Engineering Commons^™

The Feasibility Of High Strength Stainless Steel In Prestressing Applications For Pile Design, Cara Morton

USF Tampa Graduate Theses and Dissertations

Approximately 50% of the Nation’s infrastructure was built over 40 years ago for a 50 year service life according to the National Association of Corrosion Engineers [72]. To mitigate the cost of major repair or replacement at 50 years, AASHTO now requires all new bridge construction to have a 100 year service life. One of the main challenges in achieving this goal is avoiding corrosion, especially in warm, saltwater environments like those found in the Southeastern United States. Elements that cross the waterline (piles) are a weak link the infrastructure. Good quality concrete easily maintains a service life of 75+ …

The Effect Of Processing Conditions On The Energetic Diagram Of Cdte Thin Films Studied By Photoluminescence, Shamara P. Collins

USF Tampa Graduate Theses and Dissertations

The photovoltaic properties of CdTe-based thin films depend on recombination levels formed in the CdTe layer and at the heterojunction. The localized states are resultant of structural defects (metal sublattice, chalcogen sublattice, interstitial), controlled doping, deposition process, and/or post-deposition annealing. The photoluminescence study of CdTe thin films, from both the bulk and heterojunction, can reveal radiative states due to different defects or impurities. Identification of defects allows for potential explanation of their roles and influence on solar cell performance. A thorough understanding of the material properties responsible for solar cell performance is critical in further advancing the efficiency of devices. …

Computational Discovery Of Energetic Polynitrogen Compounds At High Pressure, Brad A. Steele

USF Tampa Graduate Theses and Dissertations

High-nitrogen-content energetic compounds containing multiple N-N bonds are an attractive alternative towards developing new generation of environmentally friendly, and more powerful energetic materials. High-N content translates into much higher heat of formation resulting in much larger energy output, detonation pressure and velocity upon conversion to large amounts of non-toxic, strongly bonded N2 gas. This thesis describes recent advances in the computational discovery of group-I alkali and hydrogen polynitrogen materials at high pressures using powerful first-principles evolutionary crystal structure prediction methods. This is highlighted by the discovery of a new family of materials that consist of long-sought after all-nitrogen N􀀀 5 …

In Situ Extrinsic Doping Of Cdte Thin Films For Photovoltaic Applications, Imran Suhrid Khan

USF Tampa Graduate Theses and Dissertations

The Cadmium Telluride thin film solar cell is one of the leading photovoltaic technologies. Efficiency improvements in the past decade made it a very attractive and practical source of renewable energy. Considering the theoretical limit, there is still room for improvement, especially the cell’s open circuit voltage (VOC). To improve VOC, the p-type carrier concentration and minority carrier lifetime of the CdTe absorber needs to be improved. Both these parameters are directly related to the point defect distribution of the semiconductor, which is a function of deposition stoichiometry, dopant incorporation and post-deposition treatments.

CdTe films were deposited by the Elemental …

Direct Print Additive Manufacturing Of Optical Fiber Interconnects, Roger B. Tipton

USF Tampa Graduate Theses and Dissertations

High performance communications, sensing and computing systems are growing exponentially as modern life continues to rely more and more on technology. One of the factors that are currently limiting computing and transmission speeds are copper wire interconnects between devices. Optical fiber interconnects would greatly increase the speed of today’s electronic devices. In this study it has been demonstrated that by using a new Direct Print Additive Manufacturing (DPAM) process of Fused Deposition Modeling (FDM) of plastic and micro-dispensing of pastes and inks, we can 3D print single and multi-mode optical fibers in a controlled manner such that compact, 3-dimensional optical …

Non-Precious Metal Catalysts For Oxygen Reduction Reaction In Alkaline Solutions, Zhewen Yin

USF Tampa Graduate Theses and Dissertations

Mesoporous WO3 powders were prepared via sol-gel processing synthesis using nonionic surfactant Pluronic (P-123) as the template. The influences of heating temperature on the pore structure and properties of WO3 powders were investigated. Three kinds of modifications were compared and evaluated after finding out the best heating condition. Different amount of lanthanum was doped into mesoporous WO3 to improve its Oxygen Reduction Reaction (ORR) activity. Several factors contributing to the increase of catalytic performance were discussed. Vulcan carbon powder was also used as a support to increase the catalysts’ electrical conductivity as well as dispersity. The component, microstructure and specific …

Supported Perovskite-Type Oxides: Establishing A Foundation For Co2 Conversion Through Reverse Water-Gas Shift Chemical Looping, Bryan J. Hare

USF Tampa Graduate Theses and Dissertations

Perovskite-type oxides show irrefutable potential for feasible thermochemical solar-driven CO₂ conversion. These materials exhibit the exact characteristics required by the low temperature reverse water-gas shift chemical looping process. These properties include structural endurance and high oxygen redox capacity, which results in the formation of numerous oxygen vacancies, or active sites for CO₂ conversion. A major drawback is the decrease in oxygen self-diffusion with increasing perovskite particle size. In this study, the La_0.75Sr_0.25FeO₃ (LSF) perovskite oxide was combined with various supports including popular redox materials CeO₂ and ZrO₂ along with more abundant …