Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- Additive Manufacturing (2)
- AF9628 Steel (1)
- Aerospace Industry (1)
- Ceramic Matrix Composites (1)
- Composite Materials (1)
-
- Composite materials (1)
- Compressor Blades (1)
- Crack Propagation (1)
- Creep Tests (1)
- Explosives--Measurement (1)
- Failure Mode and Effect Analysis (1)
- Fatigue Cracking (1)
- Hall effect--measurement (1)
- Heat Treatment (1)
- High temperature (1)
- Intermetallic compunds (1)
- Jet Engines (1)
- Laser Powder Bed Fusion (LPBF) (1)
- Materials Processing (1)
- Metals (1)
- Microstructure (1)
- Modulus of Elasticity (1)
- Notch Sensitivity (1)
- Photoluminescence--Measurement (1)
- Physical Properties (1)
- Platinum alloys (1)
- Radiation--Measurement (1)
- Selective Laser Melting (1)
- Semiconductors--Electrical properties (1)
- Tantalum (1)
Articles 1 - 7 of 7
Full-Text Articles in Engineering
Creep Of Nextel 720/Alumina Ceramic Matrix Composite With Diamond-Drilled Effusion Holes At 1200°C In Air And In Steam, Megan L. Harkins
Creep Of Nextel 720/Alumina Ceramic Matrix Composite With Diamond-Drilled Effusion Holes At 1200°C In Air And In Steam, Megan L. Harkins
Theses and Dissertations
A recent study evaluated tensile stress-strain and tensile creep behavior of an oxide-oxide composite (Nextel™720/alumina) with laser-drilled effusion holes at 1200°C. It was determined that the presence of laser-drilled holes degraded the mechanical properties and performance of the CMC as a result of damage caused to the composite microstructure by the laser drilling process. Based on these results, the present effort sought to assess the effects of diamond-drilled holes on the mechanical behavior of this CMC. Tensile properties of the N720/A composite at 1200°C in laboratory air were unaffected by the presence of an array of 17 diamond-drilled effusion holes. …
Fracture Toughness And Fatigue Crack Growth Rate Characterization Of Inconel 718 Formed By Laser Powder Bed Fusion, Charles C. Hohnbaum
Fracture Toughness And Fatigue Crack Growth Rate Characterization Of Inconel 718 Formed By Laser Powder Bed Fusion, Charles C. Hohnbaum
Theses and Dissertations
Continuing improvement in the field of AM of metals provides the opportunity for direct fabrication of aerospace parts. AM was once used in large part for rapid prototyping but improvements in technology and increases in the knowledge base of AM materials has provided the opportunity for manufacture of AM parts for operational use. The ability to create low numbers of unique parts without having to invest in expensive tooling provides great economic incentive to utilize this technique. IN718 is the most common high temperature alloy used in the aerospace industry and lends itself readily to formation by LPBF. The superior …
Process Parameter Development Of Additively Manufactured Af9628 Weapons Steel, Erin M. Hager
Process Parameter Development Of Additively Manufactured Af9628 Weapons Steel, Erin M. Hager
Theses and Dissertations
The manufacture of components in Additive Manufacturing processes is limited by the range of materials available. Qualification of materials for Additive Manufacturing is time intensive, and is often specific to a single type of machine. In this study, an approach to selecting power, speed, and hatch spacing values for a newly powderized material, AF9628 weapons steel, is described that results in highly dense (>99.9%) parts on an MLab 200R Cusing. Initial power and speed values used in a weld track study were selected based on a survey of parameters used on similar materials, with a focus on the energy …
Advanced Radiometry For High Discrimination Explosive Fireball Discrimination, Steven E. Slagle
Advanced Radiometry For High Discrimination Explosive Fireball Discrimination, Steven E. Slagle
Theses and Dissertations
The high explosive fireball phenomenological model for the mid wave infrared spectrum, developed by AFIT, performs classification from spectral signatures was modified to use radiometric intensities. Five bands were sequentially fit to derive the five physical fit parameters describing the fireball's temperature, size, soot absorption coefficient within 16% and emissions from the H2O and CO2 concentrations within 333% of the spectral model. This was improved by changing the model's band sizes, center, and fitting methods where all five fit parameters were matched to within 17% of spectral model. This demonstrated that a combination of radiometric intensities could …
Investigation Of Electrical And Optical Properties Of Bulk Iii-V Ternary Semiconductors, Travis C. Gomez
Investigation Of Electrical And Optical Properties Of Bulk Iii-V Ternary Semiconductors, Travis C. Gomez
Theses and Dissertations
Bulk grown III-V ternary semiconductors of In0.08Ga0.92Sb and In0.15Ga0.85As were investigated through Hall-effect and photoluminescence measurements to determine carrier concentration, mobility, sheet resistivity, and luminescence spectrum. In the past, epitaxial layers of ternary compounds have been grown on binary compound substrates, and thus very limited lattice matched ternary alloys were available. Recently, bulk grown ternary substrates have been developed, and it has presented a renewed interest in using these substrates to grow high quality ternary compounds for use in many next generation optoelectronic devices. The results of photoluminescence (PL) study for the …
Nondestructive Evaluation Of Aircraft Composites Using Terahertz Time Domain Spectroscopy, Christopher D. Stoik
Nondestructive Evaluation Of Aircraft Composites Using Terahertz Time Domain Spectroscopy, Christopher D. Stoik
Theses and Dissertations
Terahertz (THz) time domain spectroscopy (TDS) was assessed as a nondestructive evaluation technique for aircraft composites. Material properties of glass fiber composite were measured using both transmission and reflection configuration. The interaction of THz with a glass fiber composite was then analyzed, including the effects of scattering, absorption, and the index of refraction, as well as effective medium approximations. THz TDS, in both transmission and reflection configuration, was used to study composite damage, including voids, delaminations, mechanical damage, and heat damage. Measurement of the material properties on samples with localized heat damage showed that burning did not change the refractive …
Investigation Of The Platinum-Rich Portion Of The Platinum-Tantalum Phase Diagram, Bob Dean Browning
Investigation Of The Platinum-Rich Portion Of The Platinum-Tantalum Phase Diagram, Bob Dean Browning
Theses and Dissertations
The Pt-Ta binary system was investigated at two isotherms;1000°C and 1500°C, and at eleven alloy compositions in the range of 50 to 100 atomic percent platinum. The alloys were examined by x-ray diffraction and metallography. Three intermetallic compounds, Pt2Ta, Pt3Ta, and Pt4Ta were found to exist in this composition range. The Pt4Ta intermetallic appeared only at the 1500°C isotherm. Platinum dissolved tantalum substitutionally to 90 atomic percent at 1500 °C and to approximately 80 atomic percent at 1000 °C.