Engineering Commons^™

Improving Technology For Producing Complex Fertilizer From Low-Grade Phosphorites Of The Central Kyzylkum, A.Zh. Allamuratova, A.U. Erkaev, A.M. Reimov, Saparbay Kazakhbaev, Dilshodbek Kurbiyazov

Chemical Technology, Control and Management

The methods of nitric acid processing of phosphate raw materials are analyzed. A technology has been developed for the nitric acid processing of phosphate raw materials into nitrogen-phosphorus fertilizer with the implementation of the process in a condensed pulp by adding sulfuric acid. A technology for producing complex fertilizers with a wide range of N:P₂O₅:K₂O ratios with improved physico-chemical parameters due to the introduction of various potassium salts into the process is proposed.

Synthesis Of Local Control Systems For Underwater Units Cleaning Bottom Sediments In Reservoirs, Yuriy Gennadiyevich Shipulin, Zebiniso Akmalovna Zayniddinova

Chemical Technology, Control and Management

The article discusses the issues of synthesizing local control systems for underwater units for cleaning bottom sediments in reservoirs. It is shown that the protection and rational use of natural reservoirs and the fight against their premature siltation is becoming an urgent task.

It is proposed to use small-sized underwater units, consisting of information and measuring devices, to carry out search work for cleaning bottom sediments under water; control systems; actuators and means of communication with humans.

It is shown that the task of controlling the loading of an underwater unit (UU) requires maintaining optimal performance while simultaneously taking into …

Modernization Of Water Flow Measurement In Open Irrigation Systems Using The Slope-Area Method, R.M. Aliev, Djalilov Anvar

Chemical Technology, Control and Management

This article describes two methods for determining water flow in open irrigation systems: “speed - area” and “slope - area”. The authors considered the problem of its modernization using the existing method for determining water flow “slope - area” in open irrigation systems. The essence of the issue is the remote transfer of parameters necessary for calculating water flow in open irrigation systems and improving the means of their processing. In scientific studies conducted by the authors, the required hydraulic parameters were studied using the “slope - area” and “speed - area” water flow methods. Based on experimentally obtained data, …

Synthesis Algorithm Of Control System Based On Neural Network For The Gas And Oil Process, Jasur Sevinov, Abdishukurov Maqsudovich Shavkat, A.Z. Shodiyorov

Chemical Technology, Control and Management

Automatic control systems in the oil and gas processing are considered. After extraction of natural gas condensate, management of technological parameters plays an important role in its processing. Among the parameter of regulating algorithms, control based on neural network technology was considered. These control systems are created on the basis of algorithms of neural network technology. There are several structures of neural networks according to their structure. Differences in the process of information processing of these branching structures are considered.

Dynamic Characteristics Of Magnetoelectric Linear Actuators Of Control Systems, Мakhmudjon Muxamedovich Аbdullayev, Rasul Ernazar Ogli Abdiev

Chemical Technology, Control and Management

This paper presents the results of studies carried out on magnetoelectric drives that carry out linear movement, models of drives are built and, on their basis, studies of the main indicators associated with the movement of a linear armature are carried out, such as: speed of movement, acceleration, current values, voltage and traction force of the armature. Also presented are the results of a study of magnetoelectric linear motion drives based on an analysis of graphs of their dynamic characteristics.

Algorithms For Structural Synthesis Of Control Systems For Dynamic Objects Under Conditions Of Unmeasurable Disturbances, Husan Zakirovich Igamberdiev, Uktam Farkhodovich Mamirov, Bunyod Mamurjon Ugli Buronov

Chemical Technology, Control and Management

The paper talks about ways to use inverse dynamic models to structure a control system for moving objects when disturbances are not measured. To solve the main problems that arise when implementing the inverse dynamic model method, methods for synthesizing inverse systems with given dynamic characteristics are used. The solution to this problem is obtained based on the theory that dynamic observers are invariant to unmeasured input influences. We broke down the matrix operator on the right into elementary orthogonal rotation matrices and on the left into permutation matrices to get a stable answer to the equation of the current …

Artificial Neural Network Based Grain Moisture Measuring Device, Erkin Eljaev, Shohrux Nurali O‘G‘Li Narzullayev, Elyor Faxriddinovich Khudoyberdiev

Chemical Technology, Control and Management

To date, the intellectualization of solving technical issues in managing, controlling, and measuring technological processes in all branches of industrial production is considered an urgent task. In this regard, a class of intelligent devices and sensors has emerged. Intelligent devices and sensors differ from their analog counterparts in that they have functions such as automatic adjustment of the measurement range, self-calibration, data processing, and decision-making. The article discusses the development of intelligent measuring instruments based on a capacitive transducer for measuring the moisture content of grain and grain products.

Results Of Experimental Study Of Solar Collector Efficiency, Shakhnoza Sultanova, Ajargul Mambetsheripova, Jasur Safarov

Chemical Technology, Control and Management

The article considers the influence of ambient temperature on the drying efficiency depending on the incident solar radiation, changes in the average temperature of the absorber plate depending on the absorbed power, as well as the thermal efficiency of the collector at significant values of coolant flow.

Strategy For Predictive Control Of The Rectification Process Based On A Model Controller With A Given Forecast, Ildar Rafkatovich Sultanov

Chemical Technology, Control and Management

A method is being developed to optimize the generated controls for the multicomponent distillation process with prediction, based on predictive data with a moving horizon. The difference between this method and the classical modeling approach, in which the percentage of the degree of opening of valves installed on the output streams of the column is used as control actions, is that control occurs on the feedback principle. The proposed method is based on the use of a dynamic process model to optimize control actions in real time in order to achieve certain production targets. The essence of the MPC approach …

Identification Of Faults In Highways Using Approximation Methods And Algorithms, Khudayberdiyev Khakkulmirzayevich Mirzaakbar, Anvar Asatilloyevich Ravshanov

Chemical Technology, Control and Management

Many fast Fourier transforms are used to identify defective parts of uneven surfaces on roads and send information to relevant organizations on the road, using the " RAVON YO‘LLAR" application installed on a mobile device during car movement. We determine the uneven parts of the road. Smooth and well-maintained roads reduce the risk of vehicle collisions, skidding and other road-related incidents. Timely measures contribute to overall safety, comfort and economic efficiency.

Synthesize A Neural Network Parameter Optimizer For An Adaptive Pid Controller, Nashvandova Gulruxsor Murot Qizi

Chemical Technology, Control and Management

Wide application of proportional-integral-differential (PID)-regulator in industry requires constant improvement of methods of its parameters superstructuring. In the paper, the questions of optimization of PID-regulator parameters with application of methods of neural network technology are considered. A methodology for selecting the architecture of neural network optimizer designed to determine the tuned parameters of PID regulator is proposed. The algorithm of training of the neural network, with the set on the basis of the method of inverse gradient propagation is offered. The proposed improved PID-neural regulator allowed to provide stabilization of neural network operation and its trainability in the control loop …

Development Of A Criterion Assessing The Level Of Relationship Of Multiple Identified Characteristics For Classification, Mirzoyan Mirzaaxmedovich Kamilov, Oybek Zokirovich Koraboshev, Bobomurod Mamitjonovich Tojiboev

Chemical Technology, Control and Management

This article discusses an optimized version of the standard design developed by Yu.I.Zhuravlev, an optimization procedure through an algebraic approach based on precedent algorithms that solves the problem of pattern identification. The formation of the convex hull of the recognition operator and corrective procedures of information models by mutual compensation of each other was also studied. In addition, the functional connection of recognition operators and the definition of idempotent connection of operators are analyzed.

Analytical-Critical Review Of Widely Used Industrial Devices For Drying Mineral Fertilizers, Djalolitdin Paxritdinovich Mukhitdinov, Aleksey Viktorovich Schulz

Chemical Technology, Control and Management

The article is devoted to the review of the modern state of research in the mineral fertilizers drying field, critical analysis and comparison of widely used drying apparatuses. There are procedures of preliminary equipment selection for soluble fertilizers industrial drying on the basis of such criteria as productivity, efficiency, energy saving, environmental impact degree, indicating the possible advantages and disadvantages of different application variants.

Chromatographic Analysis Of The Chemical Composition Of Pyrolysis Distillate, Sh.T. Juraev, B.F. Muxiddinov, U.T. Tailakov

Chemical Technology, Control and Management

The paper presents the results of a study of the physico-chemical characteristics of the liquid fraction of products of thermal oxidative pyrolysis of worn tires. The mass fraction of the volatile gas compounds, the optimal boiling points of the obtained condensates and the flashpoint of pyrolysis liquids, together with the mass composition of cracking products of rubber products at high-temperature pyrolysis at a temperature of 800-900 °C, were determined. Chromatographic analysis allowed us to determine the composition, mainly the mass composition of pyrolysis products, which consisted of carbon (42.8%), higher aliphatic and aromatic hydrocarbons (17.0%), methane (10.2%), benzene (4.2%) and …

A Neural Network Model For Monitoring And Forecasting The Process Of Storing Oilseeds, N.A. Kabulov

Chemical Technology, Control and Management

The paper presents the results of research on the control, forecasting and management of the storage process of oilseeds. Vegetable oil production and energy consumption are two important factors of oilseed storage systems. The first ones should meet the needs of the population quantitatively and qualitatively. As a result, in order to properly control these two important aspects, it is necessary to maintain an appropriate microclimatic environment using a computational decision support system (DSS) that is able to adapt to changes in environmental characteristics. The multilayer perceptron neural network (MLP-NN) was developed to simulate the temperature and relative humidity profiles …

Calculation Of Hydraulic Resistance Of A Tubular-Gridse Nozzle With Spiral Turbulizers, Nurmukhamedov Habibulla Sagdullaevich, Mavlonov Elbek Tulkinovich, S.Kh. Nishonova, Kh.S. Nurmukhamedov

Chemical Technology, Control and Management

The article presents the results of an experimental study on the hydraulic resistance of a tubular-grid nozzle made of smooth pipes and pipes with spiral turbulators. Experiments were carried out with nozzles made of smooth pipes and pipes with turbulators. Spiral turbulators are placed discretely with a step t/d=0,3125-0,9375 and installed on a tube sheet in a checkerboard pattern with a step s/d=1,15-10. Experimental studies were carried out with air flow in the transition region.

It has been established that with increasing numerical values of the dimensionless parameter s/d, the resistance of the pipe package decreases from 1,3 to 1,8 …

The Use Of Ultraviolet Radiation As A Means Of Destroying Microorganisms In Cherries, Jasur Safarov, Shaxnoza Sultanova, Pulatov M. Murodjon

Chemical Technology, Control and Management

The article discusses methods for extending the shelf life of cherries, having previously treated it with an ultraviolet ray. The article also presents the results obtained, which prove that the shelf life of cherries exposed to ultraviolet increases. At the same time, the article describes in detail the processing technique and presents the results of research.

Study Of Dynamic Characteristics Of The Mechanical Circuit Of The Developed Induction Inertial Vibration Transducer, Sulton Fayzullayevich Amirov, Asror Abdunabiyevich Shoimkulov

Chemical Technology, Control and Management

The article examines the dynamic characteristics of the mechanical circuit of the developed induction vibration transducer. It is found that in the investigated transducers forced oscillations occur with the frequency of the input disturbing force, the amplitude of forced oscillations does not depend on the initial conditions and time, and in forced oscillations with damping there is always a shift of the oscillation phase compared to the phase of the input disturbing force. It is shown that the induction vibration transducer reproduces the measured vibrations with small distortions only in a relatively narrow frequency region at frequencies of the input …

Mathematical Models And Calculation Of Parameters Of Optoelectronic Angular Displacement Converters, Yuriy Gennadyevich Shipulin, Azimjon Khusanov

Chemical Technology, Control and Management

The article discusses promising optoelectronic converters (OP) for wide application of angular movements. A methodology and diagram for calculating OP with the transverse movement of a moving element is presented; in order to simplify the calculation, the weight range of angular movements is conventionally divided into three sub ranges. A graph is given of the dependence of the area of the photosensitive surface of a photo resistor made from a single crystal of high-resistivity p-type silicon.

Improvement Of Calorimetric Quality Analyzers For Substances, Makhfuza Azimovna Radjabova

Chemical Technology, Control and Management

It is noted that the development of intelligent means of measuring qualitative indices is of topical importance. Since the quality of many substances is determined by optical methods, an algorithm for spectrophotometric data processing has been developed, which consists of primary data processing (stage I) and determination of qualitative indices of liquid products (stage II). Since the task of numerical determination of colour characteristics of transmittance coefficients of liquid samples is incorrectly set, it is recommended to use regularization methods of A.N.Tikhonov to improve metrological characteristics of the device. On the basis of regularization methods for solving incorrect problems, algorithms …

Application Of Quantum Algorithms In The Synthesis Of Dynamic Objects, Noilakhon Yakubova

Chemical Technology, Control and Management

Around the world, the food industry is focusing on achieving energy and resource efficiency. One of the main challenges in the field of process automation is the creation of effective control systems using intelligent technologies to improve the quality of processes and achieve the production of high-quality products with less energy and resources. Therefore, it is necessary to work with a large amount of data. Particular attention is paid to the development of computational algorithms for automated high-speed computational analysis systems for processing this data at high speed. Therefore, the article discusses the use of quantum computing methods in controlling …

System For Advanced Control Of Thermal Parameters Of Glass Furnaces, O'Tkir Xolmanov

Chemical Technology, Control and Management

The results of an analysis of the functioning of glass furnaces for melting semi-white or discolored glass as an object of automatic control and management are presented. Through experimental research, a parametric control scheme for a glass melting furnace was formed and a system for improved control of thermal glass melting processes was synthesized. The proposed system regulates the parameters of a furnace with a horseshoe-shaped flame development. Based on commercially produced instruments and automation equipment that ensure stabilization of thermal conditions of glass melting. The burner block control algorithm provides control over the performance of the gas burner, safety …

Intelligent Decision Support System, Khurshid Salim Ugli Turayev

Chemical Technology, Control and Management

The article studies issues related to the development of intelligent systems located in an environment capable of perceiving this environment and acting autonomously to achieve assigned tasks. To create an intelligent process control system, it is necessary to monitor the mode to ensure high quality of finished products with minimal energy consumption at a given productivity of the entire complex. It is important to have a flow of input data to provide the system with operational information to support decision making.

The proposed intelligent control system makes it possible to analyze the results of production activities to make organizational and …

Life Cycle Management Of A Technological Complex For Separating Multicomponent Mixtures Under Conditions Of Uncertainty Of Parameters, Yusuf Shodievich Avazov

Chemical Technology, Control and Management

The issue of control the lifecycle of technological complexes of multicomponent mixtures is considered, taking into account the uncertainty of parameters. Among uncertainties such as parameter uncertainty, model uncertainty, choice uncertainty under variability, spatial variability uncertainty, temporal variability uncertainty, inter-site variability uncertainty, more attention is paid to input parameter uncertainty and action uncertainty. The rectification technology is schematically presented, the influence of parameter uncertainty on the technological functions of the rectification complex. The scheme analyzes the control and assessment of “uncertainty” to repeat the lifecycle of the rectification complex and make changes to the components of the rectification complex technology. …

Improvements Of The Control System For The Technological Process Of Drying Bulk Materials, Azizbek Nodirbekovich, Dilmurod Ikromovich

Chemical Technology, Control and Management

The issues of convective drying of bulk materials as objects of monitoring, control and advanced management are presented based on the results of simulation modeling of a complex heat and mass transfer process, taking into account the drying kinetics. As a result of the work of a number of them, in the last few decades neat hypotheses were formed about moisture migration in and around dried materials, which led to the creation of accurate mathematical models of drying behavior, with successfully applied in a wide range of fields. The reasons for this are the dynamics of processes in the drying …

Dependence Of The Granulometric Composition Of Chalk During Granulation In A Turbulized Layer, N.A. Annaev, S.Kh. Nurmukhamedov, Zh.V. Sultonov, N.Sh. Khudoiberdieva

Chemical Technology, Control and Management

The article presents the results of an experimental study on chalk granulation in the turbulized layer of a turboblade granulator. The design of the apparatus combines the following sequential processes: grinding, granulating and compacting newly formed granules. In addition, this device has the ability to carry out both rotational and reciprocating motion. It has been established that preliminary grinding of the feedstock increases the efficiency of the granulation process and improves the quality of the finished product. In the experiments, four substances were used to create 2 astringent suspensions and the optimal combination and their ratios were determined. The experiments …

The Algorithm For The Design Of Fine Granular Substances’ Smart-Type Heat And Moisture Converters Based On Their Accuracy And Speed Criteria, Erkin Uljaev, Ali Abduakhatovich Abduraxmanov

Chemical Technology, Control and Management

The paper describes a technique and algorithm allowing to perform parametric design of smart-type heat and moisture converters (hereinafter SHMC) of fine-grained dispersive materials based on their criteria of accuracy and speed. The proposed algorithm optimizes the process of design of smart-type switches and ensure optimal performance of the switches. The method of calculation and selection of optimal parameters of smart-type heat and moisture converters intended to be used in the measurement of parameters such as heat and humidity of fine dispersive substances are aimed at boosting two parameters, i.e., the accuracy and speed. Also, the design stages have been …

Algorithm For The Functioning Of The Robot's Mechatronic System, Nodira Batirdjanovna Alimova, Bekmurod Bayotovich Yusupov

Chemical Technology, Control and Management

Currently, the introduction of mechatronics and robotics into modern technologies, including rural industry, which are based on different types of mechatronic modules, is relevant. The article discusses the functioning algorithm of the electro-pneumatic multi-position mechatronic system of an intelligent robot. The mechatronic system under consideration is an integrated complex of electro-pneumatic elements, electronic elements and computer technology, with constant dynamic changes in energy and information between them, united by a common automatic control system. The main distinctive feature of this mechatronic system is increased positioning accuracy and high traction forces.

Development Of An Imitation Model Of The Vulcanization Process In The Production Of Elastomeric Composites, Toshtemir Avezov, Mirxalil Agzamovich Ismailov

Chemical Technology, Control and Management

In the article, a systematic approach to the mathematical modeling of the production process of complex multi-stage elastomeric composites was considered, which allows to take into account the stoichiometric relationship of the chemical reaction in the process. Based on the chemical reaction occurring in the mixer, a kinetic model of the elastomer composites production process is proposed, which is the basis for obtaining the main functional relationship of the mathematical model for the mixer, the main quality indicator of the process. The proposed systematic approach in the form of a mathematical model based on the stoichiometric relationship and the …

Trends In The Development And Improvement Of Glass Furnaces And Monitoring And Control Systems, N.R Yusupbekov, O'Tkir U. Xolmanov

Chemical Technology, Control and Management

The theory and practice of establishing industrial automation systems for glass furnaces and installations as they are right now are taken into consideration. Comparative analysis is based on publications over the last 20 years in the field being studied. On the basis of an analysis of the review materials, generalizations are made that form the basis for proposals aimed at modernizing and improving the technology and instrumentation of fuel combustion processes in gas-burning furnaces and installations, as well as monitoring and control systems for technological processes occurring in glass furnaces and installations.