Engineering Commons^™

Design, Fabrication And Characterization Of Zero Power Sensor/Harvester For Smart Grid Applications, Zeynel Guler

Mechanical Engineering ETDs

This study presents a flexible sensor/harvester device to be used in both electromagnetic sensing and energy harvesting applications for smart grids. When a current passes through a wire, the sensor detects the magnetic field created by that current. The sensor magnet interacts with the wire magnetic field resulting in a transfer of energy through the piezoelectric cantilever. Piezoelectric, conductive, magnetic, and magnetostrictive composite thin films were prepared to fabricate this device.

Initially, the magnet of the cantilever was optimized considering its shape, thickness, length, taper angle etc. via both simulations and experiments. Peak to peak voltage versus cantilever position graph …

Improved Methodology For Conducted Emi Assessment Of Power Electronics And Line Impedance Measurement, Mark Anthony Didat

Theses and Dissertations

Electromagnetic Interference (EMI), primarily common mode (CM), is problematic in a wide range of electronic circuits due to its propensity to radiate, particularly in high power applications. It is routine for much effort and resources to be dedicated to its characterization and reduction as EMI compliance is a requirement for most electronic systems and devices, including power electronics. Many well-known factors contribute to a system’s EMI performance including intentional coupling from system components as well as unintentional coupling from parasitics. Sources of intentional coupling may include Y-capacitors intended to mitigate EMI as part of a filter. Unintentional coupling is more …

Static And Dynamic State Estimation Applications In Power Systems Protection And Control Engineering, Ibukunoluwa Olayemi Korede

Doctoral Dissertations

The developed methodologies are proposed to serve as support for control centers and fault analysis engineers. These approaches provide a dependable and effective means of pinpointing and resolving faults, which ultimately enhances power grid reliability. The algorithm uses the Least Absolute Value (LAV) method to estimate the augmented states of the PCB, enabling supervisory monitoring of the system. In addition, the application of statistical analysis based on projection statistics of the system Jacobian as a virtual sensor to detect faults on transmission lines. This approach is particularly valuable for detecting anomalies in transmission line data, such as bad data or …

Fourier Analysis And Optimization Of Inductive Wireless Power Transfer For Electric Vehicle Charging, Andrew P. Foote

Doctoral Dissertations

With the growth of electric vehicle (EV) popularity, different charging options to increase user convenience and reduce charging time such as high power wireless charging are increasingly being developed and researched. Inductive wireless power transfer (WPT) systems for EVs must meet specifications such as stray field, battery power and voltage operating range, efficiency, and ground clearance. The coil geometry and design have a large impact in meeting these constraints. Typical design approaches include iterative analysis of predetermined coil geometries to identify candidates that meet these constraints.

This work instead directly generates WPT coil shapes and magnetic fields to meet specifications …

Enhancing Power System Flexibility Through Efficient Integration Of Facts And Electric Vehicles, Izaz Zunnurain

Open Access Theses & Dissertations

The global transition towards a cleaner and sustainable energy landscape has led to the integration of renewable energy sources and electric vehicles (EVs) into the modern power system, along with their complexities. Due to the high penetration of renewable energy sources and rapid growth of EVs, the power grid often experiences congestion, increasing the overall operating cost of the power system and directly jeopardizing the power stability and quality of the grid. A flexible and resilient power infrastructure that can accommodate the intermittency of renewable energy sources and the adoption of EVs is very much required to ensure the reliability …

Development Of Metaheuristic Algorithms For The Efficient Allocation Of Power Flow Control Devices, Eduardo Jose Castillo Fatule

Open Access Theses & Dissertations

No abstract provided.

A Modular Framework For Surface-Embedded Actuation And Optical Sensing In Soft Robots., Paul Bupe Jr

Electronic Theses and Dissertations

This dissertation explores the development and integration of modular technologies in soft robotics, with a focus on the OptiGap sensor system. OptiGap serves as a simple, flexible, cost-effective solution for real-time sensing of bending and deformation, validated through simulation and experimentation. Working as part of an emerging category of soft robotics called Soft, Curved, Reconfigurable, Anisotropic Mechanisms, or SCRAMs, this research also introduces the Thermally-Activated SCRAM Limb (TASL) technology, which employs shape-memory alloy (SMA) wire embedded in curved sheets for surface actuation and served as the initial inspiration for OptiGap. In addition, the EneGate system is presented as a complementary …

Use Of Digital Twins To Mitigate Communication Failures In Microgrids, Andrew Eggebeen

Theses and Dissertations

This work investigates digital twin (DT) applications for electric power system (EPS) resilience. A novel DT architecture is proposed consisting of a physical twin, a virtual twin, an intelligent agent, and data communications. Requirements for the virtual twin are identified. Guidelines are provided for generating, capturing, and storing data to train the intelligent agent. The relationship between the DT development process and an existing controller hardware-in-the-loop (CHIL) process is discussed. To demonstrate the proposed DT architecture and development process, a DT for a battery energy storage system (BESS) is created based on the simulation of an industrial nanogrid. The creation …

Electrical Characteristics Of In-House Produced Micro/Nanodielectrics, Dewan Mahmudullah

<strong> Theses and Dissertations </strong>

Dielectric characterization is very important across a wide range of applications, including the design and optimization of capacitors, electrical insulation, and electronic devices. It plays a vital role in providing valuable insights for material selection, performance evaluation, and the development of advanced dielectrics. The permittivity of dielectrics is a fundamental property of dielectric materials that quantifies their ability to store and dissipate energy in the presence of an electric field. Studies for developing advanced dielectrics and accurate measurements of the dielectric constant are essential for understanding and optimizing the performance of various electrical and electronic systems. The objective of this …

A Design Strategy To Improve Machine Learning Resiliency Of Physically Unclonable Functions Using Modulus Process, Yuqiu Jiang

Theses and Dissertations

Physically unclonable functions (PUFs) are hardware security primitives that utilize non-reproducible manufacturing variations to provide device-specific challenge-response pairs (CRPs). Such primitives are desirable for applications such as communication and intellectual property protection. PUFs have been gaining considerable interest from both the academic and industrial communities because of their simplicity and stability. However, many recent studies have exposed PUFs to machine-learning (ML) modeling attacks. To improve the resilience of a system to general ML attacks instead of a specific ML technique, a common solution is to improve the complexity of the system. Structures, such as XOR-PUFs, can significantly increase the nonlinearity …

Ism-Band Energy Harvesting Wireless Sensor Node, Fnu Naveed

Graduate Theses and Dissertations

In recent years, the interest in remote wireless sensor networks has grown significantly, particularly with the rapid advancements in Internet of Things (IoT) technology. These networks find diverse applications, from inventory tracking to environmental monitoring. In remote areas where grid access is unavailable, wireless sensors are commonly powered by batteries, which imposes a constraint on their lifespan. However, with the emergence of wireless energy harvesting technologies, there is a transformative potential in addressing the power challenges faced by these sensors. By harnessing energy from the surrounding environment, such as solar, thermal, vibrational, or RF sources, these sensors can potentially operate …

Diverse Impacts Of Commercial Ev Charging Load Infrastructure On Electric Power Grid, Antonio Avila

Open Access Theses & Dissertations

With the rising prominence of electric vehicles (EVs) in the transportation sector, this thesis delves into the critical nexus between commercial EVs, charging infrastructure, and their consequential impacts on the power grid. As commercial EVs, particularly medium and heavy-duty variants, gain traction as viable alternatives in the commercial transportation landscape, understanding the intricacies of their charging requirements becomes paramount. This thesis critically examines the technological and logistical dimensions of the charging infrastructure for supporting commercial EVs, evaluating the consequential implications on the power grid and proposing strategies for mitigation through the utilization of Distributed Energy Resources (DERs). In tandem with …

Towards A Spaceworthy Cots Graphics Processing Unit: Hardware Performance Counter Based Symptomatic Fault Detection, Antonio E. Teijeiro

Open Access Theses & Dissertations

Ionizing radiation remains an obstacle to bringing graphics processing units (GPU) to space. Since radiation-hardened GPU chips are technically infeasible at the moment, an emphasis has been placed on the adaptation of commercial-off-the-shelf (COTS) GPUs to the space domain. At present, GPU error detection methods require redundant computation. This thesis work explores the utilization of hardware performance counters, special registers useful for monitoring internal GPU hardware events, for symptom-based, lightweight error detection. Hardware performance counters are successfully utilized for the detection of anomalous single event upsets in the L0 instruction cache, the load store unit, the arithmetic and logic unit, …

Gpu Based Monte Carlo Estimation Of Eddy Current Losses In Electromagnetic Coil-Core System, Adwaith Ravichandran

Theses and Dissertations

A novel parallelizable probabilistic approach to model eddy currents in AC electromagnets is presented in this research. Consequently, power loss associated with the formation of these eddy currents is estimated and validated using experimental data. Furthermore, predicting the effect of ferromagnetic alternating field enhancement on power loss in the source excitation winding has been an active area of research. Unlike a stationary field, an alternating sinusoidal field diffuses partially into the ferromagnetic material leading to a predictably sub-optimal field enhancement. To model these physics, finite element techniques employ nonlinear iterative solvers which are time consuming. A novel method is developed …

Cyber-Threat Detection Strategies Governed By An Observer And A Neural-Network For An Autonomous Electric Vehicle, Douglas Scruggs

All Theses

A pathway to prevalence for autonomous electrified transportation is reliant upon accurate and reliable information in the vehicle’s sensor data. This thesis provides insight as to the effective cyber-attack placements on an autonomous electric vehicle’s lateral stability control system (LSCS). Here, Data Integrity Attacks, Replay Attacks, and Denial-of-Service attacks are placed on the sensor data describing the vehicle’s actual yaw-rate and sideslip angle. In this study, there are three different forms of detection methods. These detection methods utilize a residual metric that incorporate sensor data, a state-space observer, and a Neural-Network. The vehicle at hand is a four-motor drive autonomous …

Project Thetis: A Low-Cost, Low-Profile Inertial Data Logger, Braidan Duffy

Theses and Dissertations

This thesis details the design, testing, calibration, and verification of a nine degree of freedom inertial measurement data logger for use with floating bodies. The instrument was conceived to address limitations of equipment used in classes within the Ocean Engineering department at Florida Institute of Technology. By meeting with several stakeholders and end users, a series of stakeholder requirements, capabilities, and component-level requirements were de- veloped that informed the design constraints. There were several hardware iterations of the board, culminating in Revision F5 which was extensively tested and proven. The design was inspected after testing concluded to determine which capabilities …

A Case Study In Cmos Design Scaling For Analog Applications: The Ringamp Ldo, Steven Corum

Masters Theses

As CMOS process nodes scale to smaller feature sizes, process optimizations are made to achieve improvements in digital circuit performance, such as increasing speed and memory, while decreasing power consumption. Unfortunately for analog design, these optimizations usually come at the expense of poorer transistor performance, such as reduced small signal output resistance and increased channel length modulation. The ring amplifier has been proposed as a digital solution to the analog scaling problem, by configuring digital inverters to function as analog amplifiers through deadzone biasing. As digital inverters naturally scale, the ring amplifier is a promising area of exploration for analog …

Investigating Mems Devices In Flow Conditions Relevant To Flow-Through Systems., Mohammad Shafquatul Islam

Electronic Theses and Dissertations

Advancements in microscale actuating technologies has substantially expanded the possibilities of interacting with the surrounding environment. Microstructures that deflect in response to mechanical forces are one of the largest application areas of microelectromechanical systems (MEMS). MEMS devices, functioning as sensors, actuators, and support structures, find applications in inertial sensors, pressure sensors, chemical sensors, and robotics, among others. Driven by the critical role of catalytic membrane reactors, this dissertation aims to evaluate enzyme activity on polymeric membranes and explore how fabrication methods from the field of Electrical and Computer Engineering (ECE) can incorporate sensing and actuation into these porous surfaces. Toward …

Hybrid Wall Outlet For Ac Or Dc Power Delivery, Garrett Knoller, Kerr Allan, Greg Perini

Electrical Engineering

The goal of this project is to develop hybrid DC and AC wall outlets for an efficient, flexible power interface. A DC plug standard is also proposed to allow DC devices to be safely powered by the outlet with the correct DC voltage for each device. The primary objective is to create a power outlet compatible with the proposed DC plug as well as NEMA 5-15 AC plugs, enabling the same outlet to power both types of load as needed. The outlet is intended for buildings and systems transitioning to an isolated DC grid to encourage DC development and adoption. …

Refinement And Performance Analysis Of The Stepped Frequency Microwave Radiometer In Extra Tropical Cyclone Conditions, Jezabel Vilardell Sanchez

Doctoral Dissertations

The Stepped Frequency Microwave Radiometer (SFMR) is a key instrument for estimation of ocean surface wind speed and rain rate in tropical and extra-tropical cyclones research. Through the observed brightness temperature (TB) over a range of six C-band frequencies, the SFMR derives these key parameters used by hurricane specialists to issue watches and warnings. The information gathered with this instru- ment is also pivotal for post-storm studies and satellite calibrations. Currently, the SFMR requires an average time of 5-10 seconds of averaging to cycle through the six di↵erent frequency channels, so in regions with strong wind/rain gradients such as the …

Analysis Of The Pros And Cons Of The Acquisition Of Training Ships By Metis, Jeremiah Yaw Frimpong

World Maritime University Dissertations

No abstract provided.

Design And Characterization Of 2.4ghz Antennas For Wireless Sensor Applications, Luis Zogby Brennan

Dissertations and Theses

Wireless sensor networks benefit greatly from advances in circuit integration and miniaturization. However, antennas are bound to specific geometries both in terms of fundamental limits and their response to immediate surroundings. As such, various successful techniques for antenna miniaturization must still be carefully tested and characterized as part of the design process of a sensor system. The work presented here fully characterizes a number of miniaturized 2.4GHz antennas and successfully integrates designs into a sensor system using the highly integrated Single Chip Micro Mote (SCµM), which uses a crystal-less radio design resulting in the requirement of only a …

Chip- And System-Level Reliability On Sic-Based Power Modules, Pengyu Lai

Graduate Theses and Dissertations

The blocking voltage, switching frequency and temperature tolerance of power devices have been greatly improved due to the revolution of wide bandgap (WBG) materials, such as silicon carbide (SiC) and gallium nitride (GaN). Owing to the development of SiC-based power devices, the power rating, operating voltage, and power density of power modules have been significantly improved. However, the reliability of SiC-based power modules has not been fully explored yet. Thus, this dissertation focuses on the chip- and system-level reliability on SiC-based power modules. For chip-level reliability, this work focuses on on-chip SiC ESD protection devices for SiC-based integrated circuits (ICs). …

Distributed Optimization With Limited Communication In Networks With Adversaries, Iyanuoluwa Emiola

Electronic Theses and Dissertations, 2020-

We all hope for the best but sometimes, one must plan for ways of dealing with the worst-case scenarios, especially in a network with adversaries. This dissertation illustrates a detailed description of distributed optimization algorithms over a network of agents, in which some agents are adversarial. The model considered is such that adversarial agents act to subvert the objective of the network. The algorithms presented in this dissertation are solved via gradient-based distributed optimization algorithm and the effects of the adversarial agents on the convergence of the algorithm to the optimal solution are characterized. The analyses presented establish conditions under …

Inkjet-Printed Electrochemical Sensors For Lead Detection, Annatoma Arif

Open Access Theses & Dissertations

This PhD dissertation research has developed a simple, miniaturized, sensitive, selective, reproducible, and disposable 3D (inkjet printed – additive manufacturing technology) gold (Au) plated electrochemical sensor (ECS) on shape memory polymer (SMP) for aqueous lead detection. This technology has shown promising performance in the application of electrochemical sensing (lead (II) detection) due to increased effective electrode surface area (7.25 mm^2 ± 0.15 mm^2) despite miniaturizing lateral surface area (4.19 mm^2). The design, fabrication processes, optimization including bismuth functionalization, evaluation, uncertainty analysis, and cost analysis of the novel SMP based inkjet printed Au plated sensor have been delineated in this manuscript …

Metal Additive Microfabrication Of Semiconductor Packages With Inbuilt Thermal Management System, Bhushan Lohani

Open Access Theses & Dissertations

Moore’s law describes the development capabilities in electronics manufacturing. Although his estimation held for decades, at present, the doubling of components every two years seems to be approaching a halt. The assessment was based on the miniaturization of transistors to create space for more. Miniaturization led to higher component density, decreased cost, lowered power consumption, and compactness. However, it also came with high current density, increased Joule heating, and reduced critical charge. One of the limiting factors is the heat generated from such devices, which is heavily discussed in International Roadmap for Devices and Systems (IRDS) and International Technology Roadmap …

Characterization, Simulation, And Test Method For Image Artifacts Due To Phase Drift Of The Saw Filter In The Magnetic Resonance Receiver, Gabriel T. Jacobs

Theses and Dissertations

The receiver for a Magnetic Resonance (MR) scanner is responsible for capturing the precise frequency and phase of extremely low-power RF signals emanating from the human body; and consequentially must minimize unexpected phase drift in the received signal. One well-known source for temperature-dependent phase drift in RF electronics is the Surface Acoustic Wave (SAW) filter. In this work, the phase drift due to temperature changes in the SAW filter of an MR receiver was evaluated for its potential effects on image quality using several image quality metrics. A lab bench method was developed to playback MR images using typical lab-equipment …

Ultra Fast Dc Switch, Ian A. Buck

Theses and Dissertations

With advancements in power electronics, DC power systems are a strong contender forfuture power system and shipboard application studies. However, to ensure proper DC power systems, protection engineers must develop different DC protection schemes to maintain proper system protection levels. The critical issue behind developing DC protection devices is that the signal never crosses zero naturally, as in AC circuit breakers and AC disconnect switches. There is also a necessity for galvanic isolation in the DC protection system. A method developed is pairing a mechanical commercial-off-the-shelf vacuum interrupter, a Thomson coil actuator, and a current commutating drive circuit (CCDC). The …

Investigation Of Vo2 Thin Films And Devices For Opto-Electromechanical Applications, Samee Azad

All Dissertations

Specialized and optimized low pressure direct oxidation technique have been implemented to synthesize high quality VO₂ thin films on various substrates (sapphire, SiO₂/Si, AT-cut quartz, GaN/AlGaN/GaN/Si and muscovite). Structural and surface characterization methods such as X-ray diffraction, Raman spectroscopy and atomic force microscopy have been administered on the grown VO₂ films which indicate their material quality. Transition of characteristics of the VO₂ films are caused by semiconductor metal transition (SMT). This phenomenon is attributed as the change maker in transition of resistivity and transmitted optical power through the VO₂ films. Apart the substrates mentioned, …

The Application Of Model Predictive Control On Paralleled Converters For Zero Sequence Current Suppression And Active Thermal Management, Justin Dobey

All Theses

In the field of power electronics, the control of rectifiers is a crucial area of study. Rectifiers are used to convert AC power into DC power, and are commonly used in a wide range of applications, including renewable energy systems, industrial automation, and consumer electronics. However, in medium and high-power systems when multiple rectifiers are connected in parallel to a DC bus, stability issues can arise, including voltage fluctuations, zero sequence circulating current, and thermal imbalance.

Achieving stable DC bus voltage is essential for maintaining the proper functioning of electronic devices, while suppressing zero sequence current is necessary for protecting …