Engineering Commons^™

Residential Grid-Tied With Battery Backup Photovoltaic System, Thomas Stobuagh

Electrical Engineering

When power outages occur, many homes are left without power for some time as they are dependent on the power grid. This project aims to design a residential grid tied battery backup photovoltaic system that will provide up to 7.2kW in an area that gets 5.36-5.49 kWh/m2/day [1] to support a home with an average daily usage of 28.4 kWh/day. To effectively use this system the house remains connected to the electric utility at all times, so any power needed above what the solar system can produce is simply drawn from the utility. It includes battery backup or uninterruptible power …

Single-Phase High Efficiency Motor Testing, Marc Henry Perez

Electrical Engineering

A three-phase induction motor has higher efficiency than the single-phase motor counterpart. It is possible to run a three-phase motor with a single-phase source to develop a single-phase high efficiency system. The single-phase high efficiency motor, or SHE-motor, uses capacitor banks to operate at a balanced three phase induction motor using a single phase source. Unfortunately, this design has been limited, as it can only be balanced for one load configuration at a time. This provides the system to have maximum system performance. Due to this limitation in operations, it has proven to be non-ideal in commercial applications. It is …

Application Of Wireless Power For Charging The Battery Of A Wireless Mouse, Jacob Keast, Vincent Jison

Electrical Engineering

Electronic devices are a part of all modern homes, but restricted by available outlets and the hassle of wires. With the modern wireless mouse, this is also the case. When the battery is low the consumer has several options: it is replaced with a new battery, it can be recharged using a USB wire, or the mouse is placed on a charging dock. This project provides an alternative to these options and allows the mouse’s battery to be charged via wireless inductive coupling. The wireless power charging system that was implemented in this project was successful in its ability to …

Active Diesel Soot Measurement By Laser Opacity, Jonathan Audish, Brian Ko, Edward Ma, Travis Mcdaniel

Electrical Engineering

This project looks into understanding the concentration of soot being omitted by a diesel engine through the creation of an innovative opacity sensor. The system contains a receiver circuit implementing a photodiode, laser with wavelength of 405±10nm, and a microcontroller with analog-to-digital (A/D) converter. As the laser pulsates, the microcontroller collects and processes the data to calculate the amount of soot within the exhaust system. The opacity sensor in our tests will be used on an Isuzu 1.9 liter diesel engine. The elegant design of the system can be integrated into conventional manufacturing molding or casting processes for new exhaust …

Energy Harvesting Of Human Kinetic Movement, David Marusiak, Julia Carrillo

Electrical Engineering

Development of kinetic energy scavenging applications from the human body necessitates additional research to assist in designating a mounting position for a potential device. A data acquisition system adequately provides a parametric average power comparison among four locations on the body (waist, upper arm, hand, and calf) for both a male and female subject. Experimentally, the hand-held device provided the highest average power. Thus, subsequent investigation at set speeds provides further analysis of the output’s characteristically linear behavior. The physical energy-harvesting device features a plastic tube casing wrapped with the stationary coiled wire through which a neodymium magnet oscillates. While …

Radio Link Analysis And Characterization Of Past And Future Cal Poly Cubesats, Brian Gilbert Tubb

Electrical Engineering

Cal Poly's satellites design team, PolySat, has three satellites in Low Earth Orbit (LEO) and four more planned to launch within the next two years. Radio communication of past and current orbiting satellites has been an exercise in frustration, prompting significant research into the satellite-side of the radio link by several other Senior Projects and Thesis papers. However, minimal effort has been spent on evaluating why these problems were discovered only once the satellites reached orbit. This paper details the downfalls of relying heavily on link budgets and improper long range test setups, then experimentally determines the sensitivity of PolySat's …

3.5 To 30 Mhz Automatic Antenna Impedance Matching System, William Blodgett

Electrical Engineering

Two-way communications using 3 to 30 MHz, high-frequency (HF) radio, also known as shortwave radio, provides worldwide coverage with no infrastructure required between stations. Amateur or “Ham” radio operators apply this advantage to long distance communications and to provide disaster relief communications. Optimum frequencies for long distance propagation are time-of-day variant necessitating an operating frequency range of 3 to 30 MHz. HF half wave dipole antenna length varies from 15 to 150 ft over this range. Fixed-length antenna impedance varies with frequency due to physical dimension dependent capacitance and inductance. Maximum transmitter to antenna power transfer occurs when the transmission …

Optical Mode Study Of Galium Nitride Based Laser Diodes, Douglas Cattarusa

Electrical Engineering

This paper focuses on the optical mode analysis of laser diodes to improve light emission. Under the mode analysis, we compare the optical confinement factor (OCF) percentage of the emitting light from the LDs. There are two structures which we analyze: a basic GaN waveguide structure and an InGaN waveguide structure. The second structure has additional InGaN waveguides and is analyzed under two additional design variations: the concentration of Indium and the thickness of the top waveguide layer. The results of this study indicate introducing InGaN waveguide layers correlates with lower order modes (zero and first order) and increase the …

An Overview Of Binary Arithmetic Architectures & Their Implementation In Dsp Systems, Joseph Waddell

Electrical Engineering

This project gives looks at different binary adder and multiplier architectures and how they are implemented in a DSP system as a digital filter. Testing is performed in the Digilent Nexys2 FPA board and filters are implemented using various realizations including normal direct form I and cascade direct forms I and II. Signal filtering is performed in real time at various frequencies and results are provided on an oscilloscope and with a stereo speaker.

Portable Solar Powered Charging Station, Jordan Bonner

Electrical Engineering

The portable solar powered charging station uses a solar powered mat that can be folded for portability. The device has the ability to charge small electronics during both day and night. When sunlight is available, the charger charges two C batteries in series and at the same time it charges any electronic device that can be connected via USB or cigarette lighter. At night the charger will charge the same electronic devices from the onboard batteries. The charging station must be able to interface with electronic devices using USB and a car cigarette lighter to charge the device’s battery.

802.15.4 Low Intermediate Frequency Radio Receiver, Sanjay Avasarala

Electrical Engineering

This project involves the design, building, and testing of a low intermediate frequency 802.15.4 receiver that uses an FPGA to perform final demodulation to baseband.

Cell Phone Charger For The Dc House Project, Andrew Hefner, Antonio Magdaleno

Electrical Engineering

The goal of this project is to create a multiple output cell phone charger for the DC House project. The cell phone charger is essentially a DC-DC converter. The converter takes an input of 48 volts from the outlet in the DC House and decreases the voltage level to 5 volts; the input voltage level of all cellular devices. By designing an isolated flyback converter with initial specification in LTSpice simulation software, a converter was created. By monitoring the input and output voltage and current using the multi-meters and electronic load, we determined the charger to be 71% efficient when …

High Efficiency Audio Amplifier, Grant Moore

Electrical Engineering

This project combines the advantages of high efficiency of power electronics with the existing high fidelity of audio amplifiers. The result will be functionally equivalent to existing amplifiers but will use considerably less energy. A complete system was designed, simulated, built and tested in a period of three quarters. The end result is an amplifier that functions, but would not be suitable for commercial marketing. Suggestions to improve the performance are provided.

"Auto-Tuned" Stereo, Daniel Montes

Electrical Engineering

The purpose of this project is to determine the capability of introducing delay and gain to audio signals to synthesize a “tuned” experience. The project uses audio operational amplifiers, field effect transistors, a class D amplifier, microphones, speakers, a 32-bit microcontroller for design and testing. When implementing the MOSFET into the all pass filter, the phase delay occurs by varying the transistor resulted in minimal change in phase. MOSFETs are used as variable resistors to vary the phase change and gain. By modifying the gain the synthesized distance from each speaker can be adjusted. Varying the phase change provides the …

Control System For Glucose Detector System, David Smith

Electrical Engineering

In this paper I design and test on a prove of concept level a control/timing circuit for a blood glucose detector built in a previous senior project. The specifications of the design given are to properly power the detector with a low power source. The design is completed on a transistor level basis using Cadence Virtuoso Software. The system is design from the ground up; designing, building, and testing smaller circuits first then combined into increasingly larger circuits till the completed circuit is finished. The design used to based off of the 555 Timer and uses differential pairs, CMOS designed …

Music Driven Graphical Visualization System, Glenn Bruner

Electrical Engineering

In today’s society, we are able to enjoy listening to music on an assortment of high-tech devices such as home computers, or multimedia players, or personal audio players. A common characteristic of typical audio media players is that they lack the ability to provide visual stimulation in addition to the provided audio stimulus. Large public events, such as concerts, could be enhanced if they included visual effects in addition to audio stimulation. The goal of this project is to provide a graphical visualization that is automatically synchronized to an audio signal with a goal of enhancing the overall musical experience. …

Ultra-Capacitor Based Electric Bicycle Regenerative Braking System, Alex C. Bronstein

Electrical Engineering

An experimental regenerative braking system was designed and installed on an electric bicycle. The braking system relies on electric double-layer capacitors (EDLC), also known as ultracapacitors, to store the braking energy from the electric bicycle hub motor.

Pulsed Class-G Rf Amplifier System, Kevin Maulhardt, Kevin Haskett

Electrical Engineering

No abstract provided.

Printed Electroluminescent Display, Christopher (Chris) James Nixon, Veronica Kopp

Electrical Engineering

Electroluminescent displays are part of an emerging technology known as printed electronics. Most identify printed electronics with purely electronic purposes such as the Radio frequency identification (RFID). Now the electronics and graphic communication industries have come together to create of new forms of products that interact with customers. Flexible, electronic circuits use functional inks and traditional printing methods such as screen printing, gravure, and inkjet. Printed electronics are perfect for low performance applications, such as displays, labels, clothing and batteries. This paper focuses on creating an interactive electroluminescent (EL) display. In selling a product, displays are important because most customers …

All-In-One Aprs Transmitter, Justin Kenny

Electrical Engineering

The Automatic Packet Reporting System (APRS) is a digital radio system that allows transmission of data using an analog FM radio link. APRS allows position, brief messages, and other data to be distributed across a network, independent of infrastructure, making it ideal for applications such as search and rescue, asset management, and event tracking, while maintaining low cost and operating even when cellular and internet services are unavailable. This project encompasses the design, build, and test of a compact, low-cost APRS transmitter, which will include a 5W radio, GPS, and LCD-based user interface, to allow full utilization of APRS.

Digital Graphic Equalizer Implemented Using An Fpga, Anthony Giardina

Electrical Engineering

A graphic equalizer is a device that adjusts the tonal quality of an audio signal. When sound is converted from a digital format to analog sound waves, there are amplification and transducing steps in-between the two formats. Common devices to perform these tasks are speakers, amplifiers, DACs, etc. Many of these devices exhibit a non-uniform frequency response over the range of human hearing. Thus, it is possible that certain frequency ranges of the audio signal will be amplified and others will be attenuated. To counteract this, an audio equalizer can be used to boost and attenuate certain frequency ranges within …

Hardware And Software Study Of Active Noise Cancellation, Riggi Aquino, Jacob Lincoln

Electrical Engineering

Noise cancellation involves removing an unwanted noise while keeping the source sound. The source sound may consist of speech, music played from a device such as an iPod or a computer, or no sound at all. The objective of this project is to study the process of noise cancellation both as hardware and as software. The hardware will consist of building a noise cancelling circuit that uses headphones as an output, a microphone to pick up the noise to be cancelled and, if desired, a source sound. The software portion of the experiment will use MATLAB to simulate the hardware …

Dc House Model Design And Construction, Mark Cabaj

Electrical Engineering

Approximately 1.6 billion people currently live without electricity. The only sensible solution to their energy problems is the use of renewable energy in an off-grid, autonomous home which is powered directly by direct current, rather than alternating current coming from a power line, which probably cannot be found nearby. The purpose of this project is to construct a prototype of the DC House. More specifically, this project focuses on the development and construction of the power distribution system of the DC House. The system will be put in place starting from the source side model down to the load side …

Foce Intermodule Communications System, Roland Quiros

Electrical Engineering

Done in conjunction with Chad Kecy of the Monterey Bay Aquarium Reasearch Institute (MBARI), this project is an expansion of the Free Ocean Carbon Emission (FOCE) project. This iteration created a communications protocol between the different modules in an expandable array of PIC24-based boards.

Independent Moisture-Sensitive Automatic Watering System, Jessica Sherbon

Electrical Engineering

With the availability of home improvement supplies, plant owners can quickly and easily set up an automatic system that waters their gardens based on a specified schedule. However, most of these systems require an electric outlet or water faucet making them unusable in locations where installed water and power lines do not exist, such as apartment balconies. This project defines a small-scale automated watering system that runs independently of installed water and power lines. The system takes water from a reservoir, such as a tank or bucket, and supplies that water to individual plants via a drip system. The design …

Inductive Metal Identification, Paul Maggi

Electrical Engineering

This project focuses on creating a device to differentiate between various types of metals via magnetic induction. Magnetic induction is used because it is both non-optical and non-contact. It achieves this by generating a varying magnetic field, which induces eddy currents in the metal. These eddy currents produce small disturbances in the surrounding magnetic field, which can be sensed with Hall Effect Sensors (HES). The primary challenge in this project was generating a sufficiently strong magnetic field to detectable disturbances. In order to achieve better results, a stronger magnetic field must be used as well as more sensitive Hall Effect …

Gamecube To Nintendo 64 Controller Converter, Andrew Jia-Haur Lee

Electrical Engineering

No abstract provided.

Solar Powered Led Lantern For Developing Countries, Lacy Billingsly Iii

Electrical Engineering

In recent years, both LED and solar technology have become the focus of sustainable energy. LED lighting uses significantly less power than its fluorescent competitor. Solar cells enable clean, natural, and portable power. As these two entities become more efficient at exponential rates, the hope for the wide use of off-grid lighting in less developed countries seemingly increases at the same rate. Currently, there has been a development of industry for portable solar powered lighting systems. Before designing a product, a study was conducted of current products on the market that aim to light dark homes. This study and design …

Barrel Racer's Calculator, Hollie Kucera

Electrical Engineering

Barrel racing is a rodeo event in which a horse and rider attempt to complete a clover-leaf pattern around preset barrels in the fastest time. This sport combines the horsemanship skills of a rider and the horse’s athletic ability to safely and successfully maneuver around the three barrels (three fifty-five gallon metal drums) placed in an arena.

In barrel racing, the purpose is to make the run as fast as possible. An electric eye and timing system keep track of the time. The time starts when the horse and rider cross in between the electric eyes and ends when the …

Ignitron Trigger Circuit, John F. O'Hara Iii

Electrical Engineering

No abstract provided.