Engineering Commons^™

Development Of Fully Printed And Flexible Strain, Pressure And Electrochemical Sensors, Dinesh Maddipatla

Masters Theses

In recent years, considerable research has been put into the development of printed electronics (PE) as well as the best ways to effectively and efficiently print electronic devices on flexible substrates. This thesis focuses majorly on the design and fabrication of novel flexible sensors using conventional printing processes.

Initially, a flexible printed strain gauge was fabricated successfully on a flexible paper substrate using flexography printing process. Silver (Ag) ink was printed on the paper substrate as metallization layer. The performance of the printed device was investigated by subjecting the strain gauge to a 3-point bend test, with a displacement of …

Cmos Based Impedance Sensing, Jinlong Gu

Masters Theses

This thesis focuses on a compact, low power circuit design for biological cell impedance sensing. Cell impedance sensing provides a new way to diagnose the cancers. Experiments done previously have shown that cancer cells have lower impedance than the normal cells, due to the thinner membrane of cancer cells. Traditional methods of cancer diagnosis require special chemicals, skilled personnel, and take long time to obtain the results. Two circuit structures are proposed in this work. One is a silicon cochlea based architecture. The other one is a current mode lock-in amplifier. Both of these two structures are able to measure …

Variation Aware Placement For Efficient Key Generation Using Physically Unclonable Functions In Reconfigurable Systems, Shrikant S. Vyas

Masters Theses

With the importance of data security at its peak today, many reconfigurable systems are used to provide security. This protection is often provided by FPGA-based encrypt/decrypt cores secured with secret keys. Physical unclonable functions (PUFs) use random manufacturing variations to generate outputs that can be used in keys. These outputs are specific to a chip and can be used to create device-tied secret keys. Due to reliability issues with PUFs, key generation with PUFs typically requires error correction techniques. This can result in substantial hardware costs. Thus, the total cost of a $n$-bit key far exceeds just the cost of …

Extrinsic Effects On Heat And Electron Transport In Two-Dimensional Van-Der Waals Materials- A Boltzmann Transport Study, Arnab K. Majee

Masters Theses

Two-dimensional van der Waals materials have been a subject of intense research interest in recent years. High thermal conductivity of graphene can be utilized for many thermal management applications. In spite of possessing very high electron mobility, graphene can’t be used as transistors because of the absence of band gap; however transition metal dichalcogenides are another class of two-dimensional van der Waals materials with inherent band gap and show a great promise for future nanoelectronic applications. But in order to tailor these properties for commercial applications, we should develop a better understanding of the effect of extrinsic factors like size, …

Improving Efficiency Of Thermoelectric Devices Made Of Si-Ge, Si-Sn, Ge-Sn, And Si-Ge-Sn Binary And Ternary Alloys, Seyedeh Nazanin Khatami

Masters Theses

Thermoelectric devices with the ability to convert rejected heat into electricity are widely used in nowadays technology. Several studies have been done to improve the efficiency of these devices. However, because of the strong correlation between thermoelectric properties (electrical conductivity, Seebeck coefficient, and thermal conductivity including lattice and electron counterpart), improving ZT has always been a challenging task. In this study, thermal conductivity of group IV-based binary and ternary alloys such as SiGe, SiSn, GeSn, and SiGeSn has been studied. Phonon Boltzmann Transport Equation has been solved in the relaxation time approximation including intrinsic and extrinsic (in the presence of …

Review And Characterization Of Gallium Nitride Power Devices, Edward Andrew Jones

Masters Theses

Gallium Nitride (GaN) power devices are an emerging technology that have only recently become available commercially. This new technology enables the design of converters at higher frequencies and efficiencies than those achievable with conventional Si devices. This thesis reviews the characteristics and commercial status of both vertical and lateral GaN power devices from the user perspective, providing the background necessary to understand the significance of these recent developments. Additionally, the challenges encountered in GaN-based converter design are considered, such as the consequences of faster switching on gate driver design and board layout. Other issues include the unique reverse conduction behavior, …

The Design And Validation Of A Wireless Bat-Mounted Sonar Recording System, Jeremy Joseph Langford

Masters Theses

Scientists studying the behavior of bats monitor their echolocation calls, as their calls are important for navigation and feeding, but scientist are typically restricted to ground-based recording. Recording bat calls used for echolocation from the back of the bat as opposed to the ground offers the opportunity to study bat echolocation from a vantage otherwise only offered to the bats themselves. However, designing a bat mounted in-flight audio recording system, (bat-tag), capable of recording the ultra-sound used in bat echolocation presents a unique set of challenges. Chiefly, the bat-tag must be sufficiently light weight as to not overburden the bat, …

Evaluating Features For Broad Species Based Classification Of Bird Observations Using Dual-Polarized Doppler Weather Radar, Sheila Werth

Masters Theses

Wind energy is one of the fastest-growing segments of the world energy market; however, wind energy facilities can have detrimental effects on wildlife, especially birds and bats. The ability to monitor vulnerable species in the vicinity of proposed wind sites could enable site selection that favors more vulnerable species, but current monitoring tools lack this classification capability. This work analyzes polarimetric and Doppler measurements of migrating birds for species based variation.

A novel two stage feature extraction technique was developed to enable comparison between birds. Stage one involves mapping time changing radar measurements to the birds behavioral state in time …

Localization, Visualization And Evacuation Guidance System In Emergency Situations, Jingyan Tang

Masters Theses

Urban search and rescue is needed for a variety of emergencies or disasters, including tornadoes, floods, dam failures, technological accidents, and terrorist activities. The efficiency to save people is becoming very important. With the development of the technology, people are trying to find a better way to help people get out of the dangerous places as soon as possible. DIORAMA system has been proposed to help with this problem and turns out very successful on improving efficiency during emergency situation. However, the current DIORAMA system is not perfect for all scenarios, for example, there are some outdoor environments do not …

A Haptic Surface Robot Interface For Large-Format Touchscreen Displays, Mark Price

Masters Theses

This thesis presents the design for a novel haptic interface for large-format touchscreens. Techniques such as electrovibration, ultrasonic vibration, and external braked devices have been developed by other researchers to deliver haptic feedback to touchscreen users. However, these methods do not address the need for spatial constraints that only restrict user motion in the direction of the constraint. This technology gap contributes to the lack of haptic technology available for touchscreen-based upper-limb rehabilitation, despite the prevalent use of haptics in other forms of robotic rehabilitation. The goal of this thesis is to display kinesthetic haptic constraints to the touchscreen user …

A General Code To Simulate The Effect Of Indirect Lightning On Overhead Lines Using Emtp-Type Programs, Hasan Jameel Hasan

Masters Theses

In this thesis, a general code is obtained to allow the simulation of the transient response of transmission lines excited by a nearby lightning stroke using EMTP–type programs, namely PSCAD and ATP.

Initially, the frequency domain modeling of single phase and multiconductor transmission lines is described and assessed by means of several application examples. As a second stage, the transmission line model is used to implement an illuminated transmission line model (line excited by an electromagnetic field excitation) using Taylor’s formulation. Then, a general code is developed in MATLAB to obtain the response of a field excited line; this effect …

Total Harmonics Distortion Reduction Using Adaptive, Weiner, And Kalman Filters, Liqaa Alhafadhi

Masters Theses

Total harmonics distortion is one of the main problems in power systems due to its effects in generating undesirable issues in power quality. These effects include heating (in transformers, capacitors, motors, and generators), disoperation of electronic equipment, incorrect readings on meters, disoperation of protective relays, and communication interference. Besides these problems, harmonics affect the power quality in both transmission and distribution systems. Different techniques have been used to mitigate the effects of harmonics. These techniques include; passive filters, active power filter, artificial intelligent, and adaptive selective harmonics reductions. Each method has some advantage and disadvantage. This thesis presented new models …

Development Of Strain And Pressure Sensors On Flexible And Stretchable Platforms, Mohammed Mudher Mohammed Ali

Masters Theses

The capability of the human brain to operate in conjunction with human senses and muscles enables us to become powerful autonomous beings. By using these organs, humans can interact with the surrounding environment. Similarly, the combination of sensors with the signal processing of modern electronics enables the interaction with the non-electrical environment.

In this thesis, the work focuses on the design and fabrication of flexible and stretchable sensors which have been receiving an increased interest for applications such as human body movement, tracking in the biomedical industry, object detection, fingerprint sensor as well as for monitoring deformations or structural changes …

Sic Band Gap Voltage Reference For Space Applications, Charles Kenneth Roberts

Masters Theses

Electronics for space applications can experience wide temperature swings depending on orientation towards stars and duty cycle of propulsion systems. Energy on satellites primarily comes from radiological thermal generators and / or solar panels. This requires space electronic applications to be energy efficient and have high temperature tolerance. As a result, space electronic systems use high efficiency SMPS [switching mode power supplies].

Currently, there exists SiC [silicon carbide] based electronics that is state of the art for high temperature applications. Commercial manufacturers at this time produce SiC Power MOSFETs [Metal Oxide Semiconductor Field Effect Transistors], which are the switching element …

Dynamic Extruder Control For Polymer Printing In Big Area Additive Manufacturing, Alex Christopher Roschli

Masters Theses

Big Area Additive Manufacturing (BAAM) is 3D Printing on a large scale and can be used to create structures on the scale of cars and houses. Scaling up 3D printing to BAAM size meant fundamentally altering the traditional fused deposition modeling process by switching from a filament to a pellet material feed. This meant switching from a stepper motor extruder to a servo driven screw extruder. While increasing the throughput of the system, this new extruder increases the overall complexity. Effective control of the system is paramount to the success of BAAM enabling it to effectively scale in speed in …

Internal Fault Location In Transformer Windings, Samir Yehya Abed-Alkareem Alzekri

Masters Theses

Power transformers are one of the most important components in electrical power systems. During their lifetime they are exposed to various electrical faults which are originated from transient overvoltages, electromagnetic forces due to over-currents, ageing, etc.

Internal winding faults are among the most common causes of transformer failure. Once a fault occurs, a fast an efficient method for its detection and location is required to avoid further delays in the network operation. This paper introduces a simple method for the location of internal winding faults. This method is based on time domain terminal measurements of wave propagation along the winding. …

A Parameterized Implementation Of A Hybrid Fuzzy Boolean Finite State Machine Using An Fpga, Sean T. Fuller

Masters Theses

A fuzzy system based on the extended Hybrid Fuzzy Boolean Finite State Machine (HFBFSM) model is designed and implemented in a Xilinx Zynq® all programmable System on Chip (SoC). The system allows for a single dominant crisp state and multiple non-dominant states to be activated simultaneously. A method is proposed to calculate the degree of membership of non-dominant states, β, by the distance of defuzzified fuzzy inputs to state transition trigger mechanisms.

The HFB-FSM is was realized by the author using custom logic written in VHDL (Very High Speed Integrated Circuit (VHSIC) Hardware Description Language) in the Programmable Logic (PL) …

Integrated Solar Technologies With Outdoor Pedestrian Bridge Superstructure Decking, Richard K. Racz

Masters Theses

Solar technology has been a major topic in sustainable design for many years. In the last five years, however, the solar technology industry has seen a rapid growth in installations and technological advances in cell design. Combined with a rapidly declining overall system cost, the idea of introducing solar technology into a wider range of applications is becoming a focus for engineers and scientists around the world. So many variables which alter solar energy production, such as the sun and surrounding environment, determine whether a solar design is beneficial. This thesis presents a bridge deck surface integrated with solar cells …

Processor Temperature And Reliability Estimation Using Activity Counters, Mayank Chhablani

Masters Theses

With the advent of technology scaling lifetime reliability is an emerging threat in high-performance and deadline-critical systems. High on-chip thermal gradients accelerates localised thermal elevations (hotspots) which increases the aging rate of the semiconductor devices. As a result, reliable operation of the processors has become a challenging task. Therefore, cost effective schemes for estimating temperature and reliability are crucial. In this work we present a reliability estimation scheme that is based on a light-weight temperature estimation technique that monitors hardware events. Unlike previously pro- posed hardware counter-based approaches, our approach involves a linear-temporal-feedback estimator, taking into account the effects of …

Seamless Application Delivery Using Software Defined Exchanges, Divyashri Bhat

Masters Theses

One of the main challenges in delivering content over the Internet today is the absence of a centralized monitoring and control system [38]. Software Defined Networking has paved the way to provide a much needed control over network traffic. OpenFlow is now being standardized as part of the Open Networking Foundation, and Software Defined Exchanges (SDXes) provide a framework to use OpenFlow for multi-domain routing. Prototype deployments of Software Defined Exchanges have recently come into existence as a platform for Future Internet Architecture to eliminate the need for core routing technology used in today’s Internet. In this work, we look …

Event-Sampled Direct Adaptive Neural Network Control Of Uncertain Strict-Feedback System With Application To Quadrotor Unmanned Aerial Vehicle, Nathan Szanto

Masters Theses

"Neural networks (NNs) are utilized in the backstepping approach to design a control input by approximating unknown dynamics of the strict-feedback nonlinear system with event-sampled inputs. The system state vector is assumed to be unknown and an observer is used to estimate the state vector. By using the estimated state vector and backstepping design approach, an event-sampled controller is introduced. As part of the controller design, first, input-to-state-like stability (ISS) for a continuously sampled controller that has been injected with bounded measurement errors is demonstrated and, subsequently, an event-execution control law is derived such that the measurement errors are guaranteed …

Construction And Validation Of Tl-Ipm Generator, Jamaluddin Mohammad

Masters Theses

"Hydrokinetic energy is one of the potential sources of energy that can be extracted and converted to electrical energy using linear generator. This work discusses about construction and validation of tubular linear internal permanent magnet (TL-IPM) generator, a kind of linear generator. The generator could produce electricity by converting linear motion generated from vortex induced vibrations induced due from a flowing fluid, such as a river. A simulation model of the generator is created using Ansoft's Maxwell software, which uses finite element analysis to perform electromagnetic analysis of the generator. Then a practical generator was built and tested. The results …

A Cost Benefit Analysis Of Sst Based Volt-Var Control, Guruprasad Ramani

Masters Theses

"The overall objective of this thesis work is to improve system power quality with the help of solid state transformers (SSTs). Two methods to improve the system power quality are explored: a) achieving a unity power factor at all the load buses, and b) improving the system voltage profile to meet a desired voltage regulation requirement of 0.95

Managing Risks Of Market Price Uncertainty For A Microgrid Operation, Sriram Raghavan

Masters Theses

"After deregulation of electricity in the United States, the day-ahead and real-time markets allow load serving entities and generation companies to bid and purchase/sell energy under the supervision of the independent system operator (ISO). The electricity market prices are inherently uncertain, and can be highly volatile. The main objective of this thesis is to hedge against the risk from the uncertainty of the market prices when purchasing/selling energy from/to the market. The energy manager can also schedule distributed generators (DGs) and storage of the microgrid to meet the demand, in addition to energy transactions from the market. The risk measure …

De-Embedding Method For Electrical Response Extraction Of Through-Silicon Via (Tsv) In Silicon Interposer Technology And Signal Integrity Performance Comparison With Embedded Multi-Die Interconnect Bridge (Emib) Technology, Qian Wang

Masters Theses

"Traditional two-dimensional system-in-package (2D SiP) can no longer support the scaling of size, power, bandwidth, and cost at the same rate required by Moore's Law. Three-dimensional integrated circuits (3D-ICs), 2.5D silicon interposer technology in which through silicon vias are widely used, are implemented to meet these challenges. Embedded multi-die interconnect bridge (EMIB) technology are proposed as well.

In Section 1, a novel de-embedding method is proposed for TSV characterization by using a set of simple yet efficient test patterns. Full wave models and corresponding equivalent circuits are provided to explain the electrical performance of the test patterns clearly. Furthermore, broadband …

Thrust Sensing For Small Uavs, Christopher Scott Marchman

Masters Theses

"Unmanned aerial vehicles (UAVs) have become prevalent in both military and civilian applications. UAVs have many size categories from large-scale aircraft to micro air vehicles. The performance, health, and efficiency for UAVs of smaller sizes can be difficult to assess and few associated instrumentation systems have been developed. Thrust measurements on the ground can characterize systems especially when combined with simultaneous motor power measurements. This thesis demonstrates the use of strain measurements to measure the thrust produced by motor/propeller combinations for such small UAVs. A full-bridge Wheatstone circuit and electrical resistance strain gauges were used in conjunction with constant-stress cantilever …

Study Jitter Amplification Of A Passive Channel And Investigation Of S₂₁ Magnitude Extraction Methodologies Using A Pattern Generator And Oscilloscope, Xinyun Guo

Masters Theses

"Recently the clock channel jitter amplification has been observed in several publications. Currently in many high-speed I/O systems, to avoid the cost and the complex clock recovery circuit design, people use traces forwarding clock signal from transmitting IC to receiving IC. When these clock traces are long enough, the amount of attenuation will induce not only inter-symbol-interference (ISI) but also modulate with the input jitter. Eventually it will lead some type of jitter been amplified after the channel. Similarly, the high speed communication channel (data channel) will also face this issue. Since there are no studies on the jitter amplification …

Design Methodology For Behavioral Surface Roughness Modeling And High-Speed Test Board Design, Xinyao Guo

Masters Theses

"A behavioral model is introduced, which can predict low-loss and low surface roughness transmission line time- and frequency- domain performances. High data rates push for better performance of PCB transmission lines. However, the roughness of copper foil has a considerable impact on the signal integrity performance of transmission lines at high data rates and long propagation distance. Existing models for low-loss transmission line surface roughness are inadequate. A new behavioral model to represent the surface roughness has been developed. The model is applied in the design process by adding a dispersive term to the bulk dielectric permittivity to represent the …

Measurements And Simulation Of Conductor-Related Loss Of Pcb Transmission Lines, Oleg Kashurkin

Masters Theses

"With continuously increasing data rates Signal Integrity (SI) problems become more and more challenging. One of the main issues in high-speed data transfer is the frequency-dependent loss of transmission lines. This thesis is dedicated to conductor-related loss mechanisms in printed circuit board (PCB) transmission lines.

This thesis provides the experimental investigation of conductor properties used for fabrication of PCBs. Particularly, the resistivity and conductivity along with the temperature coefficients of eleven copper types is measured and reported. A four probe measurement technique is used. Results were verified by two independent measurements and show discrepancy of less than 0.5%.

Another major …

Application Of Embedded Frequency Selective Surfaces For Structural Health Monitoring, Dustin Franklin Pieper

Masters Theses

"This thesis proposes the use of Frequency Selective Surfaces (FSSs) as an embedded structural health monitoring (SHM) sensor. FSSs are periodic arrays of conductive elements that filter certain frequencies of incident electromagnetic radiation. The behavior of this filter is heavily dependent on the geometry of the FSS and local environment. Therefore, by monitoring how this filtering response changes when the geometric or environmental changes take place, information about those changes may be determined. In previous works, FSS-based sensing has shown promise for sensing normal strain (a stretching or compressing geometrical deformation). This concept is extended in this thesis by investigating …