Engineering Commons^™

Efficiency Study Of A Hybrid Ac/Dc House, Eunice Dominique Solomon Santiago

Master's Theses

With the proliferation of residential-scale renewable energy sources and DC loads, it has become attractive to use residential DC electrical system that could offer benefits over the legacy residential AC electrical system. The Hybrid AC/DC house provides a sustainable alternative to preexisting residential electrical system by having both AC and DC buses. The DC bus facilitates the connection from DC sources to DC loads, whereas the AC bus interfaces AC sources to AC loads. The study develops the equations to calculate losses based on a model consisting of four main components: Multiple-Input Single-Output (MISO) converter, AC-DC converter, inverter, and DC-DC …

Design Of Class F-Based Doherty Power Amplifier For S-Band Applications, Kyle Chang

Master's Theses

Modern RF and millimeter-wave communication links call for high-efficiency front end systems with high output power and high linearity to meet minimum transmission requirements. Advanced modulation techniques, such as orthogonal frequency-division multiplexing (OFDM) require a large power amplifier (PA) dynamic range due to the high peak-to-average power ratio (PAPR). This thesis provides the analysis, design, and experimental verification of a high-efficiency, high-linearity S-band Doherty power amplifier (DPA) based on the Class F PA. Traditional Class F PAs use harmonically tuned output matching networks to obtain up to 88.4% power-added efficiency (PAE) theoretically, however the amplifier experiences poor linearity performance due …

Hypoxic Incubation Chamber, Simone Lisette Helfrich, Makenzie Nicole Jones

Master's Theses

This paper describes the design, manufacturing, and testing of a novel controllable hypoxic incubator with fully functional oxygen gas control and temperature control in a humid environment. On the current market, a majority of the few hypoxic incubators use pre-mixed gas that does not offer precise control over gas concentration. The objective for this project was to create a chamber that allows the user to set the O2 concentration to varying set points of % O2 while maintaining the chamber at a constant body temperature, CO2 level, humidity, and sterility. To start the project, multiple concepts were developed for the …

Design And Analysis Of A Discrete, Pcb-Level Low-Power, Microwave Cross-Coupled Differential Lc Voltage-Controlled Oscillator, Pavin Singh Virdee

Master's Theses

Radio Frequency (RF) and Microwave devices are typically implemented in Integrated Circuit (IC) form to minimize parasitics, increase precision and tolerances, and minimize size. Although IC fabrication for students and independent engineers is cost-prohibitive, an abundance of low-cost, easily accessible printed circuit board (PCB) and electronic component manufacturers allows affordable PCB fabrication.

While nearly all microwave voltage-controlled oscillator (VCO) designs are IC-based, this study presents a discrete PCB-level cross-coupled, differential LC VCO to demonstrate this more affordable and accessible approach. This thesis presents a 65 mW, discrete component VCO PCB with industry-comparable RF performance. A phase noise of -103.7 dBc/Hz …

Current-Source Dc-Dc Converter For Fiber-Optic Communication Systems, Jissell C. Jose

Master's Theses

In this thesis, a proof of concept for a current-source DC-DC converter for powering sensors used in an underwater communications system is presented. The proposed converter steps down an input current of 0.9 A to 0.625 A, while maintaining an output voltage of 24 V and output power of 15 W. The complete steady-state analysis and design of the proposed converter in its single-stage form is also explained in detail. Performance evaluation of the proposed converter was carried out using LTspice. Results of the simulation demonstrate that the design was able to produce average output current of 0.639 A at …

Design Of An Automotive Iot Device To Improve Driver Fault Detection Through Road Class Estimation, Matt Murray

Master's Theses

Unsafe driver habits pose a serious threat to all vehicles on the road. This thesis outlines the development of an automotive IoT device capable of monitoring and reporting adverse driver habits to mitigate the occurrence of unsafe practices. The driver habits targeted are harsh braking, harsh acceleration, harsh cornering, speeding and over revving the vehicle. With the intention of evaluating and expanding upon the industry method of fault detection, a working prototype is designed to handle initialization, data collection, vehicle state tracking, fault detection and communication. A method of decoding the broadcasted messages on the vehicle bus is presented and …

X-Band Rf Transmitter Design For Multi-Purpose Small Satellite Communication Operations, Omer F. Gumus

Master's Theses

This thesis provides a description of the analysis, design, and tests of an X-band RF Transmitter communication system for small satellites. X-band transmitter systems are becoming popular in the upcoming deep space missions. Most of the deep-space ground stations have been using X-band frequencies to receive or transmit signals. The X-band (<10 GHz) can offer lower atmospheric losses and up to a couple of Mbps data rates for multiple satellite operations. Nowadays, many small satellites have been using frequency bands such as VHF, UHF, L, and S-band frequencies for communication. From deep space to the ground station, the low-frequency ranges are inadequate in providing Mbps level data rates and enough bandwidth for deep space missions.

The main focus of this thesis was the development of the subsystems such as gain block amplifier, Mixer, Bandpass Filter, and RF power amplifier. The subsystems were designed separately, then they were connected together to perform an end-to-end system test. One of the thesis aims is to design …

A Nano-Drone Safety Architecture, Connor J. Sexton

Master's Theses

As small-form factor drones grow more intelligent, they increasingly require more sophisticated capabilities to record sensor data and system state, ensuring safe and improved operation. Already regulations for black boxes, electronic data recorders (EDRs), for determining liabilities and improving the safety of large-form factor autonomous vehicles are becoming established. Conventional techniques use hardened memory storage units that conserve all sensor (visual) and system operational state; and N-way redundant models for detecting uncertainty in system operation. For small-form factor drones, which are highly limited by weight, power, and computational resources, these techniques become increasingly prohibitive. In this paper, we propose a …

Integration Of Electrical Impedance Spectroscopy For Multichannel Cell Culture Measurement, Conard Chan

Master's Theses

ELECTROCHEMICAL IMPEDANCE SPECTROSCOPY (EIS) has been widely used to study the electrical properties of biological material due to its non-invasive nature and experimental reliability. However, most of the precision impedance analyzers used in EIS only provide single- or two-channel measurements which are inadequate for larger-scale multiplexed measurements, such as those found in modern microfluidic cell culture experiments. The Biomedical Microsystems Laboratory has developed a 16-channel cell culture platform with integrated electrode arrays for monitoring cell growth and electrical properties (i.e., the so-called “electrical phenotype”). In this paper, a system consisting of a 16-channel solid-state analog multiplexer (MUX)paired with a low-cost, …

Indoor Positioning Using Synchronized Ultrasonic Ofdma Signals, Julian Bartolone

Master's Theses

This paper proposes a method of short-range indoor localization using differential phase measurements of synchronized two-tone ultrasonic signals in an Orthogonal Frequency Multiple Access (OFDMA) scheme. This indoor positioning system (IPS) operates at an ultrasonic frequency of approximately 40kHz and synchronizes using an infrared signal. The OFDMA scheme allows for a receiver to process the signals from multiple transmitters continuously without the signals interfering with each other. The phases of the signals are measured using Goertzel Filters, allowing for low-complexity frequency content analysis. A MATLAB simulation using the proposed localization method is performed using four transmitter nodes in the corners …

Scalable Cognitive Radio Network Testbed In Real Time, Kevin Z. Yu

Master's Theses

Modern society places an increasingly high demand on data transmission. Much of that data transmission takes place through communication over the frequency spectrum. The channels on the spectrum are limited resources. Researchers realize that at certain times of day some channels are overloaded, while others are not being fully utilized. A spectrum management system may be beneficial to remedy this efficiency issue. One of the proposed systems, Cognitive Radio Network (CRN), has progressed over the years thanks to studies on a wide range of subjects, including geolocation, data throughput rate, and channel handoff selection algorithm, which provide fundamental support for …

Design And Modeling Of A Distributed Network For The Dc House Project, Lauren N. Rotsios

Master's Theses

This thesis covers the design and simulation of a model for a distributed network of DC Houses in MATLAB Simulink. The model will allow for sharing of power between houses within the network. The developed model consists of five separate DC House branches with local power generation. Each branch consists of a PV MPPT charge controller subsystem, a resistive load, and a bidirectional buck-boost converter subsystem. The high voltage side of every bidirectional buck-boost converter is connected together through the transmission line at a single high voltage DC bus. The performance of the individual components of the model is verified …

Design And Characterization Of Standard Cell Library Using Finfets, Phanindra Datta Sadhu

Master's Theses

The processors and digital circuits designed today contain billions of transistors on a small piece of silicon. As devices are becoming smaller, slimmer, faster, and more efficient, the transistors also have to keep up with the demands and needs of the daily user. Unfortunately, the CMOS technology has reached its limit and cannot be used to scale down due to the transistor's breakdown caused by short channel effects. An alternative solution to this is the FinFET transistor technology, where the gate of the transistor is a three dimensional fin that surrounds the transistor and prevents the breakdown caused by scaling …

Development Of A Portable Low-Moisture Food Pasteurization Device Using Rf Heating, Eric Jason Ohata

Master's Theses

Bacterial presence in low-moisture foods such as flour, cereals, baby formula, and spices, have become a concern due to sanitizing challenges. The food industry currently focuses on wet food sanitation as opposed to low-moisture foods because of bacteria’s inability to reproduce in low water activity media. Traditionally, food processing RF heating pasteurizes in mass quantities while an equivalent consumer device does not exist the market today. A consumer product would help eliminate food waste by providing an easy way to sanitize food and extend shelf life. The Portable Food Pasteurization (PFP) project is an interdisciplinary project involving the Electrical Engineering, …

First Order Self-Oscillating Class-D Circuit With Triangular Wave Injection, Matthew J. Carroll

Master's Theses

An investigation into performance improvements to the modulator stage of a class-D amplifier is conducted in this thesis. Two of the standard topologies, namely class-D open-loop pulse-width modulation (PWM), and the improved self-oscillating feedback system are benchmarked against a topology which includes both a hysteretic comparator in a feedback loop and triangle wave injection. Circuit performance is analyzed by comparing how the triangle injection circuit handles known issues with open-loop and self-oscillating circuits. Using this analysis, it is shown that the triangle injection topology offers an improved power supply rejection ratio relative to open-loop PWM and reduces distortion generated by …

Design Of An Ultra-Wideband Frequency-Modulated Continuous Wave Short Range Radar System For Extending Independent Living, Toai-Chi Nguyen

Master's Theses

Falls in the disabled and elderly people have been a cause of concern as they can be immobilized by the fall and have no way to contact others and seek assistance. The proposed frequency modulated continuous wave (FMCW) short range radar (SRR) system, which uses ultra-wideband (UWB) signals can provide immediate assistance by monitoring and detecting fall events. The unique characteristics of this system allow for a frequency-based modulation system to carry out triangulation and sense the location of the fall through the usage of a continuous chirp signal that linearly sweeps frequency. This project focuses on the development, design …

Early Wildfire Detection With Line Sensors, Virginia Yan

Master's Theses

Over the last few years, wildfires have become more devastating to communities as the fires are inevitably destructive to many homes, businesses, and ecosystems. Frequent wildfires also pose a significant threat to power grids and nearby residents as they can damage transmission lines and other electrical equipment, which in turn can cause major power shutdowns. Especially in western U.S., severe drought conditions and weather variability cause residents to become more vulnerable to wildfire disasters as their safety is threatened. We are incompetent to control the wildfires effectively despite existing advanced technologies. Hence, an algorithm based on energy conservation and heat …

Controller Modeling And Stability Analysis Of Multiple Input Single Output Dc-Dc Converter, Astha Adhikari

Master's Theses

This thesis entails the stability analysis of the Multiple Input Single Output (MISO) DC-DC converter developed for the DC House Project at Cal Poly. A frequency domain control system model of the MISO converter was designed and constructed using MATLAB Simulink. Transfer functions were derived and modeled for each stage of the converter to best fit the converter circuit system used in the original MISO circuit. Stability metrics such as overshoot, undershoot, rise time, phase margin and gain margin were measured to evaluate and analyze the stability of the converter. These metrics were measured with the original model including the …

Simulation Of An Sp8t 18 Ghz Rf Switch Using Smt Pin Diodes, Andre De Souza Vigano

Master's Theses

Radio frequency (RF) and microwave switches are widely used in several different applications including radar, measurement systems, telecommunications, and other areas. An RF switch can control a radar’s transmit vs. receive mode, select the operating band, or direct an RF signal to different paths. In this study, a single pole eight throw (SP8T) switch using only Surface Mount (SMT) components is designed and simulated in Keysight’s Advanced Design System (ADS). Single pole eight throw is defined as one input and eight possible outputs. A star network configuration with series-shunt PIN diode switches is used to create the 8-way RF switch. …

Iot Camera System For Monitoring Strawberry Fields, Simon Schoennauer

Master's Theses

A wireless imaging system for monitoring strawberry fields provides enough quality image data for computer vision algorithms to make meaningful yield predictions. This report contains a design for a wireless sensor network modified with mesh networking techniques to extend coverage range and a solar energy harvesting system to improve sensor node lifetime. A two hop system with six nodes is implemented in a laboratory environment validating the communication systems integrity over an 800’ range. Moving from a primary battery system to solar energy harvesting increases the module lifetime indefinitely.

Distance Estimation Using Ofdm Signals For Ultrasonic Positioning, Kyman Huang

Master's Theses

This paper describes a method of estimating distance via Time-of-Flight (TOF) measurement using ultrasonic Orthogonal Frequency Division Multiplexing (OFDM) signals. Using OFDM signals allows the signals and their sub-carriers to remain orthogonal to each other while continuously transmitting. This estimation method is based on the change of phase of a traveling wave as it propagates through a medium (air for ultrasonic signals). By using signals containing multiple tones, the phase change between each frequency component is slightly different. This phase difference is dependent on the distance traveled and can thus be used to estimate distance. This paper studies the impact …

The Design, Testing, And Analysis Of A Constant Jammer For The Bluetooth Low Energy (Ble) Wireless Communication Protocol, Aiku Shintani

Master's Theses

The decreasing cost of web-enabled smart devices utilizing embedded processors, sensors, and wireless communication hardware have created an optimal ecosystem for the Internet of Things (IoT). IEEE802.15.4, IEEE802.11ah, WirelessHART, ZigBee Smart Energy, Bluetooth (BT), and Bluetooth Low Energy (BLE) are amongst the most commonly used wireless standards for IoT systems. Each of these standards has tradeoffs concerning power consumption, range of communication, network formation, security, reliability, and ease of implementation. The most widely used standards for IoT are Bluetooth, BLE, and Zigbee. This paper discusses the vulnerabilities in the implementation of the PHY and link layers of BLE. The link …

A Novel Arc Welding Power Supply With Improved Power Factor Correction, Benjamin H. Tan

Master's Theses

This paper presents the design and development of a novel Arc Welding Power Supply utilizing a modified two-switch forward converter topology. The proposed design improves the power quality by improving power factor to near unity and reducing total harmonic distortion. State space analysis of the proposed circuit showed that the circuit followed a boost-buck input output relationship. Simulation of the circuit was first implemented in LTspice to verify the functionality of the new topology. Hardware implementation of the proposed design was built on a scaled-down prototype for a proof-of-concept of the new topology. The prototype specifications were created for a …

Performance Enhancement And Characterization Of An Electromagnetic Railgun, Paul M. Gilles

Master's Theses

Collision with orbital debris poses a serious threat to spacecraft and astronauts. Hypervelocity impacts resulting from collisions mean that objects with a mass less than 1g can cause mission-ending damage to spacecraft. A means of shielding spacecraft against collisions is necessary. A means of testing candidate shielding methods for their efficacy in mitigating hypervelocity impacts is therefore also necessary. Cal Poly’s Electromagnetic Railgun was designed with the goal of creating a laboratory system capable of simulating hypervelocity (≥ 3 km/s) impacts. Due to several factors, the system was not previously capable of high-velocity (≥ 1 km/s) tests. A deficient projectile …

Design, Modeling And Control Of A Two-Wheel Balancing Robot Driven By Bldc Motors, Charles T. Refvem

Master's Theses

The focus of this document is on the design, modeling, and control of a self-balancing two wheel robot, hereafter referred to as the balance bot, driven by independent brushless DC (BLDC) motors. The balance bot frame is composed of stacked layers allowing a lightweight, modular, and rigid mechanical design. The robot is actuated by a pair of brushless DC motors equipped with Hall effect sensors and encoders allowing determination of the angle and angular velocity of each wheel. Absolute orientation measurement is accomplished using a full 9-axis IMU consisting of a 3-axis gyroscope, a 3-axis accelerometer, and a 3-axis magnetometer. …

Cmos Design Of An 8-Bit 1ms/S Successive Approximation Register Adc, Ameya Vivekanand Ganguli

Master's Theses

Rapid evolution of integrated circuit technologies has paved a way to develop smaller and energy efficient biomedical devices which has put stringent requirements on data acquisition systems. These implantable devices are compact and have a very small footprint. Once implanted these devices need to rely on non-rechargeable batteries to sustain a life span of up to 10 years. Analog-to-digital converters (ADCs) are key components in these power limited systems. Therefore, development of ADCs with medium resolution (8-10 bits) and sampling rate (1 MHz) have been of great importance.

This thesis presents an 8-bit successive approximation register (SAR) ADC incorporating an …

Multiple Input, Single Output Dc-Dc Conversion Stage For Dc House, Jason Baltierrez

Master's Theses

n this thesis project, a proposed architecture for the multiple input, single output conversion stage for the DC House was designed, simulated, and tested. This architecture allows for multiple different input sources to be used to create a single higher power output source. The design uses a DC-DC boost converter with a parallelable output which has been demonstrated to allow increased total output power as a function of the number of input sources available. The parallelable output has been shown to distribute load amongst the input sources relatively closely to optimize the system. This approach is also desirable since it …

Smart Dc Wall Outlet Design With Improved Load Voltage Detection, Patrick Donovon Granieri

Master's Theses

A standard home in the United States has access to the 120V AC power grid for use with home appliances. Many electronics used at home are powered by a DC power supply, which loses energy in the conversion from AC power. The DC House project avoids any conversion between AC and DC by storing energy in batteries as DC power and supplying it directly to DC appliances. While AC systems feature a standardized output voltage, no such standard exists for DC systems. The Smart DC Wall Outlet solves this by automatically adjusting its output voltage to meet any required DC …

Designing A Simulator For An Electrically-Pumped Organic Laser Diode, Robert Hulbert

Master's Theses

Organic semiconductors provide an alternative set of basis materials to fabricate electronic devices like PN Junctions, LEDs, and FETs. These materials have several benefits over traditional inorganic semiconductors including their mechanical flexibility, reliance on renewable resources, and inexpensive large-scale manufacturability. Despite the contemporary device implementations with organic semiconductors, a solid-state electrically-pumped organic laser diode does not exist. However, organically-based lasers do exist by utilizing the organic material strictly for optical gain. The challenge occurs when charge carriers appear in the organic material. The charge carriers must reach a concentration such that population inversion occurs producing optical gain. However, between the …

Analog Single Sideband-Pulse Width Modulation Processor For Parametric Acoustic Arrays, Vikrant A. Marathe

Master's Theses

Parametric acoustic arrays are ultrasonic-based loudspeakers that produce highly directive audio. The audio must first be preprocessed and modulated into an ultrasonic carrier before being emitted into the air, where it will self-demodulate in the far field. The resulting audio wave is proportional to the double time-derivative of the square of the modulation envelope. This thesis presents a fully analog processor which encodes the audio into two Pulse Width Modulated (PWM) signals in quadrature phase and sums them together to produce a Single Sideband (SSB) spectrum around the fundamental frequency of the PWM signals. The two signals are modulated between …