Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 7 of 7
Full-Text Articles in Engineering
Power Transmission Line Fault Classification Using Support Vector Machines, Zhuokang Jia
Power Transmission Line Fault Classification Using Support Vector Machines, Zhuokang Jia
Masters Theses
Electrical transmission lines are prone to faults and failures. When a fault occurs, it is impossible most of the times to fix it manually. Many methods have been adopted in the past in order to serve the purpose as fault diagnosing application. In this thesis, I discuss the method of Support Vector Machine (SVM) for fault diagnosis. SVM has the edge of good generalization over other fault diagnosing applications because it is based on pattern recognize algorithms. The aim is to classify the type of fault in the lines. Furthermore, in this work, the current and voltage of each phase …
Application Of Wireless Power For Charging The Battery Of A Wireless Mouse, Jacob Keast, Vincent Jison
Application Of Wireless Power For Charging The Battery Of A Wireless Mouse, Jacob Keast, Vincent Jison
Electrical Engineering
Electronic devices are a part of all modern homes, but restricted by available outlets and the hassle of wires. With the modern wireless mouse, this is also the case. When the battery is low the consumer has several options: it is replaced with a new battery, it can be recharged using a USB wire, or the mouse is placed on a charging dock. This project provides an alternative to these options and allows the mouse’s battery to be charged via wireless inductive coupling. The wireless power charging system that was implemented in this project was successful in its ability to …
Design, Analysis, And Construction Of An Equal Split Wilkinson Power Divider, Logan J. Berens
Design, Analysis, And Construction Of An Equal Split Wilkinson Power Divider, Logan J. Berens
Master's Theses (2009 -)
The Wilkinson power divider is a well known device in the RF/microwave community used for splitting or combining signals. It is composed of simple transmission lines and a resistor, and takes advantage of the properties of quarter-wavelength transmission line sections to provide ideal power divider characteristics. Three different equal split Wilkinson power dividers are designed to operate near 1800 MHz and constructed using typical microstrip fabrication techniques. The three power dividers each feature a unique design to help determine how the microstrip layout can impact isolation and return loss. A circuit analysis of the general Wilkinson power divider schematic is …
Design Of Dc Light Bulb For The Dc House Project, Kent Chin Liang
Design Of Dc Light Bulb For The Dc House Project, Kent Chin Liang
Master's Theses
This thesis focuses on the design and implementation of an economical and energy efficient DC Light Bulb for the DC House Project. For the DC lighting system, emphasis is on the DC-DC LED driver, dimmer circuit, LED lighting array, and physical packing design. In this paper, a DC Light Bulb is designed, simulated, and tested to operate at a wide input voltage ranging from 24 VDC to 72 VDC, to be fully dimmable using pulse-width modulation technique, and to produce lumination intensities equivalent to a standard 100 W A19 incandescent light bulb at one-tenth the total power consumption. The DC …
Portable Solar Powered Charging Station, Jordan Bonner
Portable Solar Powered Charging Station, Jordan Bonner
Electrical Engineering
The portable solar powered charging station uses a solar powered mat that can be folded for portability. The device has the ability to charge small electronics during both day and night. When sunlight is available, the charger charges two C batteries in series and at the same time it charges any electronic device that can be connected via USB or cigarette lighter. At night the charger will charge the same electronic devices from the onboard batteries. The charging station must be able to interface with electronic devices using USB and a car cigarette lighter to charge the device’s battery.
A Gps-Based Mobility Power Model For Military Vehicle Applications, George William Bozdech
A Gps-Based Mobility Power Model For Military Vehicle Applications, George William Bozdech
Masters Theses
In recent years, military vehicles have been equipped with hybrid, diesel-electric drives to improve fuel efficiency and stealth capabilities. These vehicles require an accurate estimate of the power duty cycles during distinct operating conditions. To meet this demand, a GPS-based mobility power and duty cycle analysis is one approach to predict the power requirements of on-road and off-road vehicles. The dynamic vehicle parameters needed to estimate the forces developed during locomotion are determined from the GPS tracking data, and these forces include the following: the motion resistance, gravitational, linear inertia, rotational inertia, and aerodynamic drag. The motion resistance force generated …
Modeling And Analysis Of A Photovoltaic System With A Distributed Energy Storage System, Anthony Winston Ma
Modeling And Analysis Of A Photovoltaic System With A Distributed Energy Storage System, Anthony Winston Ma
Master's Theses
As California continues to integrate more renewable energy into its electrical system, the state has experienced a corresponding rise in photovoltaic system installations. PV arrays are a unique source of power generation in that they are affected by the location of the sun, shading, and temperature changes. These characteristics make solar one of the most highly variable forms of renewable energy. In order to improve solar power’s consistency, PV systems require a supplemental source of power. The primary focus of this paper is to determine if distributed energy storage systems can be used to reduce the effect of solar intermittency. …