Engineering Commons^™

The Umass Experimental X-Band Radar (Umaxx): An Upgrade Of The Casa Ma-1 To Support Cross-Polarization Measurements, Jezabel Vilardell Sanchez

Masters Theses

Ground-based radars are instruments commonly used to surveil the precipitation climate of the surrounding areas. Weather events are characterized by collecting backscatter data and analyzing computed products such as the Reflectivity Factor, the Doppler Velocity, the Spectrum Width, the Differential Reflectivity, the Co-polar Correlation Coefficient and the Differential Propagation Phase. The ability of the radar to transmit different polarization waves, such as horizontal and vertical polarization, allow for further analysis of the weather given the capability to perform co-polar and cross-polar measurements. The Linear Depolarization Ratio is another computed product based on the difference in power between the co-polarized and …

Estimating Electromagnetic Emissions From A Site Installation With Multiple Racks Of Server Equipment, Ze Sun

Masters Theses

“There are hundreds, sometimes even thousands, of servers working simultaneously inside a data center. Their radiation can be a problem and cause EMI issues. However, it is not feasible to perform full-wave simulation of these racks because of the large electric size of the model. In this thesis, an algorithm is proposed to predict the emission form rack array. The equivalent dipole source is extracted from EMI measurement data of a single rack and used as the radiation source in the multiple rack model. The coupling between racks cannot be ignored, but through the simulation, it is also found that …

Unified Probe Launch Pattern Design And Methodology Of Differential Probe Characterization, Han Deng

Masters Theses

"Differential probe is wildly used in the signal integrity area to do the accuracy signal measurement in frequency domain or time domain. Comparing with traditional SMA connector measurement, the probe measurement has several advantages such as the high flexibility and measurement efficiency. Nevertheless, the probe has some disadvantages such as multiple design patterns and the difficulty of fast landing. In this thesis, a unified probe landing pattern is provided to solve the con of probes and a probe testing fixture is designed for characterize probe and extract the probe model.

In the first portion, a unified differential probe launching pattern …

Experimental Characterization Of Common-Mode Sources For Prediction Of System Level Common-Mode Current On Cable Harnesses, Sameer Sudha Arun Walunj

Masters Theses

"Common-mode current on cable harnesses is often the primary source of radiated emissions below several hundred megahertz. It is difficult, however, to estimate common-mode currents that will occur in a system from component level tests because the common-mode impedances are different in the system. Research presents two methods for using simple component level tests to estimate equivalent common-mode source voltages and source impedances responsible for generating common-mode current. Key to these methods is assuming the harness can be represented with two transmission lines, one terminated with a short and one with an open. Equivalent sources are predicted for those circuits …

Coupling Path Visualization Based On Reciprocity Theorem, Yang Zhong

Masters Theses

"A new method to visualize coupling path is proposed to help solve EMI problems. Based on the reciprocity theorem and the concept of reaction, coupling coefficient (CC) is defined to characterize coupling power density. For two-port networks, surface integral of CC can represent coupled voltage on the open-circuited port or coupled power on the loaded port. For dipole-moment based systems, surface integral of CC can represent coupled field components. The calculated CC should be a complex scalar at each point. By properly adjusting the excitation phases, the imaginary part of surface integral of CC will be zero and thus can …

Passively-Coded Embedded Microwave Sensors For Materials Characterization And Structural Health Monitoring (Shm), Katelyn Rose Brinker

Masters Theses

"Monitoring and maintaining civil, space, and aerospace infrastructure is an ongoing critical problem facing our nation. As new complex materials and structures, such as multilayer composites and inflatable habitats, become ubiquitous, performing inspection of their structural integrity becomes even more challenging. Thus, novel nondestructive testing (NDT) methods are needed. Chipless RFID is a relatively new technology that has the potential to address these needs. Chipless RFID tags have the advantage of being wireless and passive, meaning that they do not require a power source or an electronic chip. They can also be used in a variety of sensing applications including …

Near-Field Scanning Based Shielding Effectiveness Extraction For Board Level Shielding Cans, Harsh Shrivastav

Masters Theses

"The conventional definition of shielding effectiveness is well suited for calculating electromagnetic shielding in the far-field. However, in the near field, shielding effectiveness calculation is not so straight forward. In radio frequency interference problems, most of the field coupling occurs in near field. Having a well-defined method to calculate near-field shielding effectiveness is important for estimating the suppression of radio frequency interference using the shield cans. In this research, a method to extract the shielding effectiveness of board level shielding cans using near field scanning is developed. Shielding effectiveness is defined by modelling the shielded noise source as equivalent dipole …

Microwave Detection Of Surface Breaking Cracks In Metallic Structures Under Heavy Corrosion And Paint, John Robert Gallion

Masters Theses

"We live in the world of "aging infrastructures". In this environment, critical and heavily utilized infrastructure, i.e. ships, planes, bridges, etc., are operating at or beyond their designed age. Replacement is no longer an option and "retirement for cause" is the current approach to maintenance and replacement. Consequently, there is an ever-increasing demand for efficient and robust nondestructive evaluation (NDE) methods that can determine the physical health of these structures. Large structures, which are primarily made of metals, either steel or aluminum, are susceptible to high-stress cracking and corrosion. Stress-induced cracks in heavily corroded steel, used in bridges, railroads, storage …

Practical Methods For Source Separation In Emc Measurements, Yuanzhuo Liu

Masters Theses

"Electromagnetic emission is critical in the electronic industry with the rapid growth of the development of the electronic device. To identify the emission from the multipule sources, two methods are proposed in the near field scan and total radiated power measurement respectively.

The first method can be applied in the measurement of the field generated by multiple non-correlated sources. The contribution of each source is determined using a blind source separation (BSS) technique. The measurements are performed using one scanning probe and stationary reference probes, avoiding the need to measure the spatial correlations of the random field. The resolving result …