Engineering Commons^™

Static And Dynamic State Estimation Applications In Power Systems Protection And Control Engineering, Ibukunoluwa Olayemi Korede

Doctoral Dissertations

The developed methodologies are proposed to serve as support for control centers and fault analysis engineers. These approaches provide a dependable and effective means of pinpointing and resolving faults, which ultimately enhances power grid reliability. The algorithm uses the Least Absolute Value (LAV) method to estimate the augmented states of the PCB, enabling supervisory monitoring of the system. In addition, the application of statistical analysis based on projection statistics of the system Jacobian as a virtual sensor to detect faults on transmission lines. This approach is particularly valuable for detecting anomalies in transmission line data, such as bad data or …

Fourier Analysis And Optimization Of Inductive Wireless Power Transfer For Electric Vehicle Charging, Andrew P. Foote

Doctoral Dissertations

With the growth of electric vehicle (EV) popularity, different charging options to increase user convenience and reduce charging time such as high power wireless charging are increasingly being developed and researched. Inductive wireless power transfer (WPT) systems for EVs must meet specifications such as stray field, battery power and voltage operating range, efficiency, and ground clearance. The coil geometry and design have a large impact in meeting these constraints. Typical design approaches include iterative analysis of predetermined coil geometries to identify candidates that meet these constraints.

This work instead directly generates WPT coil shapes and magnetic fields to meet specifications …

A Case Study In Cmos Design Scaling For Analog Applications: The Ringamp Ldo, Steven Corum

Masters Theses

As CMOS process nodes scale to smaller feature sizes, process optimizations are made to achieve improvements in digital circuit performance, such as increasing speed and memory, while decreasing power consumption. Unfortunately for analog design, these optimizations usually come at the expense of poorer transistor performance, such as reduced small signal output resistance and increased channel length modulation. The ring amplifier has been proposed as a digital solution to the analog scaling problem, by configuring digital inverters to function as analog amplifiers through deadzone biasing. As digital inverters naturally scale, the ring amplifier is a promising area of exploration for analog …

Development Of A Soft Robotic Approach For An Intra-Abdominal Wireless Laparoscopic Camera, Hui Liu

Doctoral Dissertations

In Single-Incision Laparoscopic Surgery (SILS), the Magnetic Anchoring and Guidance System (MAGS) arises as a promising technique to provide larger workspaces and field of vision for the laparoscopes, relief space for other instruments, and require fewer incisions. Inspired by MAGS, many concept designs related to fully insertable magnetically driven laparoscopes are developed and tested on the transabdominal operation. However, ignoring the tissue interaction and insertion procedure, most of the designs adopt rigid structures, which not only damage the patients' tissue with excess stress concentration and sliding motion but also require complicated operation for the insertion. Meanwhile, lacking state tracking of …

Reducing The Levelized Cost Of Energy Of Residential Pv Inverters Through Dynamic Hardware Allocation, Kamal Sabi

Doctoral Dissertations

Renewable energy, such as wind and solar are becoming an integral part of world energy production. Photovoltaic (PV) systems are projected to constitute a large portion of the energy generation portfolio. Achieving a low-cost residential PV system will enable the wide adoption of solar energy throughout the USA. Although innovation in several areas is required to achieve this goal of a low-cost residential PV system, inverter reliability innovation is one key area that is essential. Present string inverters' lifetime is less than 15 years. Increasing their lifetime to 50 years will reduce the cost of operation and maintenance, increase energy …

Multiple Objective Co-Optimization Of Switched Reluctance Machine Design And Control, Timothy Burress

Doctoral Dissertations

This dissertation includes a review of various motor types, a motivation for selecting the switched reluctance motor (SRM) as a focus of this work, a review of SRM design and control optimization methods in literature, a proposed co-optimization approach, and empirical evaluations to validate the models and proposed co-optimization methods.

The switched reluctance motor (SRM) was chosen as a focus of research based on its low cost, easy manufacturability, moderate performance and efficiency, and its potential for improvement through advanced design and control optimization. After a review of SRM design and control optimization methods in the literature, it was found …

A Low Power, Rad-Hard, Ecl Standard Cell Library, Zakaraya A. Hamdan

Masters Theses

Space exploration for life both inside and outside of our solar system demand the design and fabrication of robust, reliable electronics that can take measurements, process data, and sustain necessary operations. However, the presence of high radiation and the cold temperature of space poses a challenge to most designers. This thesis presents the design of a radiation-hardened, cold capable emitter coupled logic standard cell library with the intention of being used for space applications. The cells are designed and fabricated in a 90nm silicon germanium BiCMOS process. First, a review of emitter coupled logic is presented. Then, the design methodology …

Analysis And Development Of Multiple Phase Shift Modulation In A Sic-Based Dual Active Bridge Converter, Yu Yan

Doctoral Dissertations

Renewable energy adoption is a popular topic to release the stress of climate change caused by greenhouse gas. Electricity is ideal secondary energy for clean primary energy such as nuclear, wind, photovoltaic, and so on. To extend the application of electricity and reduce fossil energy consumption by transportation sectors, electric vehicles (EVs) become promising technology that can further inspire the development of renewable energy.

Battery as the core in an EV provides the energy to the motor and all on-board electric equipment. The battery charger is mainly composed of a power factor correction (PFC) and isolated DC-DC converter. Therefore, power …

Power Quality Control And Common-Mode Noise Mitigation For Inverters In Electric Vehicles, Yang Huang

Doctoral Dissertations

Inverters are widely utilized in electric vehicle (EV) applications as a major voltage/current source for onboard battery chargers (OBC) and motor drive systems. The inverter performance is critical to the efficiency of EV system energy conversion and electronics system electro-magnetic interference (EMI) design. However, for AC systems, the bandwidth requirement is usually low compared with DC systems, and the control impact on the inverter differential-mode (DM) and common-mode (CM) performance are not well investigated. With the wide-band gap (WBG) device era, the switching capability of power electronics devices drastically improved. The DM/CM impact that was brought by the WBG device-based …

Stability Analysis And Design Of Grid-Interactive Power Electronic Converters, Le Kong

Doctoral Dissertations

The increasing penetration of power electronic converters (PECs) can provide high flexibility, full controllability, sustainability, and improved efficiency for future electric power systems. However, it also introduces new challenges since the wide-frequency-band control dynamics of PECs can interact with the power system and result in different types of instability issues. To holistically address the instability issues, several research activities are conducted in this dissertation.

The modular multilevel converter (MMC), which is one of the most common PECs in high- or medium-voltage power systems, is investigated. An improved MMC dc impedance model is developed by considering both the submodule voltage and …

Load Modeling And Evaluation Of Leds For Hardware Test Bed Application, Jillian M. Ruff

Masters Theses

The lighting industry was revolutionized with the emergence of LED lighting. Over the last 15 years, LED lighting device sales and utilization have grown immensely. The growth and popularity of LEDs is due to improved operation of the device when compared to previous lighting technologies. Efficient performance of the device is critical due to the growth of global energy consumption.

As nonrenewable generation fuel is finite, utilities have begun the transition to renewable energy generation. Generation and distribution systems become inherently complex to comprehend and maintain with incorporation of emerging supply and load technologies. With the unprecedented growth of LED …

A Bulk Driven Transimpedance Cmos Amplifier For Sipm Based Detection, Shahram Hatefi Hesari

Masters Theses

The contribution of this work lies in the development of a bulk driven operational
transconducctance amplifier which can be integrated with other analog circuits and
photodetectors in the same chip for compactness, miniaturization and reducing the
power. Silicon photomultipliers, also known as SiPMs, when coupled with scintillator materials are used in many imaging applications including nuclear detection. This thesis discuss the design of a bulk-driven transimpedance amplifier suitable for detectors where the front end is a SiPM. The amplifier was design and fabricated in a standard standard CMOS process and is suitable for integration with CMOS based SiPMs and commercially …

Systematic Design Of A 100 W 6.78 Mhz Wireless Charging Station Covering Multiple Devices And A Large Charging Area, Jie Li

Doctoral Dissertations

Wireless power transfer (WPT) promises to offer safe and convenient charging in consumer electronics applications. The application ranges from sub-watt medical implant device charging to watt-level household charging, further to the kilowatt electric vehicle (EV) and railway charging. At present, two industry standards are widely used to guide the WPT product design. The Qi standard describes an application that requires the receiver to be placed close to the transmitter, called "tightly coupled" WPT. The receiver coil typically has a similar size compared to the transmitter. And the operation frequency is in the kHz range. The Airfuel standard, on the other …

A Ringamp-Assisted, Output Capacitor-Less Analog Cmos Low-Dropout Voltage Regulator, Jordan Sangid

Doctoral Dissertations

Continued advancements in state-of-the-art integrated circuits have furthered trends toward higher computational performance and increased functionality within smaller circuit area footprints, all while improving power efficiencies to meet the demands of mobile and battery-powered applications. A significant portion of these advancements have been enabled by continued scaling of CMOS technology into smaller process node sizes, facilitating faster digital systems and power optimized computation. However, this scaling has degraded classic analog amplifying circuit structures with reduced voltage headroom and lower device output resistance; and thus, lower available intrinsic gain. This work investigates these trends and their impact for fine-grain Low-Dropout (LDO) …

Data Center Power System Emulation And Gan-Based High-Efficiency Rectifier With Reactive Power Regulation, Jingjing Sun

Doctoral Dissertations

Data centers are indispensable for today's computing and networking society, which has a considerable power consumption and significant impact on power system. Meanwhile, the average energy usage efficiency of data centers is still not high, leading to significant power loss and system cost.

In this dissertation, effective methods are proposed to investigate the data center load characteristics, improve data center power usage efficiency, and reduce the system cost.

First, a dynamic power model of a typical data center ac power system is proposed, which is complete and able to predict the data center's dynamic performance. Also, a converter-based data center …

A High Frequency Wireless Power Transfer System For Electric Vehicle Charging Using Multi-Layer Non-Uniform Self-Resonant Coil, Ruiyang Qin

Doctoral Dissertations

Wireless EV (Electric Vehicle) charging is an emerging technology with rapid development in the past decade. Compared to wired EV chargers, wireless power transfer (WPT) enables safe and unobtrusive charging for EVs.

This work proposes high frequency wireless charging using a self-resonant (SR) coil at several megahertz. A multi-layer self-resonant coil structure is proposed, allowing high quality factor coils to be fabricated from layers of inexpensive copper foil and dielectric film. Additionally, the self-resonant coil utilizes its interlayer capacitance for resonance, eliminating the external compensation capacitor and shrinking the overall volume of passive component to increase the power density. Comparing …

Development Of Arduino-Based Portable Systems For Electroanalytical Detection, Jiamei Huang

Masters Theses

This work presents the development of a multi-mode electroanalytical detection system based on Arduino microcontroller board. First, a multichannel impedance readout system is designed for alternating current electrokinetics (ACEK) based capacitive sensing. ACEK phenomena on 100μm interdigitated electrodes are observed via fluorescent particles as well as bioparticles, which illustrate the mechanisms of ACEK target enrichment for the capacitive sensing method. I2C multiplexer is applied to allow multiple impedance converters to work together providing continuous AC signals for ACEK capacitive sensing. Second, an electronic nose composed of three modules including a gas sensor array, a circuit for signal acquisition integrated with …

The Bracelet: An American Sign Language (Asl) Interpreting Wearable Device, Samuel Aba, Ahmadre Darrisaw, Pei Lin, Thomas Leonard

Chancellor’s Honors Program Projects

No abstract provided.

Design And Evaluation Of A Unique Weighted-Sum-Based Anger Camera, Matthew W. Seals

Masters Theses

Anger camera imaging technology has become widely popular for neutron diffraction imaging due to recent shortages in Helium-3 (He-3). Research into neutron diffraction optimized Anger camera by the Oak Ridge National Laboratory (ORNL) detectors group has provided an alternative to He-3 Tube-based detectors with a high-resolution Anger camera. However, the cost of these high-resolution Anger camera technology can make it less attractive than He-3 tubes when a large Field of View (FOV) is desired. Currently, there is a need for a lower-cost alternative to this high-resolution anger camera. Further applications for Anger camera have become of interest with the advent …

Modeling And Control Of A 7-Level Switched Capacitor Rectifier For Wireless Power Transfer Systems, Spencer Cochran

Doctoral Dissertations

Wireless power continues to increase in popularity for consumer device charging. Rectifier characteristics like efficiency, compactness, impedance tunability, and harmonic content make the multi-level switched capacitor rectifier (MSC) an exceptional candidate for modern WPT systems. The MSC shares the voltage conversion characteristics of a post-rectification buck-boost topology, reduces waveform distortion via its multi-level modulation scheme, demonstrates tank tunability via the phase control inherent to actively switched rectifiers, and accomplishes all this without a bulky filter inductor. In this work, the MSC WPT system operation is explained, and a loss model is constructed. A prototype system is used to validate the …

Partial Discharge Testing And Detection Under Pwm Voltage, John Meadors

Masters Theses

Partial Discharge detection and measurement is an important part of electric insulation design. However, in PWM (pulse width modulation) voltage source converter environments, the noise resulting from switching voltage (rise and fall times of tens of nanoseconds) makes detection and extraction of partial discharge difficult. Unique methods of partial discharge detection are needed to address and decouple the noise from partial discharge measurements. PWM voltage can feature high switching speeds and high dv/dt during voltage switching. These PWM voltage behaviors are not found in traditional utility high voltage applications, and the effects that this type of voltage has on insulation …

Modeling, Measurement And Mitigation Of Fast Switching Issues In Voltage Source Inverters, Wen Zhang

Doctoral Dissertations

Wide-bandgap devices are enjoying wider adoption across the power electronics industry for their superior properties and the resulting opportunities for higher efficiency and power density. However, various issues arise due to the faster switching speed, including switching transient voltage overshoot, unstable oscillation, gate driving and evaluation difficulty, measurement and monitoring challenge, and potential load insulation degradation. This dissertation first sets out to model and understand the switching transient voltage overshoots. Unique oscillation patterns and features of the turn-on and turn-off overvoltage are discovered and analyzed, which provides new insights into the switching transient. During the experimental characterization, a new unstable …

Impact And Application Of Real-Time Control On Stormwater Systems, Aaron A. Akin

Doctoral Dissertations

Stormwater control measures (SCMs) such as dry extended detention basins and wet ponds are common practices implemented by engineers and designers to mitigate the impact of stormwater runoff. These practices are designed based on historical rainfall data to attenuate runoff to pre-development conditions and, once they are installed, are unable to adapt to changing rainfall patterns or watershed restoration objectives. To solve these climate resiliency issues, several studies were conducted which investigated the impact of retrofitting such systems with a controllable outlet to increase or change detention times during rainfall events along with the novel instrumentation and methodologies necessary for …

Development Of An Encrypted Wireless System For Body Sensor Network Applications, Kendra Anderson

Masters Theses

Wireless body area networks (WBAN), also called wireless body sensor networks (WBSN), consist of a collection of wireless sensor nodes used to monitor and assess various human physiological conditions, which can then be used by healthcare professionals to help them make important healthcare decisions. They can be used to prevent disease, help diagnosis a disease, or manage the symptoms of a disease. An extremely important aspect of WBAN is security to protect a patient's healthcare information, as a hacker could potentially cause fatal harm. Current security measures are implemented in software at the MAC layer and higher, not in the …

Development Of A Point-Of-Use Testing Platform For Detecting Bacteria Infection In Raw Milk, Xin Xia

Masters Theses

The detection and quantification of bacteria are essential to environment and food quality monitoring. Escherichia coli (E. coli) is a common pathogen, also a causative agent of mastitis. Traditional methods usually require samples to be tested in a laboratory. However, sending samples to remote lab increases the cost of time and money spent on delivery. Sometimes, samples can degrade during this long progress and cause inaccuracy. A low cost and reusable sensor is designed to perform on-site quantification. The sensor composed of two layers of asymmetrical mesh electrodes, which is used in coordination magnetic microparticles functionalized with bacterium-specific antibody. Immunological …

Development Of A Converter-Based Testing Platform And Battery Energy Storage System (Bess) Emulator For Microgrid Controller Function Evaluation, Dingrui Li

Masters Theses

The microgrid has attracted increasing research attention in the last two decades. Due to the development of renewable energy resources and power electronics technologies, the future microgrid will trend to be smarter and more complicated. The microgrid controller performs a critical role in the microgrid operation, which will also become more and more sophisticated to support the future microgrid. Before final field deployment and test, the evaluation and testing of the controller is an indispensable step in the controller development, which requires a proper testing platform.

However, existing simulation-based platforms have issues with potential numerical oscillation and may require huge …

Design And Implementation Of An Isfet Sensor With Integration Of An On-Chip Processor, Shaghayegh Aslanzadeh

Doctoral Dissertations

Portable sensors are used in many applications. Among them, pH sensors are suitable for quantifying and identifying various analytes in real-time and doing so non-invasively. The analytes may have environmental impact such as in water quality monitoring. The analytes may also have biological impact such as monitoring cell culture or remote patient health assessment. CMOS based sensors are compact and enable low power consumption suitable for these portable applications.

This work reports on the development of a portable CMOS based pH sensor. The contributions of this dissertation are as follows. First, a differential pH sensor, with two different sized electrodes …

Design Of Power Receiving Units For 6.78mhz Wireless Power Transfer Systems, Hoang Phuc Tran Pham

Masters Theses

In the last decade, the wireless power transfer (WPT) technology has been a popular topic in power electronics research and increasingly adopted by consumers. The AirFuel WPT standard utilizes resonant coils to transfer energy at 6.78 MHz, introducing many benefits such as longer charging distance, multi-device charging, and high tolerance of the coil misalignment. However, variations in coil coupling due to the change in receiving coil positions alter the equivalent load reactance, degrading efficiency.

In recent studies, active full-bridge rectifiers are employed on WPT receivers because of their superior efficiency, controllability, and ability to compensate for detuned WPT networks. In …

Design And Implementation Of A Multi-Modal Sensor With On-Chip Security, Ava Hedayatipour

Doctoral Dissertations

With the advancement of technology, wearable devices for fitness tracking, patient monitoring, diagnosis, and disease prevention are finding ways to be woven into modern world reality. CMOS sensors are known to be compact, with low power consumption, making them an inseparable part of wireless medical applications and Internet of Things (IoT). Digital/semi-digital output, by the translation of transmitting data into the frequency domain, takes advantages of both the analog and digital world. However, one of the most critical measures of communication, security, is ignored and not considered for fabrication of an integrated chip. With the advancement of Moore's law and …

Modeling And Optimization Algorithm For Sic-Based Three-Phase Motor Drive System, Ren Ren

Doctoral Dissertations

More electric aircraft (MEA) and electrified aircraft propulsion (EAP) becomes the important topics in the area of transportation electrifications, expecting remarkable environmental and economic benefits. However, they bring the urgent challenges for the power electronics design since the new power architecture in the electrified aircraft requires many benchmark designs and comparisons. Also, a large number of power electronics converter designs with different specifications and system-level configurations need to be conducted in MEA and EAP, which demands huge design efforts and costs. Moreover, the long debugging and testing process increases the time to market because of gaps between the paper design …