Engineering Commons^™

On The Investigation Of Hot Tearing Behavior Of Continuous Cast Steel, Yanru Lu

Masters Theses

”Hot tearing has long been recognized as a major problem that plagues the development of the continuous casting process and results in low-quality products. Understanding of the mechanisms and the required conditions for the hot tearing formation is important for industries but has not been well-established yet. Thus, this research focuses on the hot tearing issue observed in continuous cast steel, by providing a summary of the current research progress and then introducing a new laboratory method to determine the thermo-mechanical properties relevant to hot tearing of different steel grades under different solidification conditions. In this method, an apparatus was …

Performance Evaluation Of Alsi10mg Fabricated By A Selective Laser Melting Process, David Michael Murphy

Masters Theses

“Selective laser melting is becoming a widely used additive manufacturing technique that melts metal powder in a layer by layer process in order to build a desired part or geometry. Like many additive processes, selective laser melting allows for fabrication of parts with complex geometries. In order to fabricate a fully dense part there are a number of variables to take into account including: powder characteristics, laser parameters, and environmental parameters. Each of these variables can affect the microstructure and thus the mechanical performance of an additively manufactured part. In this work, the aluminum alloy AlSi10Mg was investigated. AlSi10Mg is …

Enhanced Electrochemical Performance Of Li-Ion Battery Cathodes By Atomic Layer Deposition, Yan Gao

Doctoral Dissertations

”Li-ion battery now plays an irreplaceable role in supplying green and convenient energy. In this work, atomic layer deposition (ALD) was used to modify Li-ion battery cathode particles for performance enhancement.

An ultrathin and conductive CeO₂ ALD film was deposited on Li-rich layered cathode particles, of which the specific capacity and cyclic stability were significantly improved. On the same cathode particles, FeO_x ALD and post-annealing resulted in a stable and conductive surface spinel phase to improve the performance.

Synergetic TiN coating and Ti doping were performed on a LiFePO₄ (LFP) cathode and extended its cycle life. The …

Inclusion Control In Steel Castings, Koushik Karthikeyan Balasubramanian

Masters Theses

“Non-metallic inclusions are mainly comprised of oxides, sulfides, and nitrides, and are formed in liquid steel during the melting and refining process, as a result of reoxidation, worn-out refractories, or entrained slag. The notch toughness of high strength steels is particularly susceptible to the type, number, size, and distribution of non-metallic inclusions. High manganese and aluminum austenitic steels, or Fe-Mn-Al steels, have gained much interest in the military and automotive sector because of their excellent combinations of high strength and toughness. However, these steels are subject to both oxide bifilms and aluminum nitride, AlN, inclusions which form during melting and …

Studying The Effects Of Various Process Parameters On Early Age Hydration Of Single- And Multi-Phase Cementitious Systems, Rachel Cook

Doctoral Dissertations

”The hydration of multi-phase ordinary Portland cement (OPC) and its pure phase derivatives, such as tricalcium silicate (C₃S) and belite (ß-C₂S), are studied in the context varying process parameters -- for instance, variable water content, water activity, superplasticizer structure and dose, and mineral additive type and particle size. These parameters are studied by means of physical experiments and numerical/computational techniques, such as: thermodynamic estimations; numerical kinetic-based modelling; and artificial intelligence techniques like machine learning (ML) models. In the past decade, numerical kinetic modeling has greatly improved in terms of fitting experimental, isothermal calorimetry to kinetic-based modelling …

Thermodynamic Investigations Of Pure And Blended Cement Mixtures, Jonathan Lapeyre

Doctoral Dissertations

” This research is made up of several studies. The first study focused on understanding the reaction kinetics of Ca₃SiO₅ and metakaolin (MK) mixtures compared to Ca₃SiO₅ and silica fume (SF) mixtures. It was shown that MK was a more effective additive than SF at small replacement levels (i.e. ≥ 10% by mass) while higher replacement levels of MK became a detriment due to excess (Al(OH)₄¯) ions preventing the nucleation and growth of C-S-H. In a follow-up study where the MK particle size distribution (PSD) was modified, similar effects were observed but …

Prediction Of Crack Propagation In Zrb₂-Carbon Based Composites Using The Extended Finite Element Method, Leiren Danielle Jarvis

Masters Theses

“The ultra-high temperature ceramic, zirconium diboride (ZrB₂) has long been researched for applications in extreme environments. Its high strength (> 400 MPa) and thermal conductivity (> 100 W/m•K) make it a candidate for use in hypersonic fight, but a low fracture toughness (< 3 MPa•m^1/2) limits this use. In order to increase the fracture toughness without compromising the strength and thermal conductivity, experimental research has focused on the viability of engineered architectures using multiple materials to create a macrostructure. These architectures allow for the increase of fracture toughness thru crack deflection in the material.

Two architectures in particular, …

In-Situ X-Ray Imaging Of The Selective Laser Melting Process, Meelap M. Coday

Masters Theses

"Fusion-based metal additive manufacturing (AM) has garnered much interest in recent decades. Despite the popularity of fusion-based AM technologies such as selective laser melting (SLM), there are still fundamental questions and uncertainties that need to be addressed. In this work, we focus on the understanding of the undercooling in the SLM process and the uncertainties induced by the laser beam size, power, and scan speed. First, we report the estimation of undercooling in the SLM process from the solidification rate measured by in-situ high-speed synchrotron x-ray imaging, based on the dendrite growth velocity model. The undercooling changes as a function …

Intrinsic Mechanical Properties Of Zirconium Carbide Ceramics, Nicole Mary Korklan

Masters Theses

“This research focuses on the processing and mechanical properties of zirconium carbide ceramics (ZrC_x). The first goal of this project was to densify near stoichiometric (i.e., x as close to 1 as possible) and nominally phase pure ZrC_x. The maximum stoichiometry achieved for the ZrC_x (C/Zr ratio of 0.92) was measured using gas fusion analysis. Hot pressing was used to obtain dense ZrC_x. Archimedes was used to determine the relative density of hot pressed ZrC_x at > 95%. Scanning electron microscopy (SEM) was used to determine the overall microstructure of the hot pressed …

Understanding The Deformation Mechanisms In Ni-Based Superalloys With Using Crystal Plasticity Finite Element Method, Tianju Chen

Doctoral Dissertations

“Ni-based superalloy is considered as a good candidate due to its excellent resistance to elevated temperature deformation for long term period application. Understanding the deformation and failure mechanisms of Ni-Based superalloys is very helpful for providing design guidelines for processing Ni-based superalloys. Experimental characterization indicates that the deformation mechanisms of Ni based superalloy is strongly microstructure dependent. Besides, damage transform from the void nucleation to the macro cracks by voids growth leading to the failure of the Ni-based superalloys are also showing strong microstructure sensitivity. Therefore, this work focuses on the prediction and comprehension of the deformation and void growth …

Removal Of Non-Metallic Inclusions From Molten Steel By Ceramic Foam Filtration, Soumava Chakraborty

Doctoral Dissertations

”Ceramic filters are routinely used in steel foundries to remove non-metallic inclusions from steel melt. Removal efficiency for both solid and liquid inclusions by magnesia-stabilized zirconia foam filters (10ppi) were evaluated and distribution of the captured inclusions through the filter thickness was also investigated. A mold design was developed using a commercial computational fluid dynamics software package to produce two castings that fill simultaneously, one with a filter and the other without a filter, from a single ladle pour, while also matching the fill rates and avoid turbulence and reoxidation during pouring. An industrial-scale experiment was also performed to investigate …

Development Of Lightweight Materials By Meso- And Microstructure Control, Myranda Shea Spratt

Doctoral Dissertations

”In this work, two lightweight structures – lattice structures and metal matrix syntactic foams (MMSF) – were studied. Honeycomb lattices were manufactured by powder bed selective laser melting (SLM) from 304L stainless steel. The wall thicknesses of these structures ranged from 0.2 to 0.5 mm. Surface roughness was the primary cause of dimensional mismatch between the expected and as-built structures with an average wall thickness increase of 0.12 mm. The strength of the honeycombs increased with increasing wall thickness. A feature of the SLM microstructure, the melt pool boundary, was also studied as a part of this work. 3D models …

Transition Metal Chalcogenide Hybrid Systems As Catalysts For Energy Conversion And Biosensing, Siddesh Umapathi

Doctoral Dissertations

"Generation of hydrogen and oxygen through catalyst-aided water splitting which has immense applications in metal air batteries, PEM fuel cells and solar to fuel energy production, has been one of the critical topics in recent times. The state of art oxygen evolution reaction (OER), oxygen reduction reaction (ORR), hydrogen evolution reaction (HER) catalysts are mostly comprised of precious metals. The current challenge lies in replacing these precious metal-based catalysts with non-precious earth-abundant materials without compromising catalytic efficiency.

This research explores mixed metal selenides containing Fe-Ni, Fe-Co and RhSe which were hydrothermally synthesized and/or electrodeposited and tested for OER and ORR …