Engineering Commons^™

Hybrid Wall Outlet For Ac Or Dc Power Delivery, Garrett Knoller, Kerr Allan, Greg Perini

Electrical Engineering

The goal of this project is to develop hybrid DC and AC wall outlets for an efficient, flexible power interface. A DC plug standard is also proposed to allow DC devices to be safely powered by the outlet with the correct DC voltage for each device. The primary objective is to create a power outlet compatible with the proposed DC plug as well as NEMA 5-15 AC plugs, enabling the same outlet to power both types of load as needed. The outlet is intended for buildings and systems transitioning to an isolated DC grid to encourage DC development and adoption. …

Designing The Power System Of A Robot, Nolan Hays

Honors College Theses

This thesis outlines the acquired skills and knowledge acquired through the course of four years of Murray State University’s School of Engineering. The capstone for students in the department was to team up and complete an interdisciplinary senior design project using skills from various tracks of engineering. For this thesis, there is a greater emphasis on the electrical engineering track. The objective of the project was to build an autonomous robot to complete the various tasks within the scope of the IEEE SoutheastCon 2023 Hardware Competition. The robot was controlled via a Raspberry Pi 4 Model B. There were three …

A Review Of Piezoelectric Footwear Energy Harvesters: Principles, Methods, And Applications, Bingqi Zhao, Feng Qian, Alexander Hatfield, Lei Zuo, Tian-Bing Xu

Mechanical & Aerospace Engineering Faculty Publications

Over the last couple of decades, numerous piezoelectric footwear energy harvesters (PFEHs) have been reported in the literature. This paper reviews the principles, methods, and applications of PFEH technologies. First, the popular piezoelectric materials used and their properties for PEEHs are summarized. Then, the force interaction with the ground and dynamic energy distribution on the footprint as well as accelerations are analyzed and summarized to provide the baseline, constraints, potential, and limitations for PFEH design. Furthermore, the energy flow from human walking to the usable energy by the PFEHs and the methods to improve the energy conversion efficiency are presented. …

Developing Positive Thermal Coefficient (Ptc) Heaters For Solar Electric Cooking, Katarina Ivana Brekalo, Andrew Shepherd

Physics

Positive Thermal Coefficients, PTCs, are materials that abruptly change in resistance in response to changes in temperature. The purpose of this experiment is to explore the viability of using the switching type ceramic PTC thermistor as a replacement for current resistive heaters. These types of PTCs have a nonlinear change in resistance with increases in temperature. This device will be used as a temperature-controlling heating element intended to power an Insulated Solar Electric Cooker (ISEC). The ISEC is designed to cook meals throughout the day for impacted communities as an alternative cooking method that doesn’t require biofuel as an energy …

Installation Of Electrical System For Paso Robles Police Department, Peter D. Strykers, Jacob M. Studebaker

Construction Management

This paper outlines the process that Peter Strykers and Jacob Studebaker went through to set up the lighting and power system for the Paso Robles Police Department gun range located off highway 46. Before our installation, the gun range had zero lighting so the officers could not use it after sunset. We allowed the officers to light the gun range with outdoor LED lights, light up both the storage units on site, and have access to multiple outlets inside and out of the storage units. The power source that the electrical system runs on comes from a Kubota generator because …

Development Of A Reference Design For A Cyber-Physical System, Nicholas Paul Blair

Graduate Theses and Dissertations

The purpose of this thesis is to develop a reference design to assist in the selection of security practices in power electronics design. A prototype will be developed from this reference design for evaluation. This evaluation will include a brief cost/benefit analysis to gauge the efficacy of implementing each layer of security throughout the power electronics design process. This thesis will also describe the obstacles and effectiveness of integrating a Trusted Platform Module (TPM) into a cyber-hardened grid-connected device. The TPM device is a secured crypto processor that assists in generating, storing, and restricting the use of cryptographic keys. The …

Lawn Buddy, Jayson Johnston, Andrew Brown, Jacob Maljian

Electrical Engineering

Grass lawns are a common hallmark of the American home. In 2019, a survey from the National Association of Landscape Professionals found that 81% of all Americans owned a lawn [1]. Mowing is a time consuming and costly chore that is part of maintaining a grass lawn. The manual labor in mowing a lawn can exceed 40 hours per year [2]. People commonly incur weekly costs on mowing services to save time. Traditional gas powered mowers are physically demanding and use engines that need routine maintenance. They operate loudly enough that users should be wearing hearing protection and the noise …

Dc To Dc Usb-C Charger, Nikki Gmerek, Kenneth Nguyen, Uriel Serna

Electrical Engineering

The DC House USB-C Charger will convert the 48V input from the DC house, found on the Cal Poly campus, to 3 USB-C outputs: 5V, 12V, and 24 volts. The converter will deliver a total of 185 Watts out across all 3 outputs, with an efficiency greater than 82% at full load. The USB-C ports will be used to connect to compatible phones, laptops or any other device for charging/powering purposes. The goal of this project is to develop the most efficient and safe converter to deliver power to multiple outputs using USB-C, for items as small as a cell …

The Modified-Multiphase Boost Converter: Combined Inductors And Capacitors Topology, Zachary L. Eldredge

Master's Theses

In this work, a modified boost converter design has been implemented in a multiphase configuration with a condensed topology. The modified aspect of the design has already been proven to drastically reduce input current ripple by about 40% in a single-phase implementation. By placing two modified boost converters in parallel with interleaving main switches (multiphase), the input inductors and modified capacitors of the modified topology can be reduced to just one of each, lowering the number of components, size, and cost. Additionally, multiphase DC/DC converters lower input/output voltage and current ripples while delivering more power compared to single-phase converters. By …

Contributions To Hybrid Power Systems Incorporating Renewables For Desalination Systems, Nasser Alawhali

Theses and Dissertations--Electrical and Computer Engineering

Renewable energy is one of the most reliable resource that can be used to generate the electricity. It is expected to be the most highly used resource for electricity generation in many countries in the world in the next few decades. Renewable energy resources can be used in several purposes. It can be used for electricity generation, water desalination and mining. Using renewable resources to desalinate the water has several advantages such as reduce the emission, save money and improve the public health. The research described in the thesis focuses on the analysis of using the renewable resources such as …

Dc-To-Dc Buck Converter, Kyle Christopher Roman

Electrical Engineering

The growth of sustainable energy requires many components to work in harmony creating one efficient and effective system. Sustainable energy generation that produces a DC current varying in voltage requires a subsystem to convert voltage to a practical and usable value. The DC to DC Buck converter converts high DC solar generated voltage to a 12V output. This Modular -Level power electronic (MLPE) device performs as a solar charge controller for small lithium ion batteries. Fluctuating voltage levels generated by Photovoltaic cells makes the solar controller a critical part of the solar system. Regulating the DC voltage allows safe and …

Hybrid Water Pump, Dylan W. Grant, Wei Chen Yeh

Electrical Engineering

This project seeks to use multiple sources to power a water pump. We will design a system which will combine inputs from solar and wind energy production to ensure the pump will have enough power to run. This will create a system powered by clean energy and will be self-sustained once completed. This will theoretically create a more sustainable source of power for the pump than only one of the sources. Because the power sources don’t require outside inputs (aside from sun and wind), the pump can be placed in a remote area. This could be very helpful in developing …

Dc House Energy Management System, Zachary L. Eldredge, Zoe M. Hay

Electrical Engineering

In this work, a previously completed proof of concept for an Energy Management System (EMS) for the DC House project has been revised and re-implemented. The implemented design changes will improve the performance and reproducibility of the system. This new design of the EMS replaces the two-separate buck and boost DC-DC converters with a single bidirectional DC-DC converter to reduce components and improve efficiency. Analysis of the bidirectional DC-DC converter shows high efficiency especially at larger load currents. The code of the previous work was updated for smoother operation as well as to accommodate an LCD capable of displaying more …

Ac Power Monitoring System, Jared L. Newman, Luke M. Tomlinson, Grayson H. Dearing, Frederick G. Harmon

Channels: Where Disciplines Meet

Motivated by high energy costs, people and organizations want to cut back on their energy consumption. However, the only feedback consumers typically receive is a monthly bill listing their total electricity usage (in kWh). Some companies have begun developing systems that allow households and organizations to monitor their energy usage for individual circuits. Available systems are expensive so a CU engineering senior design team has designed, fabricated, and tested a system for use at Cedarville University. The AC power monitoring system has the ability to measure energy consumption for each individual circuit in the breaker panel, store the data, and …

Testing Feasibility Of Inductive Power Coupling For Modern Applications, Andrew Burman

BioResource and Agricultural Engineering

This project takes two bifilar tesla coils and uses them to find a % efficiency of power transfer as distances between the coils decrease. The reason this experiment is being conducted is to find possible implications for wireless charging of vehicles using similar style coils. This project conducted experiments on 60 Hz, 400 Hz, and 1 kHz frequencies for a small input signal. The general conclusion is that as the frequency increases more power can be transferred and higher efficiency of power transfer is seen. This project also concluded that it could be possible to get higher efficiency at a …

Applications Of Impedance Identification To Electric Ship System Control And Power Hardware-In-The-Loop Simulation, Jonathan Siegers

Theses and Dissertations

Recent advances in semiconductor technology, controls, and switching converter topologies have resulted in the increasing application of power electronics in power distribution systems. Power electronic enabled distribution systems have inspired a renewed interest in DC distribution architectures as an appealing alternative to traditional AC methods due to the significant performance and efficiency gains they offer. However, the notional power electronic based DC distribution system is a complex and extensively interconnected system consisting of multiple power converters. As a result, a number of system-level challenges related to stability arise due to interaction among multiple power converters. In addition, the power distribution …

Dual-Input Dc-To-Dc Converter Topologies And Control Schemes, Shaun Alan Stickel

Boise State University Theses and Dissertations

Dual-input DC-to-DC converters are power supplies that draw power from two sources simultaneously and deliver power to a single load, the ratio of power drawn from each source and be held constant with changes in the load. Applications for dual-input power supplies are computer systems, mobile systems using energy harvesting, and systems needing redundant power supplies. This writing covers the operation and control of dual-input DC-to-DC converters that implement a non-inverting buck-boost function and utilize only a single power path.

Traditionally, a dual-input power supply is created by placing two standard power paths in parallel. This adds considerable control complexity …

Enterprise Smart Outlet, David Faltmier, Matthew Mcgill, Luke Stencel

Electrical Engineering

The purpose of our senior project, Enterprise Smart Outlet, is to create an electrical outlet which will allow enterprise users to monitor and change their power consumption habits on a large scale. The initial goal of this project is to allow consumers to see their power consumption per outlet in real time, and then using that information conform their future habits to help them conserve electrical energy, and more importantly, money. Three requirements for our project to meet our initial goal are, the outlet will work in a standard electrical outlet and be completely compatible with current electrical standards, the …

Design And Fabrication Techniques Of Devices For Embedded Power Active Contact Lens, Errol Heradio Leon

Master's Theses

This thesis designed and fabricated various devices that were interfaced to an IC for an active contact lens that notifies the user of an event by detection of an external wireless signal. The contact lens consisted of an embedded antenna providing communication with a 2.4GHz system, as well as inductive charging at an operating frequency of 13.56 MHz. The lens utilized a CBC005 5µAh thin film battery by Cymbet and a manufactured graphene super capacitor as a power source. The custom integrated circuit (IC) was designed using the On Semiconductor CMOS C5 0.6 µm process to manage …

Cal Poly Wind Power Research Center Power Regulator, Ricardo Rodriguez, Steven Bounchareune

Electrical Engineering

Through funding from the California Central Coast Research Partnership (C3RP) the

CPWRC, led by Dr. Patrick Lemieux, has erected a horizontal axis wind turbine (HAWT) at the

Cal Poly Escuela Ranch site EL04. With the help of Dr. John Ridgely and Dr. Art MacCarley, the team has implemented a controller that delivers the power being generated by the turbine to a resistor bank which maintains a safe working speed for the turbine. The authors objectives for this project are to (1) become familiar with the operation of the turbine, (2) develop an AC-DC converter that regulates the output of the …

Efficient, Scalable, Parallel, Matrix-Matrix Multiplication, Enrique Portillo

Open Access Theses & Dissertations

For the past decade, power/energy consumption has become a limiting factor for large-scale and embedded High Performance Computing (HPC) systems. This is especially true for systems that include accelerators, e.g., high-end computing devices, such as Graphics Processing Units (GPUs), with terascale computing capabilities and high power draws that greatly surpass that of multi-core CPUs. Accordingly, improving the node-level power/energy efficiency of an application can have a direct and positive impact on both classes of HPC systems.

The research reported in this thesis explores the use of software techniques to enhance the execution-time and power-consumption performance of applications executed on a …

Analysis Of Modulation And Voltage Balancing Strategies For Modular Multilevel Converters, Ryan Blackmon

Theses and Dissertations

Modular multilevel converters are an emerging voltage source converter topology suitable for many applications. The increased utilization of HVDC power transmission solutions has resulted in modular multilevel converters becoming a more common converter type. Other applications include interfacing renewable energy power sources to the grid and motor drives. Modular multilevel converters are beneficial for medium voltage motor drives because the properties of this converter topology, such as low distortion, allow for an efficient motor drive design.

Modular multilevel converters are designed where instead of using 6 IGBTs as in a conventional voltage source converter, numerous low-rated IGBTs are used to …

Application Of Wireless Power For Charging The Battery Of A Wireless Mouse, Jacob Keast, Vincent Jison

Electrical Engineering

Electronic devices are a part of all modern homes, but restricted by available outlets and the hassle of wires. With the modern wireless mouse, this is also the case. When the battery is low the consumer has several options: it is replaced with a new battery, it can be recharged using a USB wire, or the mouse is placed on a charging dock. This project provides an alternative to these options and allows the mouse’s battery to be charged via wireless inductive coupling. The wireless power charging system that was implemented in this project was successful in its ability to …

Portable Solar Powered Charging Station, Jordan Bonner

Electrical Engineering

The portable solar powered charging station uses a solar powered mat that can be folded for portability. The device has the ability to charge small electronics during both day and night. When sunlight is available, the charger charges two C batteries in series and at the same time it charges any electronic device that can be connected via USB or cigarette lighter. At night the charger will charge the same electronic devices from the onboard batteries. The charging station must be able to interface with electronic devices using USB and a car cigarette lighter to charge the device’s battery.

Hydro-Electric Generation System For The Dc House Project, Dennis Kwan, Mitchell Krug

Electrical Engineering

This paper focuses on the design, integration, and construction of a system that harnesses energy from flowing water. The system will be used in conjunction with the DC House Project. The proposed system employs a DC generator and DC-DC Boost-converter to provide electricity to the DC House at approximately 200-300W. Results of the testing and measurement show that the goal of the system is feasible, but currently limited. The generator could not output the specified power. Details of the design, along with ideas for further improvement, are presented in this report.

Validated Real-Time Energy Models For Small-Scale Grid-Connected Pv-Systems, Lacour Ayompe, Aidan Duffy, Sarah Mccormack, Michael Conlon

Articles

This paper presents validated real-time energy models for small-scale grid-connected PV-systems suitable for domestic application. The models were used to predict real-time AC power output from a PV system in Dublin, Ireland using 30-min intervals of measured performance data between April 2009 and March 2010. Statistical analysis of the predicted results and measured data highlight possible sources of errors and the limitations and/or adequacy of existing models, to describe the temperature and efficiency of PV-cells and consequently, the accuracy of power prediction models. PV-system AC output power predictions using empirical models for PV-cell temperature and efficiency prediction showed lower percentage …

The Applications And Limitations Of Printable Batteries, Matthew Delmanowski

Graphic Communication

This study focuses on the potential applications for printed batteries and how they could affect the printing industry. It also analyzes the main problems associated with manufacturing this technology and what needs to be done to overcome these issues. To find the answers to these questions, two methods of research were used. The first was through the elite and specialized interviewing of Dr. Scott Williams of Rochester Institute of Technology and Professor Nancy Cullins from Cal Poly. The second form of research was a common, yet useful, method called secondary research. This entailed looking at recent written research papers about …

Dc-Dc Converter For Harvesting Energy From An Exercise Bike, Henry Ureh, Chris Henry

Electrical Engineering

Create an efficient buck-boost converter that adapts to input voltage range from ~3.8V to 70V, and outputs 13.7V DC, the voltage required by a charge controller to charge a battery. The energy stored in the battery will be supplied back to the grid.

The cost of energy saved by the converter should eventually cover the initial price of the converter. The converter should help reduce the net power consumption of the exercise machines used in the Cal Poly gym

Health Prognisis Of Electronics Via Power Profiling, Jonathan Amilcar Cervantes

Open Access Theses & Dissertations

The objective of this research is to investigate a new approach for the early detection of latent defects in electronic devices in the field. Reliability is assessed through the non-traditional approach of recording and evaluating the power profile of electronic devices within a deterministic state of operation. Traditionally, measuring the quiescent current (Iddq) of a device has been employed in manufacturing tests to detect defective parts prior to deployment to the field. However, the monitoring of the deterministic power signature (i.e. boot up or during a self-test routine) has never been exploited to monitor the health of a device in …

Fpga-Based Design Of A Maximum-Power-Point Tracking System For Space A, Todd Persen

Electronic Theses and Dissertations

Satellites need a source of power throughout their missions to help them remain operational for several years. The power supplies of these satellites, provided primarily by solar arrays, must have high efficiencies and low weights in order to meet stringent design constraints. Power conversion from these arrays is required to provide robust and reliable conversion which performs optimally in varying conditions of peak power, solar flux, and occlusion conditions. Since the role of these arrays is to deliver power, one of the principle factors in achieving maximum power output from an array is tracking and holding its maximum-power point. This …