Engineering Commons^™

Production Of A Banjo: Development Of Manufacturing Processes For Banjo Resonators,Rims, And Necks., Kevin N. Zollinger

Undergraduate Honors Theses

This body of research focused on the development of prototype tooling and manufacturing processes to produce resonators, rims, and necks for building banjos. The resulting fixtures and manufacturing processes were designed for ease of use by a single employee in a small shop environment. This research required proficiency in interdisciplinary mediums (ie. 2D modeling, 3D modeling, centerline tool path program generation, 2D modeling, 3D modeling, rendering, design, and woodworking).

The resonator required development of a matching set of forming surfaces, a bending/gluing fixture, a work-holding fixture for utilizing a wood lathe, and a steam chamber required for bending strips of …

Best Practices Using Building Information Modeling In Commercial Construction, Simon Beveridge

Theses and Dissertations

There has been an increase in adoption of building information modeling (BIM) by commercial contractors over the past few years but there is not a clear indication of current application or the frequency of each use. This research was undertaken to determine the frequency and best practices of using BIM in commercial construction. Leading commercial contracting firms were contacted and employees were selected to complete a telephone survey that was designed to determine how they are using BIM. It was found that BIM is being used with more frequency on projects, with plans to continue to implement it even further …

Strider: Manufacturing Processes, Michael Warren-Angelucci

Industrial and Manufacturing Engineering

The goal of the Strider Project is to create a mobility device that can support a person with weakened leg strength and enable them to be supported and maintain a standing position. A prototype of the Strider was created by three Mechanical Engineering students as their senior project. The topic of this senior project was to analyze and create a manufacturing process for the manufacture of the Strider that will be ergonomic and cost effective.

There were many things that needed to be accomplished in order to create the manufacturing process. The first step was to verify that the prototype …

Integration Of Process Parameter Control And Digital Image Correlation Methods In An Investigation Of The Variability Of Marine Polymer Matrix Composite Material Properties, Keith Andrew Berube

Electronic Theses and Dissertations

The very nature of continuous fiber composite materials, with their heterogeneous structure of layered and interwoven fibers bound together by a polymer resin matrix, lead to an inevitable variability in mechanical properties. This is especially true if the fabrication process is not well controlled. Unlike fabricating components with metals, where the properties of the material are known beforehand, the final properties of the composite material are determined during the process of fabricating the composite part. The research described herein was undertaken to better enable the use of polymer matrix composites in the marine construction industry by developing a knowledge base …

Handitrike - Recumbent Tricycle, Sean Higginson, Kevin Howie, Vinay Patel

Mechanical Engineering

This report covers the design and construction of the recumbent racing tricycle for Mr. Robert T. Kelly, a disabled veteran. Unfortunately Rob’s right leg is five inches shorter than his left one and therefore is unable to properly operate standard cranks. Our team HandiTrike is composed of Sean Higginson, Kevin Howie, and Vinay Patel and our project requires us to come up with a design that is feasible to complete within the given three quarters, as well as allow Rob to gain full use of his tricycle. Currently Rob ‘s trike uses the standard crank set up found on most …

Solar Turbines Creep Test Fixture, Rene Maciel, Eric Nelson, Chris Ewald

Mechanical Engineering

No abstract provided.

Formula Sae Turbocharger Engine Development, Eric Griess, Kevin Mccutcheon, Matthew Roberts, William Chan

Mechanical Engineering

This project, Formula SAE Turbocharger System Development, was sponsored by the Cal Poly, San Luis Obispo Formula SAE team. The team proposed this project in order to have a powerful yet lightweight engine so they can be extremely competitive at their competition. The baseline output of the single cylinder 450cc engine (2006 Yamaha WR450F) was 46 horsepower and 27 ft-lb of torque. The goal of this project was to increase the output of that engine to 60 horsepower and 35 ft-lb through the use of a turbocharger.

Chsr Clothing: How To Start A Small Business Clothing Line To Be Run Efficiently With Minimum Capital And Maximum Profit, Kayvon Banisalam

Industrial and Manufacturing Engineering

Executive Summary

Many clothing brands have failed because they did not design marketable products with a suitable business plan. Often times, clothing brand owners do not use the capital they possess in efficient ways. They can get caught off guard with unexpected costs and are not running the business in the most resourceful and professional way.

The goal of this project is to create a clothing brand that portrays distinctive designs to go along with an effective business model. This includes implementing decision analysis at several points of the planning phase, along with quality and cost controls. Creating quality products …

Design And Manufacture Of Natural Composite Canoe, Derek Baptista

Industrial and Manufacturing Engineering

Abstract

This report looks into the application and feasibility of manufacturing natural composite canoes. The main fabrics that were analyzed are flax, hemp, and jute. These were then compared to carbon fiber and fiberglass to see the difference in mechanical properties. It was found that the natural fibers have lower mechanical properties but that this could be overcome by designing a balsa wood core with ribs running up the walls. After manufacturing a hemp canoe, many lesson were learned and areas of interest were further explored. With the use of different natural fibers, these canoes can greatly reduce the carbon …

Process Improvements For Establishing Cmmi Certification At Company Xyz, Megan Farrell

Industrial and Manufacturing Engineering

CMMI stands for Capability Maturity Model Integration and is an enterprise-wide Process-Improvement model that provides a set of best practices that addresses productivity, performance, costs, and stakeholder satisfaction. This improvement model is generally used in computer software companied and not only does it improve their processes, but many contracts will only be awarded with those companies who are CMMI certified, so it is very important for Company XYZ. This goal of this project was to help improve the CMMI efforts at Company XYZ in 4 of the 20 distinct processes areas to attain a CMMI Maturity Level of 3. Improvement …

Facilities Planning For An Aerospace Manufacturing Company, William Petrossi

Industrial and Manufacturing Engineering

Absolute Technologies Inc. (ATI) has been growing for years, and is running out of space at their current manufacturing facility in Yorba Linda, CA. ATI will be moving to a much larger facility this winter. They are looking for an efficient way to utilize this space. The machine positions were taken as fixed, seeing as a lean expert was brought in to give advice on placement. With the machines fixed, the scope was narrowed to other areas.

A systematic approach to facilities design is utilized. First, a goal needs to be defined. The goal is to reduce the time wasted …

Consolidation Of Company Abc, Estelle Sillari-Owen

Industrial and Manufacturing Engineering

This project aims to solve Company ABC’s issues in order to keep the company afloat and to keep the company profitable. This was done by reducing Company ABC’s organizational and inventory build-up issues. The project aims to reduce the company’s dependence on outside storage, with plans of consistent inventory reduction over the next year. An implementation plan was created to ensure the company keeps on track to increase profits and prevent against increasing inventory costs.

Wolfpack Gear Inc. Composite Frame Firefighter Backpack, Gabriel Mountjoy, Blair Ridings, Carl Drummond Buchenroth

Mechanical Engineering

No abstract provided.

Warehouse Redesign, Cristine Carmel Dewar

Industrial and Manufacturing Engineering

A young, growing biomedical company is expanding its warehouse space to keep up with the increasing production. This project’s goals were to recommend a layout and improve a process that would minimize the distance traveled by the material handlers, increase the safety of the warehouse by implementing visual controls, implement ergonomics to reduce chance of injury, and save money for the company. To achieve this first I familiarized myself with their current processes and department and the space required for their current and future production levels. Next I created two alternative layouts, the first (Layout A) to minimize distance and …

Friction Stir Spot Welding Of Ultra-High Strength Steel, Trent J. Hartman

Theses and Dissertations

Friction stir spot welding (FSSW) is quickly becoming a method of interest for welding of high strength steel (HSS) and ultra high strength steel (UHSS). FSSW has been shown to produce high quality welds in these materials, without the drawbacks associated with fusion welding. Tool grade for polycrystalline cubic boron nitride (PCBN) tools has a significant impact on wear resistance, weld quality, and tool failure in FSSW of DP 980 steel sheet. More specifically, for a nominal composition of 90% CBN, the grain size has a significant impact on the wear resistance of the tool. A-type tools performed the best, …

Remanufacturing Cleaning Process Evaluation, Comparison And Planning, Ozan Yagar

Theses and Dissertations - UTB/UTPA

This thesis aims to combine previous research on remanufacturing cleaning processes and applications into a single decision-making tool, in the form of software, which a remanufacturer can use to find a cleaning system that matches their specific demands. This thesis will provide an in-depth review of each cleaning process, the chemicals used in those processes, and the contamination types for which they were developed. This research also provides evaluation and comparison that assists remanufacturers in designing their cleaning systems. Finally, there will be a description and demonstration of the software. The ultimate goal is to find correct cleaning process to …

A Case Study For Financial Feasibility Of Automated Costing Support In A Small Machine Shop, Benito A. Gonzalez

Theses and Dissertations - UTB/UTPA

A knowledge-based cost estimating expert system is chosen by a Mexican machine shop. Differences between the traditional experience-based system employed and the automated system are studied. Data is gathered to analyze time effectiveness, accuracy and payback of the software. Data from seventy part models is recorded to study the time experiment, and data from fifty part models is used to study the accuracy and consistency. Data is analyzed by calculating mean, standard deviation, and test of hypothesis. The results indicate that the software is faster than the traditional quoting system; however, the payback point is high. Also, results show the …

A Comparative Study Of Strength And Stiffness Of Thin-Walled Specimens Fabricated By Fdm And 3d Printing Technologies, Miranda Rodrigo

Theses and Dissertations

Rapid Prototyped part failure constitutes a major issue for both RP providers and customers. When parts fail the reputation of the vendor is heavily deteriorated, customer dissatisfaction increase and replacement of the broken parts is often necessary to avoid the loss of future business. Product design teams often run into situations where Rapid Prototyped parts are not able to withstand shipping and handling and delivered broken or while demonstrating and examining the parts. When done in the face of customers this builds a perception of poor quality and lack of aptitude on the design group as well as the RP …

Design, Construction, And Evaluation Of An Automated Chicken Coop Door, Kyle Inks

BioResource and Agricultural Engineering

This senior project takes a look into the design, construction, and evaluation of an automated chicken coop door. The idea and need for such a door came from my mother Jan Inks. The parameters for the project include, low production cost, easy installation on existing coops, sleek design, automatically open at a set time in the morning, and automatically close at a set time in the evening.

Recreational Nordic Sit Ski, Mathew Bissonnette, Johnathon Gorski, Kevin Izumiya

Mechanical Engineering

The purpose of this project was to design, build, and test a recreational Nordic sit ski for use by Disabled Sports Eastern Sierra. The goal was to improve adjustability and reduce weight compared to previous sit ski designs. The project was completed by Cal Poly Mechanical Engineering seniors Mathew Bissonnette, Johnathon Gorski, and Kevin Izumiya. Kinesiology seniors Harpreet Saini and Carl Anderson provided discipline support and disability etiquette training.

The project was sponsored by the National Science Foundation Research to Aid Persons with Disabilities (RAPD) grant. The grant was proposed by and awarded to Dr. Brian Self and Dr. James …

Formula Hybrid Drivetrain Design, Zachary (Zak) Mcfarland, Alex Pruitt, William Domhart

Mechanical Engineering

The Formula Hybrid senior project group was tasked with designing and building a drivetrain system for the Cal Poly Society of Automotive Engineers (SAE) Formula Hybrid (FHSAE) team. FHSAE gave customer requirements for performance and geometry for the drivetrain and the FHSAE rulebook has guidelines regarding safety requirements. The team chose to compete in the electric category of the 2012 FHSAE competition. After getting feedback from previous car performance and researching different powertrain options, the senior project team arrived at three conceptual ideas. Using a quality function deployment method, the senior project team chose the concept where two motors independently …

The Hovering Ball Exhibit, Matthew Bauzon, Will Lennox, Michelle Swan

Mechanical Engineering

No abstract provided.

Design Of An Independent Star-Clip Organizer (Iso), Christopher Gonzales, Greg Lovasik, Daniel Silveira

Mechanical Engineering

Discussed below is a new concept to sort and deliver star clips for flight deck safety net manufacturing. Multiple methods were generated, along with the necessary research, and were narrowed down to a single concept: the tray-loading preprocess design, named ISO (Independent Star-Clip Organizer). The overall design has been finalized and designed. Due to budget constraints, an actual prototype was not built. However, the design of such a prototype is described by this report, backed with calculations and experimental testing.

Human Powered Helicopter: Rotor Structure, Joseph Ram, Juan Carlos Olvera

Mechanical Engineering

The following report encompasses the Human Powered Helicopter Rotor Team’s conceptual models and ideas based on research and modeling analysis. The following gives an overview of material researched, concept generation, analyzation, manufacturing, and testing for a rotor structure to be installed in a Human Powered Helicopter.

Advanced Design Optimization For Composite Structure: Stress Reduction, Weight Decrease And Manufacturing Cost Savings, Shayan Ahmadian

Master's Theses

An injection moldable chopped fiber composite actuator with detailed drawing and tolerances was designed within one year. A vendor was selected and a quote for injection molding tooling cost for production was obtained and the first prototype was built in addition of six months. The risks are identified and material characterization tests are proposed.

The objective of this project was redesigning an aluminum made actuator with a continuous fiber composite for weight saving purposes. After searching the literature and consulting with experts in the field it was concluded that manufacturing costs associated with continuous fiber composite are 3 times as …

High Speed Friction Stir Spot Welding On Dp 980 Steel:Joint Properties And Tool Wear, Nathan David Saunders

Theses and Dissertations

With the desire to improve passenger safety and fuel efficiency, Ultra High Strength Steels (UHSS) have been developed for use in the automotive industry. UHSS are high strength steels with high ductility and strength. DP 980 is one of these UHSS being applied in automobile manufacturing. DP 980 is difficult to join with Resistance Spot Welding (RSW) because of the high carbon content and alloying in this material. The weld becomes brittle when it solidifies during the welding process. With the desire and motivation of widely using UHSS, new welding processes are needed to be developed in order to effectively …

Lunalight Project: Solar-Rechargeable Led Lantern And Cell Phone Charger, Sean C. Dawson, Michael E. Deagen, Francisco N. Dye, Brian S. Mircheff, Ryan O. Ramelb

Materials Engineering

Today, 1.6 billion people in the world do not have access to grid electricity. Villagers living off the grid in developing nations resort to kerosene lanterns to light their homes. The fumes from burning kerosene are toxic and lead to respiratory illnesses over time. Our sponsor, OneMillionLights, plans to help people to escape poverty by providing them with a clean source of light at night. Children that must work in the fields during the day can use a solar-rechargeable lantern at night to read or study, and street vendors can use the lanterns at night to improve their businesses.

The …

Feasibility Analysis For Electrically-Powered Hoverboard, Cameron Chan, Jason Cortez, Jay Lopez

Aerospace Engineering

Composite materials are engineered by combining two or more constituent materials with significantly different physical or chemical properties in such a way that the constituents are still distinguishable, and not fully blended. Due to today’s high rising prices of gasoline and aviation fuel costs, many manufacturers have turned to the use of lightweight composites in their designs due to the advantages of the composite material, which include outstanding strength, excellent durability, high heat resistance, and significant weight reduction that the composite material properties hold. The purpose of this project is to design and construct a composite structure for an electrically-powered …

The Design And Fabrication Of A Microfluidic Reactor For Synthesis Of Cadmium Selenide Quantum Dots Using Silicon And Glass Substrates, Peter Robert Gonsalves

Master's Theses

A microfluidic reactor for synthesizing cadmium selenide (CdSe) quantum dots (QDs) was synthesized out of a silicon wafer and Pyrex glass. Microfabrication techniques were used to etch channels into the silicon wafer. Holes were wet-drilled into the Pyrex glass using a diamond-tip drill bit. The Pyrex wafer was anodically bonded to the etched silicon wafer to enclose the microfluidic reactor. Conditions for anodic bonding were created by exposing the stacked substrates to 300V at ~350oC under 5.46N of force. A syringe containing a room temperature CdSe solution was interfaced to the microfluidic reactor by using Poly (dimethylsiloxane) (PDMS) as an …

Transport Phenomena Associated With Liquid Metal Flow Over Topographically Modified Surfaces, Wen Liu

Theses and Dissertations--Mechanical Engineering

Brazing and soldering, as advanced manufacturing processes, are of significant importance to industrial applications. It is widely accepted that joining by brazing or soldering is possible if a liquid metal wets the solids to be joined. Wetting, hence spreading and capillary action of liquid metal (often called filler) is of significant importance. Good wetting is required to distribute liquid metal over/between the substrate materials for a successful bonding.

Topographically altered surfaces have been used to exploit novel wetting phenomena and associated capillary actions, such as imbibitions (a penetration of a liquid front over/through a rough, patterned surface). Modification of surface …