Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 5 of 5
Full-Text Articles in Engineering
Vibration-Based Health Monitoring Of Multiple-Stage Gear Train And Differential Planetary Transmission Involving Teeth Damage And Backlash Nonlinearity, Andrew Patrick Sommer
Vibration-Based Health Monitoring Of Multiple-Stage Gear Train And Differential Planetary Transmission Involving Teeth Damage And Backlash Nonlinearity, Andrew Patrick Sommer
Master's Theses
The objective of this thesis is to develop vibration-based fault detection strategies for on-line condition monitoring of gear transmission systems. The study divides the thesis into three sections. First of all, the local stresses created by a root fatigue crack on a pinion spur gear are analyzed using a quasi-static finite element model and non-linear contact mechanics simulation. Backlash between gear teeth which is essential to provide better lubrication on tooth surfaces and to eliminate interference is included as a defect and a necessary part of transmission design. The second section is dedicated to fixed axis power trains. Torsional vibration …
Development Of A Cubesat Instrument For Microgravity Particle Damper Performance Analysis, John Trevor Abel
Development Of A Cubesat Instrument For Microgravity Particle Damper Performance Analysis, John Trevor Abel
Master's Theses
Spacecraft pointing accuracy and structural longevity requirements often necessitate auxiliary vibration dissipation mechanisms. However, temperature sensitivity and material degradation limit the effectiveness of traditional damping techniques in space. Robust particle damping technology offers a potential solution, driving the need for microgravity characterization. A 1U cubesat satellite presents a low cost, low risk platform for the acquisition of data needed for this evaluation, but severely restricts available mass, volume, power and bandwidth resources. This paper details the development of an instrument subject to these constraints that is capable of capturing high resolution frequency response measurements of highly nonlinear particle damper dynamics.
Structure Climbing Monkey Robot, Paul Bessent
Structure Climbing Monkey Robot, Paul Bessent
Master's Theses
This report describes the design, building, and testing of the Structure Climbing Monkey Robot (SCMR). It is composed of seven successive joints and linkages with two grippers at the two ends. Each gripper can act as the base or the end of the robot. The SCMR has the ability to climb any structure. The gripper plates can be changed to grab different kinds of structures, but this one is made to grab 2x4‘s. A program was written to assist the user to grab four non-coplanar, non-orthogonal points.
The SCMR is actuated by a total of nine motors: two to open …
Geomagnetic Compensation For Low-Cost Crash Avoidance Project, John C. Torres
Geomagnetic Compensation For Low-Cost Crash Avoidance Project, John C. Torres
Master's Theses
The goal of this work was to compensate for the effects of the Earth’s magnetic field in a vector field magnetic sensor. The magnetic sensor is a part of a low-cost crash avoidance system by Stephane Roussel where the magnetic sensor was used to detect cars passing when it was mounted to a test vehicle. However, the magnetic sensor’s output voltage varied when it changed orientation with respect to the Earth’s magnetic field. This limited the previous work to only analyze detection rates when the test vehicle travelled a single heading. Since one of the goals of this system is …
High-Resolution, Non-Contact Angular Measurement System For Psa/Rsa, Ronald D. Sloat
High-Resolution, Non-Contact Angular Measurement System For Psa/Rsa, Ronald D. Sloat
Master's Theses
A non-contact angular measurement system for Pitch Static Attitude (PSA) and Roll Static Attitude (RSA) of hard disk drive sliders is designed and built. Real-time sampling at over 15 KHz is achieved with accuracy of +/- 0.05 degrees over a range of approximately 2-3 degrees. Measuring the PSA and RSA is critical for hard drive manufacturers to control and improve the quality and reliability of hard drives. Although the hard drive industry is able to measure the PSA and RSA at the subassembly level at this time, there is no system available that is able to measure PSA/RSA at the …