Engineering Commons^™

The Interaction Of The Cotton Piece With The Piles Of The Scrabble Cotton Drum, Fazliddin Egamberdiev, Ilkhom Abbazov, Oybek Kholmuratov, Rashid Kaldybaev

Technical science and innovation

This article presents the results of an analytical study of the process of loosening and cleaning raw cotton from small debris by pileging working bodies of purifiers, on the basis of which directions for further research were chosen to optimize the parameters of the developed pile drum with spherical piles and rubber strips. Cotton entering production contains impurities. The processes of loosening and cleaning the fiber shreds are key in the initial stages of ginning, as they prepare the raw cotton for ginning and directly affect the reliability, productivity of these processes and the quality of the resulting fiber. Weed …

Advances In Cellulose Nanomaterial-Based Foams For Environmental Applications, Md Musfiqur Rahman

Electronic Theses and Dissertations

The use of metal-oxide nanoparticles adsorbents is limited to fixed-bed columns in industrial-scale water treatment applications. This limitation is commonly attributed to the tendency of nanoparticles to aggregate, the use of non-sustainable and inefficient polymeric resins as supporting materials, or a lack of adsorption capacity. Foams and aerogels derived from cellulose nanomaterials have unique characteristics, such as high porosity and low density, which enables their use in a variety of environmental applications, including water treatment. However, the overall use of cellulose nanomaterial-based foams in various environmental sectors is limited due to the high cost of production associated with time- and …

Code To Combustion: Cnc Rotor Replication Using Cam, Luis Luna

Publications and Research

In the current landscape, computer-aided design (CAD) and computer numerical control (CNC) technologies have greatly enhanced manufacturing processes, allowing rapid and high-precision production. This project will focus on recreating a Wankel engine rotor, using SolidWorks for design and Mastercam for Computer-Aided Manufacturing (CAM) simulations. The process begins with SolidWorks, which is used for a template of a high-precision rotor model. Mastercam is then utilized for the CAM programming, allowing for the creation of intricate tool paths and tool usage simulations. This approach is vital for complex objects like the Wankel engine rotor, which demands high precision. The primary objective of …

Slitter Blade Sharpener, Griffin Buchan, Regan Lane, Kinsale Sproule

Mechanical Engineering

Within this document, our team, “Think Sharpener”, will discuss the following work we have completed since the Critical Design Review: material and part procurement, the manufacturing process for our prototype, and a discussion of our results from testing our final Verification Prototype (VP). To summarize our team’s work during the last portion of this project, our design for the slitter blade sharpening mechanism required us to consult the IME department for materials and manufacturing guidance, order pneumatic components from various online hardware companies, and test our VP to verify we met the engineering design specifications. Our slitter blade sharpening mechanism …

A Two-Diameter Helical Endmill Beam Model For Tool Tip Dynamics Prediction With Application To Milling, Emma D. Betters

Doctoral Dissertations

The aim of this dissertation is to describe the dynamic response of helical endmill geometries to enable the use of receptance coupling substructure analysis (RCSA) to predict the tool tip vibration response of arbitrary tool-holder-spindle-machine combinations. The tool tip vibration response, or receptance, is a key input for milling stability prediction. Currently, a measurement is required to determine the tool tip receptance for each tool-holder-spindle-machine combination, which may not be possible in production environments. In the RCSA approach, the spindle receptances are measured once and archived, while the tool and holder are modeled. Tool tip receptances are predicted by analytically …

Additively Manufactured Nature Inspired Morphology For Redesign: Advancing Next Generation Energy Systems, Vanshika Singh

Doctoral Dissertations

To meet cleaner energy goals and increasing demand, energy systems such as gas turbines and power plants are required to be operated under harsh loading conditions like higher temperatures and pressures, fluctuating loads, and corrosive environments. Advanced manufacturing techniques such as additive manufacturing (AM) have put us on the trajectory for next-generation system designs, allowing complex geometries and high-temperature alloys with tailored material properties. We need new and systematic design philosophies to use AM's unique characteristics prudently. For a given functionality, nature tends to provide similar solutions in animate and inanimate structures. We propose to take inspiration from nature's repetitive …

Thermal Resistance Characterization Of High-Voltage Sic Power Module, Landon Lemmons

Mechanical Engineering Undergraduate Honors Theses

Researchers within the University of Arkansas Electrical Engineering Research Department have embarked on a project aimed at enhancing the thermal performance of high-voltage power modules. To aid in the progress of this project, the design, and development of a thermal tester device are needed. The primary objective of this device is to determine the various thermal properties of high-voltage power modules that the electrical engineering department has developed. Additionally, the project aims to facilitate electrical loading tests on power modules and provide researchers with the means to calibrate the power module in terms of thermal load. This project also possesses …

Synergistic Strategies In Sinter-Based Material Extrusion (Mex) 3d Printing Of Copper: Process Development, Product Design, Predictive Maps And Models., Kameswara Pavan Kumar Ajjarapu

Electronic Theses and Dissertations

3D printing pure copper with high electrical conductivity and exceptional density has long been challenging. While laser-based additive manufacturing technologies suffered due to copper's highly reflective nature towards laser beams, parts printed via binder-assisted technologies failed to reach over 90% IACS (International Annealed Copper Standard), electrical conductivity. Although promising techniques such as binder jetting, filament, and pellet-based 3D printing that can print copper exist, they however still face difficulties in achieving both high sintered densities and electrical conductivity values. This is due to a lack of comprehensive understanding of property evolution from green to sintered states and the strategies that …

Analyzing The Effects Of Ultrafast Laser Processing On Mechanical Properties Of 3d-Printed Pla Parts, Darshan Pramodbhai Yadav

Theses and Dissertations

Recent advances in additive manufacturing technologies have already led to wide-scale adoption of 3D-printed parts in various industries. The expansion in choice of materials that can be processed, particularly using Fused Deposition Modeling (FDM), and the steady advancements in dimensional accuracy control have extended the range of applications far beyond rapid prototyping. However, additive manufacturing still has considerable limitations compared to traditional and subtractive manufacturing processes. This work addresses limitations associated with the as-deposited surface roughness of 3D-printed parts. The effects of roughness-induced stress concentrations were studied on ultimate tensile strength and fatigue life. The samples were manufactured using a …

Damage Detection With An Integrated Smart Composite Using A Magnetostriction-Based Nondestructive Evaluation Method: Integrating Machine Learning For Prediction, Christopher Nelon

All Dissertations

The development of composite materials for structural components necessitates methods for evaluating and characterizing their damage states after encountering loading conditions. Laminates fabricated from carbon fiber reinforced polymers (CFRPs) are lightweight alternatives to metallic plates; thus, their usage has increased in performance industries such as aerospace and automotive. Additive manufacturing (AM) has experienced a similar growth as composite material inclusion because of its advantages over traditional manufacturing methods. Fabrication with composite laminates and additive manufacturing, specifically fused filament fabrication (fused deposition modeling), requires material to be placed layer-by-layer. If adjacent plies/layers lose adhesion during fabrication or operational usage, the strength …

Temperature Gradient Effect On Solid-Liqid Interface Properties Of Al-Cu Alloy: A Molecular Dynamics Study, Prashant Kumar Jha

All Theses

Aluminum-copper (Al-Cu) alloys are widely used in the aerospace industry due to their favorable strength-to-weight ratio, good fatigue resistance, and corrosion resistance. These properties make Al-Cu alloys an excellent choice for aircraft structural components that require high strength and low weight. Additive manufacturing (AM), also known as 3D printing, has emerged as a promising processing method for Al-Cu alloys in aerospace manufacturing. AM enables the production of lightweight optimized geometries difficult to manufacture through conventional subtractive methods. AM also reduces material waste by only depositing material where needed in the part geometry. The rapid solidification conditions in AM processes motivate …

Modular Composite Sandwich Structures For Thermal And Structural Retrofitting Of Existing Buildings, Marc Al Ghazal

Masters Theses

Around 40% of global energy consumption and 30% of worldwide carbon dioxide (CO2) emissions are attributed to buildings. Most of this consumption is dedicated to ensuring thermal comfort. The goal of this research was to develop and field validate retrofit solutions to improve the energy efficiency of buildings. Exterior cladding panels were designed and tested to ensure adequate thermal and structural performance. Sandwich panels (glass fibers reinforced polymer (GFRP) skins and polymeric foam cores) were fabricated using the vacuum assisted resin transfer molding (VARTM) process. Extruded polystyrene (XPS) and polyurethane (PU) foams were compared as core materials through a series …

Tagalong Trail, Sean Wahl, Jason Davis, Quinlan Stephens, Ryan Johnson, Vinh Vo

Mechanical Engineering

The Cal Poly mechanical engineering team working on the Path of Lights and Sounds for the Girl Scouts of California’s Central Coast has now completed their project. In the last quarter of their project, they were able to finalize their tile’s structural design while iterating through several electronics board designs. Through this iteration, they were able to create a final electronics board and designed a water-resistant enclosure to house the board. A new team member was added, allowing them to manufacture 28 tile structures and 30 electronics assemblies over the course of two and a half weeks. This proved to …

Cnc Retrofits, Fabian Samano, Murat Askin, Daniel Lonczak, Zane Campise

Mechanical Engineering

The Boxford CNC Lathe is a machine used for educational purposes. The goal of the CNC Retrofits project is to improve the Boxford MT2’s performance and functionality to enable Mr. Lonczak to manufacture customized ballpoint pens. Within this Final Design Review (FDR) document, we present design updates since the CDR and implementation/assembly techniques. This work culminates in a solution to Mr. Lonczak’s needs which is analyzed in three subsystems: main control, spindle position tracking, and user interface. Within this report, we show the results of each subsystem’s verification process. These results prove that the design concept was met by describing …

Laser Assisted Direct Writing Of Liquid Metal For Microprinting Applications, Olga Vargas Cruz

Theses and Dissertations

This paper presents a research study for potential printing of a Liquid Metal (LM) Eutectic Gallium Indium alloy (EGaIn) through the applications of the innovative additive manufacturing technology LIFT (Laser Induced Forward Transfer). LIFT is a precise printing technology that allows to create small, detailed printing. The liquid metal in study, EGaIn, has demonstrated great potential for microelectronics applications due to its minimum toxicity and high conductivity. Throughout this research different printing parameters are studied to comprehend the behavior of EGaIn printing with LIFT technique, these include laser energy, laser pulse, receiver material substrate, donor layer thickness, and …

Kwad - Ksu All Weather Autonomous Drone, Nick Farinacci, Sebastian Gomez, Stewart Baker, Ed Sheridan

Symposium of Student Scholars

"KWAD" or "KSU all-Weather Autonomous Drone" project was sponsored by Ultool, LLC to the KSU Research and Service Foundation to create a lightweight drone capable of capturing HD video during all-weather operations. The conditions of all-weather operation include rainfall of one inch per hour and wind speeds of up to twenty miles per hour. In addition, a global minimum structural safety factor of two is required to ensure the system's integrity in extreme weather conditions. Potential mission profiles include autonomous aerial delivery, topological mapping in high moisture areas, security surveillance, search and rescue operations, emergency transportation of medical supplies, and …

Micro And Nano R2r Embossing Of Extruded Polymers, Raymond S. Frenkel

Doctoral Dissertations

This dissertation presents a process for directly imprinting or embossing extruded polymers as an advancement in roll-to-roll (R2R) embossing methods that avoids the problems of converting preformed films, increases throughput, and reduces costs. A proof-of-concept R2R apparatus was designed and constructed for directly embossing extruded polymer, and experimental results were evaluated. This laboratory scale R2R apparatus employed a thin metal ribbon belt mold with micro or nano scale features in a calendering setup, with a close coupled induction heating (IH) coil to preheat the ribbon mold above glass transition temperature (T_g) of the polymer, prior to contact with …

An Investigation Into The Challenges Of Contemporary Additive Manufacturing: Insights Into The Metallurgical Response Of Materials And Relevant Solution, Huan Ding

LSU Doctoral Dissertations

Additive Manufacturing (AM) has gained attention in recent years due to its unique capabilities in the fabrication of complex parts. As with any new research, there is still a lack of sufficient understanding in the field of additive manufacturing, and further investigation is needed to solve existing problems. Ultimately, the aim is to enable the widespread use of AM components across various industries.

Chapter One provides a brief introduction to the background and current bottlenecks of additive manufacturing technology. Chapter two focuses on the development of high-strength 7075 aluminum alloy (Al7075) for Fused Deposition Modeling and Sintering (FDMS) technology. Al7075 …

Additive Manufacturing For Medical Education, Michael Noon

College of Engineering Summer Undergraduate Research Program

A growing body of evidence is suggesting that anatomical knowledge, the keystone of many medical specialties, is suffering among new graduates. While a host of reasons are provided, one common thread that many point to is the decline of cadaver dissections in the classroom. Many virtual audio-visual tools are used to address this gap, yet evidence has shown their ineffectiveness. Given this gap, the high degree of flexibility found in additive manufacturing (AM), and the many uses AM has already found in the medical field, we propose its use to fill this gap, allowing for students to learn with touch …

Numerical Study Of Solar Receiver Tube With Modified Surface Roughness For Enhanced And Selective Absorptivity In Concentrated Solar Power Tower, Shawn Hatcher, Mathew Z. Farias, Jianzhi Li, Peiwen Li, Ben Xu

Manufacturing & Industrial Engineering Faculty Publications and Presentations

Concentrated solar power (CSP) is a reliable renewable energy source that is progressively lowering its cost of energy. However, the heat loss due to reflected and emitted radiation hinders the maximum achievable thermal efficiency for solar receiver tubes on the solar tower. Current solar selective coatings cannot withstand the high temperatures that come with state-of-the-art CSP towers often needing to be recoated soon after initial operation. We intend to use Inconel 718 with different additive manufacturing (AM) practices to construct surfaces that allow for more light-trapping to occur. By adjusting printing parameters, we can tailor a surface to allow for …

Wire Deflection Investigation During Wedm Of Aisi 304 Stainless Steel: An Experimental And Numerical Study, Sara A. El-Bahloul, Mohamed G. Elkhateeb

Mansoura Engineering Journal

Wire electrical discharge machining (WEDM) is a specific form of electrical discharge machining that employs a small diameter wire electrode to cut a narrow kerf in the workpiece. Since the wire deflection has a negative effect on the performed cutting, this research seeks to study the resultant wire deflection during WEDM of AISI 304 stainless steel. This study is performed with the help of three types of modeling; namely, mathematical modeling, experimental modeling, and thermo-mechanical finite element modeling. The mathematical modeling is performed to analyze the stresses and the wire lag, while the experimental modeling is achieved to observe the …

Investigating The Effect Of Bead Geometry On Fiber Orientation And Thermomechanical Properties For Large-Format Extrusion-Based Additive Manufacturing, Joanna F. Keaton

Electronic Theses and Dissertations

In large-format extrusion-based additive manufacturing of polymer composites, the relationship between material properties and processing parameters requires further investigation. This thesis focuses on the relationship between fiber orientation and thermomechanical properties for short fiber-filled thermoplastic polymer systems manufactured by extrusion-based additive manufacturing. Fiber orientation is particularly important in determining the thermomechanical properties of the composite material as properties in the direction of deposition are expected to be higher for highly aligned fibers than randomly aligned fibers. Fiber orientation distribution, which is related to processing parameters and deposition conditions, can be efficiently represented by the orientation tensor. The orientation tensor can …

Mechanical Characterization Of Automated Fiber Placement And Additive Manufacturing Hybrid Composites, Lucan Haviland

Electronic Theses and Dissertations

This thesis presents the optimization of processing parameters based on the mechanical properties of Continuous Fiber-Reinforced Thermoplastic (CFRTP) Unidirectional (UD) consolidated tapes. The UD tapes were consolidated using an AFP head and a thermoforming press for comparison. The adhesive strength of hybrid parts consisting of CFRTP UD tape bonded to a 3D-printed substrate with the same matrix system were investigated. Large Area Additive Manufacturing (LAAM) was utilized for the 3D-printed parts. Different types of thermoplastic composite materials were explored, including Glass Fiber reinforced Polyethylene Terephthalate Glycol (GF/PETG), Carbon Fiber reinforced Polyethylene Terephthalate Glycol (CF/PETG), Carbon Fiber reinforced Polycarbonate (CF/PC), and …

Effects Of Machining Parameters Of C45 Steel Applying Vegetable Lubricant With Minimum Quantity Cooling Lubrication (Mqcl), Mayur A. Makhesana, Prashant J. Bagga, Kaushik M. Patel, Jaime Taha-Tijerina

Informatics and Engineering Systems Faculty Publications and Presentations

One of the most significant performance indicators for measuring the machinability of materials is tool wear and surface roughness. Choosing the best combination of cutting parameters can help reduce production costs, which is what the manufacturing industry is interested in. At the same time, industries are always looking for an alternative to conventional flood cooling since its use creates an environmental burden and health concerns for the operators. Therefore, vegetable oil-based minimum quantity cooling lubrication (MQCL) is considered a cutting environment. Sunflower oil is utilized as base fluid in MQCL and applied to the cutting zone through a nozzle. The …

Additive Manufacturing Of High-Performance Nanolamellar Eutectic High-Entropy Alloys, Jie Ren

Doctoral Dissertations

Additive manufacturing, also called three-dimensional (3D) printing, is an emerging technology for printing net-shaped components layer by layer for applications in automotive, aerospace, biomedical and other industries. In addition to the vast design freedom offered by this approach, metal 3D printing via laser powder-bed fusion (L-PBF) involves large temperature gradients and rapid cooling and provides exciting opportunities for producing microstructures and mechanical properties beyond those achievable by conventional processing routes. Although these extreme printing conditions enable microstructural refinement to the nanoscale for achieving high strength. However, high-strength nanostructured alloys by laser additive manufacturing often suffer from limited ductility. Eutectic high-entropy …

Spall Characteristics Of Additively Manufactured Stainless Steel, Kevin Lamb

Doctoral Dissertations

Additive manufacturing (AM) has rapidly transformed from a novelty prototyping technology into a growing sector of production across a wide range of industries. Much work has been documented in literature to demonstrate the behavior of AM products under static and quasi-static loading conditions. However, the behavior of AM materials under high strain rate loading is not as well understood. This research attempts to advance the fundamental knowledge of the relationship between the unique aspects of AM and the mechanical performance under high velocity impact loading conditions.

This project examines the behavior of AM 316L stainless steel (SS) exposed to high …

Life Cycle Energy Assesment Of Advanced Fiber Reinforced Composite Design And Manufacturing Methodologies, Urjit Lad

All Theses

Automotive industry at large is focused on vehicle light-weighting since a 6%-8% increase in fuel efficiency can be achieved with a 10% reduction in vehicle weight [1]. With the growing demand for cost-effective and sustainable light weighting of automobile structures, interest has increased in the application of fiber reinforced plastic (FRP) composites for use in the Body-in-White (BiW), which can account for up to 40% of the total vehicle weight. Traditional FRP composite manufacturing processes like vacuum assisted resin transfer molding, autoclave consolidation or use of automated fiber placement have been successfully used for marine and aerospace applications. However, these …

Fatigue And Fracture Of Electron Beam Melting Ti-6al-4v, William A. Grell

Electronic Theses and Dissertations

For applications in the aerospace field, selection of materials for a given design requires an understanding of critical properties, like fatigue and fracture, in addition to static mechanical and physical properties. With the ongoing advancements in metallic additive manufacturing techniques and the interest in applying the process to aerospace applications, there is a clear need to fully characterize properties. Arguably, the most attractive alloy for applications in aerospace is the Ti-6Al-4V alloy. The current dissertation examines the mechanical properties of the alloy, made by the Electron Beam Melting (EBM) Powder Bed Fusion (PBF) method. As illustrated in this work, the …

Laser-Induced Forward Transfer (Lift) Based Bioprinting Of The Collagen I With Retina Photoreceptor Cells, Md Shakil Arman, Ben Xu, Andrew Tsin, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications and Presentations

This study focuses on the 3D bioprinting of retina photoreceptor cells using a laser-induced forward transfer (LIFT) based bioprinting system. Bioprinting has a great potential to mimic and regenerate the human organoid system, and the LIFT technique has emerged as an efficient method for high-resolution micropatterning and microfabrication of biomaterials and cells due to its capability of creating precise, controlled microdroplets. In this study, the parameters for an effective femtosecond laser-based LIFT process for 3D bioprinting of collagen biomaterial were studied. Different concentrations of collagen I solutions were tested and 0.75 mg/ml to 1 mg/ml collagen Ⅰ was identified as …

Developing Control System For Manufacturing Processes, Md Shahriar Forhad

Theses and Dissertations

Process control has been a critical component in today's manufacturing industry. Industrialists nowadays want reliable control to assure precision manufacturing. Modern control systems must be more dynamic, so that any needed modifications may be made quickly to accomplish the desired product change. For innovative research and development, system customization is critical to ensure freedom for experimental works. In addition, full control of manufacturing systems is necessary to realize and implement Industry 4.0. Often, it is difficult to achieve such control due to limited access to proprietary equipment. To this end, this thesis focuses on developing a custom control platform for …