Mines and Geology in response to a request by them from a resident of Kalispell, who had previously sent a specimen to the Bureau for a mineralogical analysis.

Since this material was little known and had apparently received but little study under a reflec­ting microscope, it was thought that such a study might throw some light on the mineralogical and chemical composition of the material.

The Aplitic Body Bordering Roosevelt Drive South Of Butte, Montana, Edward B. Trueworthy Jr.

Bachelors Theses and Reports, 1928 - 1970

The area studied consists of a large body of aplite situated 12 miles south of Butte. It extends eastward almost to the Butte-Pipestone road, southward to Lime Kiln Hill and westward a distance of 3000 feet.

The petrographic work was supplemented by a map of the area. Special attention was given to those frequent "Limonite Specks" found in the aplite.

The Rate Of Precipitation Of Copper Aluminide In The Silver Rich Silver-Copper-Aluminum Alloys, Thomas Finley Mcbride

Bachelors Theses and Reports, 1928 - 1970

In order to determine the best annealing temperature at which to age-harden the alloys, hardness tests on speci­men annealed for different lengths of time at different temperatures were made.

The Effect Of Hydrogen Overvoltage On The Electrolytic Deposition Of Zinc, John M. Munzenrider, Kenneth O. Sweeney

Bachelors Theses and Reports, 1928 - 1970

In the deposition of metallic zinc by electro­lysis from neutral or acid solution, little difficulty is experienced provided certain impurities are absent from the electrolyte. The use of the process has long been considered as a potential source, patents on the process having been issued as early as 1880. However, the early experimenters failed to realize the importance of impurities in the electrolyte, and for this reason, the process suffered several severe setbacks when commercial plants were built.

The Electrolytic Deposition Of Chromium Upon Aluminum, E. Fults, L. D. Voerge

Bachelors Theses and Reports, 1928 - 1970

The purpose or this investigation is primarily to determine the best conditions for plating chromium on aluminum. The work was carried out with the hope of obtaining coherent deposits, and of determin­ing the conditions under which such deposits may be duplicated.

Pressure Transmission And Green Strength Of Clays As Affected By Time Of Ageing, William Thomas Kay

Bachelors Theses

"Perfect dry pressing could only be attained if the mix possessed the properties of water in so far as pressure transmission is concerned. There are many factors, however, which tend to interfere with the transmixxion sic of pressure in the clay block, such as, - Differences in grain size, friction between the grains, entrapped air, dragging of the clay on the sides of the mould box and many other minor causes. In an effort to solve some the problems that are of vital interest to the Dry Press industry, the Committee on Dry Press Process of the National Brick Manufacturers …

The Purification Of Missouri Fire Clays, James Joseph Offutt

Bachelors Theses

"At the present time there appears to be an unlimited supply of high grade fire clay available for most any purpose. But some time in the future there will rise the problem of purifying the low grade clay to such an extent that it will be used in high grade fire clay products. Whatever purification method may be employed it must be applicable on a commercial scale and the cost of purification must be very low. Until the present time little if any work along this line has been reported. Apparently no one has ever attempted any serious efforts to …

Development Of An Artificial Substitute For Firestone, Joseph Edwin Stevens

Bachelors Theses

"Firestone is a natural occurring silica rock which is cut up into brick and shapes and used for lining cupolas. This rock is found in the east, mostly in Pennsylvania. It is dense, having a porosity of 5.6% raw and 16% after firing to cone 18. Its volume expansion upon firing was calculated to be 19.2%. Its appearance shows that it is evidently fine grained silica bonded with a small amount of clay and siliceous cement. This rock has such desirable characteristics for use in cupola linings that it would be of great importance to duplicate this rock synthetically in …

The Effect Of Different Rates Of Ram Movement On The Transmission Of Pressure In Dry Pressed Bodies, Frank Joseph Zvanut

Bachelors Theses

"The object of this investigation was to study the relationship between the rate of ram movement during the initial application of pressure and the transmission of pressure in the dry press process; to study the effect of various rates of ram movement; and, as far as possible, to determine the critical rate for uniform pressure distribution within the body"--Purpose of Investigation, page 4.

The Effect Of Grain Sizing On The Strength And Porosity Of Refractory Grog Bodies, Robert Stafford Green

Bachelors Theses

"The object of this work was to determine the effect of grain sizing on the strength and porosity of grog bodies. The investigation was carried out by the general method of making up bars of varying grain composition and testing them for strength and porosity"--page 1.

Die Steels And The Heat-Treatment Of Dies For Use In Die Casting Aluminum Base Alloys, Elmer Gammeter

Professional Degree Theses

"Although the casting of metals is an ancient art, it was not until recent years that metals were cast in large quantities in metallic molds. The increasing demands on the industry for greater production brought about this change which essentially involves the introduction of molds capable of producing numerous castings in preference to the use of non-metallic molds which were destroyed in making the casting"--General Consideration of the Die Casting Process, page 1.

Concentration Of An Oxidized Lead Ore From Southeast Missouri, Robert Edward Evans

Masters Theses

"In the main ore bodies of the Southeast Missouri Lead Belt the lead occurs as galena disseminated in dolomite. The concentration in the mills is by tabling and flotation. The grade of the concentrates and the recovery of the galena are excellent. However, in certain areas of some of the mines ore has been developed that does not concentrate so readily. Because of its reddish brown color this ore is known locally as "red ore", and the presence of oxidized lead has been suspected. The purpose of this investigation was to determine the extent to which oxidized lead minerals were …

The Control Of Anode Corrosion, Edward Arthur Godat

Masters Theses

"This particular study of the control of anode corrosion in connection with the production of zinc by electrolytic deposition from commercial solutions is a continuation of work started at the Missouri School of Mines and Metallurgy in 1929. It is not a new problem or even a new phase of the problem, but rather an attempt to confirm some of the ideas brought out in previous work and to perhaps more definitely establish some of the conclusions drawn from insufficient data, by more extensive tests and by attacking the problem from a slightly different angle"--Introduction, page 1.