Engineering Commons^™

Effect Of Citric Acid On Slump, Compressive Strength, And Setting Time Of Belitic Calcium Sulfoaluminate Concrete, Israel Aguilar Rosero

Graduate Theses and Dissertations

Belitic calcium sulfoaluminate (BCSA) cement has well established advantages related to fast setting time, fast strength gain, long-term strengths, shrinkage, and sustainability. Due to its fast setting and hardening, this type of cement has historically been used to repair concrete structures, highways, and runways. This work provides much needed guidance on establishing mix design criteria for BCSA cement. Guidance is also given on the effects of set retarders on strength, slump, and setting times. Citric acid and a phosphonic acid-based admixture were tested as retarders for different concrete mixtures. Three studies were performed. In the slump study five different water …

Projecting Water Available For Irrigation Use And Identifying Water Supply Stress Under Climate Change Scenarios In Selected U.S. Fruit And Vegetable Production Regions, Andrew Shaw

Graduate Theses and Dissertations

Climate change affects water resources differently across geospatial regions in the United States (U.S). There is a concern of how water availability will be affected by changes in long-term temperature and precipitation patterns, specifically in major production regions for eight fruit and vegetable crops. The effects on surface water available for irrigation use and supply stress in five regions containing 31 Agricultural Statistics Districts (ASDs) were assessed. The Water Supply Stress Index Model was used and modified to project water available for irrigation use across nine climate scenarios driven by historical data, five General Circulation Models, two population scenarios, and …

Development Of Vs Profiles And Site Periods In The Mexico City Basin, Landon Joel Woodfield

Graduate Theses and Dissertations

This study presents dynamic site characterization measurements at 25 sites within the Mexico City Basin. The primary focus of the testing was along the western edge of the Mexico City Basin. At each site, active source Multi-channel Analysis of Surface Waves (MASW) arrays and passive source Microtremor Array Measurements (MAM) L-arrays and circular arrays were used to acquire dispersion data. Horizontal to Vertical Spectral Ratio (HVSR) data was collected to determine site periods at each location. These experimental dispersion data and site periods were fit using a joint inversion of Rayleigh and Love wave dispersion data and HVSR site period …

The Release, Transport, And Utilization Of Phosphorus From Bed-Sediments: A Study Of A Eutrophic Littoral Cove On Beaver Lake In Northwest Arkansas, James A. Mccarty

Graduate Theses and Dissertations

Eutrophication of surface waters not only impacts the environment but also water treatment processes, the most significant of which is from the effects of algae. During peak algal growth in many southern U.S. reservoirs, inflows that bring nutrients are at an annual minimum, and phosphorus released from bed-sediments is trapped in the hypolimnion. Littoral areas, described as the most productive zone of the lake, may be a possible source of phosphorus that fuels algal growth in the reservoir. I studied an isolated shallow cove in the War Eagle Creek arm of Beaver Lake in Northwest Arkansas to measure, quantify, and …

Surface Modified Polypropylene Membranes For Treating Hydraulic Fracturing Produced Waters By Membrane Distillation, Tharaka Hawpe Gamage

Graduate Theses and Dissertations

Membrane distillation is an emerging technology for treating hydraulic fracturing flowback and produced waters. Suppression of membrane fouling by inorganic and polar and non-polar organic compounds is a challenge. Here polyhydroxyethyl methacrylate, polyacrylic acid, polvinylallyl imidazolium bromide and polyvinylhexyl imidazolium bromide chains have been grafted from the membrane surface. Fouling is initially due to adsorption of organic compounds followed by scale formation. When challenged with produced water, membranes modified with polvinylallyl imidazolium bromide chains provided the greatest resistance to fouling. For EC pretreated produced water and synthetic produced water that contained mainly inorganic species, the flux decline was much less.

Irrigation Design In Montana: Accommodating Varying Water Accessibility Across The Continental Divide., John Garrett Lampson

Biological and Agricultural Engineering Undergraduate Honors Theses

The design work performed in this project was conducted over two summers (2018, 2019) of internship experience with the Natural Resources Conservation Service (NRCS) across the state of Montana. The first summer’s design work was based out of Glendive, MT, in Dawson County, approximately 50 kilometers from the North Dakota border. The second summer was in Missoula, MT, in Missoula County, near the Idaho border. The two areas differ significantly in topography, weather, and water availability with the main separating geographic influence being the Rocky Mountains.

This paper focuses on the design process and requirements for two farms located outside …

Design Of A Shallow-Aero Ebb And Flow Hydroponics System And Associated Educational Module For Tri Cycle Farms, Julie Halveland

Biological and Agricultural Engineering Undergraduate Honors Theses

Tri Cycle Farms, whose main mission is to reduce food insecurity in their community, is a non- profit urban farm in Fayetteville, Arkansas. The “Tri” in their name refers to the three parts of their foundation: giving a third of their yield to volunteers, giving a third to local food pantries, and selling a third to sustain the farm and demonstrate the economy of local food production. They want to expand on the third part and have a vision of building a hydroponic greenhouse with the intention that it will create more crops to sell and give, as well as …

Utilization Of Recycled Filament For 3d Printing For Consumer Goods, Alexa Peterson

Apparel Merchandising and Product Development Undergraduate Honors Theses

The 3D printing market has been used in a wide variety of manufacturing industries including textile and apparel. Many consumers can now own a personal 3D printer at home for recreational printing. There are even websites dedicated to 3D printing patterns made by consumers. However, the materials used in the 3D printing process pose a problem for the environment due to their plastic-based nature. 3D printing is a layered process with each layer being printed depending on the layer below it for strength and stability. During the 3D printing process, great amounts of waste are produced as a result of …