Engineering Commons^™

A Study Of The Diffusion Characteristics Of Tungsten Bar Stock And Tungsten Produced Via Direct Metal Laser Sintering (Dmls), Jonathan Robert Bruss

Master's Theses (2009 -)

Using a vacuum hot extraction method diffusivity and concentration of hydrogen were measured in samples of tungsten bar stock and direct metal laser sintered (DMLS) tungsten. It was found that the tungsten bar stock closely adhered to the model established by Frauenfelder. The DMLS samples approximately follow a downward sloping trend over the 500K-1200K temperature range. The trend is opposite of what is expected suggesting processing has a major effect on diffusion behavior. A CFD model was created using ANSYS Fluent to simulate the diffusion behavior. The model functions by separating out diffusion mechanisms and solving Fick’s law with each …

Plasticized Polymer Coatings For Sh-Saw Sensors For High Sensitivity And Long-Term Monitoring Of Btex Analytes In Liquid Phase, Pintu Adhikari

Master's Theses (2009 -)

BTEX compounds (benzene, toluene, ethylbenzene, and xylene) are constituents of crude oil and hazardous to human health. Among them, benzene has the lowest maximum contaminant level for drinking water because of its carcinogenicity. Spills or leakage from underground storage tanks or hazardous waste sites can contaminate nearby groundwater with these volatile organic compounds. Therefore, it is very important to detect the presence of BTEX contamination as early as possible in order to start the remediation process and maintain a healthy environment. To develop an in-situ continuous monitoring sensor system, shear horizontal surface acoustic wave (SH-SAW) sensor devices are being investigated …

Analysis Of Fatigue Crack Propagation In Welded Steels, Roberto Angelo Demarte

Master's Theses (2009 -)

This thesis presents the study of fatigue crack propagation in a low carbon steel (ASTM A36) and two different weld metals (AWS A5.18 and AWS A5.28). Fatigue crack propagation data for each weld wire is of interest because of its use for predicting and analyzing service failures. Fatigue crack growth test specimens were developed and fabricated for the low carbon steel base metal and for each weld wire. Weld specimens were stress relieved prior to fatigue testing. Specimens were tested on a closed-loop servo hydraulic test machine at two different load ratios. Fatigue test data was collected to characterize both …

Cyclic Behavior Of A Hybrid Light Gauge And Hss Mezzanine Structural System, Michael John Kren

Master's Theses (2009 -)

Cold-formed steel is emerging as an alternative material in the building industry to hot-rolled steel for smaller buildings and indoor structures also called mezzanines. Cyclic testing of a full-scale mezzanine structures composed of cold-formed structural channel beams connected to hollow structural steel (HSS) columns cap plates using wedge expansion anchors at the base plate to generate rotation restraint, is performed in this research. The characteristics of the structure will be explained by displaying full experimental results of structural testing. Unfortunately, limited experimental data outlining the behavior of these structures is available and design criteria is very limited. Thus, there is …

A Multi-Scale Approach To A Greater Understanding Of The Behavior Of Heterogeneous Materials Under Dynamic Loading, Andrew J. Van Vooren

Master's Theses (2009 -)

The penetration of granular materials is of interest to a variety of different fields, and is an active area of research. The objective of this project is to gain understanding of the dynamics of a projectile penetrating into a granular material. To do this, experiments were run and a numerical model was created.

A dart gun was used to accelerate an aluminum dart to velocities around 100 m/s, which then impacted a target tank filled with Ottawa sand. The dart flew along a view window, which allowed for a recording of the penetration event using a high speed camera. Pressure …

Light-Activation Influence On The Thermal Analysis Of A Resin-Modified Glass-Ionomer, Raksha Srinivas

Master's Theses (2009 -)

The acid-base and light polymerization reactions in resin modified glass ionomers (RMGI) have been shown to compete and possibly inhibit one another during early RMGI development. Earlier beginning times of light polymerization initiation may limit the acid-base reaction and if time allowed for the acid-base components to react is increased, the extent of light cure reaction may be lesser. The thermal behavior of a commercially available RMGI was investigated in relation to a light initiation regimen using a differential scanning calorimeter (DSC). The relationship between delay in light initiation or no light initiation and the resultant set matrix of the …