Engineering Commons^™

Three-Dimensional Structural Electronic Integration For Small Satellite Fabrication, Cassie Gutierrez

Open Access Theses & Dissertations

The ability to realize truly three-dimensional electronic circuits is complicated if not impossible using traditional fabrication techniques. Such techniques are limited to the use of two dimensional printed circuit boards (PCBs), and require various dissonant processes which exhaust time, volume and cost. Due to the nature of Additive Manufacturing (AM) such problems are diminished and in some ways completely overcome. Additive Manufacturing allows for a higher range of design freedom along conformal surfaces, as well as unit level customization; it is the threshold for embedded electronics, allowing for three-dimensional circuitry in ways traditional fabrication is unfeasible. In such ways, additive …

Nanoprobe I-V Characterization Of Cdte/Cds Micro And Nano-Patterned Solar Cells, Heber Prieto

Open Access Theses & Dissertations

This thesis presents a novel way to characterize micro and nano patterned cadmium telluride thin film solar cells via a nano-probe system. A historical review of CdTe-based solar cells is presented first followed by review of the technology developed to produce the patterned CdTe cells. A detailed presentation is then provided on the use of a Zyvex nanoprobing system to characterize the patterned solar cells. The I-V response of micro- and nano-patterned solar cells stimulated under different e-beam conditions is presented and analyzed. Suggestions of how to improve the technique are provided. This work documents, for the first time, the …

Control Of A Robotic Prototype Multi-Axis Synergistic System, Julio A. Torres

Open Access Theses & Dissertations

Balance is an ability that every person has and uses in normal daily life, to walk, run, stand, dance, etc. However, there are people who suffer a kind of balance impairment. The Computerized Dynamic Posturography (CDP) is technique in balance rehabilitation, where the patient is asked to stand on a moving platform that is equipped with sensors that measure how well you maintain your balance. In this thesis, a new CDP mechatronic system, the Multi-Axis Synergistic System (MASS), for balance assessment is being developed.

As a first stage and as the objective of this research work the transferable control algorithm …

Magnetic Cell Separation By Inkjet Printing For Disease Monitoring, Sylvia Lucia Natividad

Open Access Theses & Dissertations

The standard analysis technique for cell sorting, flow cytometry, requires centralized facilities such as tertiary Medical Centers. According to the U.S. Department of Health and Human Services Designated Health Professional Shortage Areas (HPSA) Statistics, in this country alone, more than 35 million people live in medically underserved areas, many of which need access to diagnostic procedures for proper management of their diseases. A cell sorting technique that can be done in low-resource settings at a decreased cost to the medical organization and the patient has been developed through this research project. By combining inkjet printing technology and magnetic labeling of …

Multi-Physics Modeling Of Induction-Based Additive Manufacturing Of Metals, Danny W. Muse

Open Access Theses & Dissertations

The shift towards 3D printing of functional products has provided a glimpse of the future in terms of manufacturing technologies and the creation of volumetrically complex structures made possible only through these technologies. 3D printing has emerged from the culmination of several technologies covering multiple industries and a myriad of materials. Unlike subtractive technologies such as mills, lathes and CNC machines, where material is removed from a bulk slab or billet to produce a desired part, 3D printing uses an additive layered approach to deposit material based on cross sections of the desired part. Both approaches produce parts based on …

Investigation Of The Divcon Neuron To Increase The Performance Of A Traditional Feed Forward Multi-Layer Perceptron And Its Hardware Implementation, Jovan Saenz

Open Access Theses & Dissertations

ABSTRACT

Artificial Neural Networks (ANNs) have been developed in an attempt to emulate the information processing capabilities of the biological brain. They offer an alternate computing approach to problems in which mathematical modeling is complicated, such as pattern recognition and pattern classification.

Since ANNs were proposed in the early 1940s, there has been a great amount of research effort dedicated to the development of new models that improve performance. Consequently, different architectures, a variety of activation functions, and distinct learning algorithms have been developed and implemented in different disciplines such as medicine, engineering, and science. In addition, ANNs have been …

Determination Of The Dynamic Behavior Of Subjects With Diabetic Neuropathy, Luis G. Sagarnaga Lopez

Open Access Theses & Dissertations

The diabetic foot is one of the most feared complications of diabetes [3]. Causes of a diabetic foot come from many disorders including diabetic neuropathy, peripheral vascular disease, charcot's neuropathy, foot ulceration, and limb amputation [4]. Statistics have revealed that 8.3 percent of population in the U.S. is affected by diabetes in 2010, i.e., 25.8 million people. About 60 percent to 70 percent of people with diabetes have mild to severe forms of nervous system damage [13]. There is an enormous impact on the physical and mental health of patients who suffer from diabetes.

This research was to determine the …

Raman And Infrared Study Of Electrospun Plla/Pcl Nanofiber Blends For Use In Tissue Engineering, Jose Luis Enriquez Carrejo

Open Access Theses & Dissertations

Recently, the biomedical engineering field has developed at a very fast pace as improved techniques and materials become available to promote its growth. Consequently, the research in polymeric biomaterials has been highly stimulated by this trend. The goal of the current research is to demonstrate the usefulness of the Raman scattering, Raman mapping, and infrared absorption spectroscopies to tissue engineering, by spectroscopically characterizing blends of PLLA and PCL polymers, which were prepared by electrospinning with and without cell addition. The proposed use of these blends is as primary biomaterials in biodegradable scaffolds used in tissue engineering. Both Raman and infrared …

Numerical Modeling Of Cds/Znxcd1-Xte Solar Cell, Farhana Anwar

Open Access Theses & Dissertations

Device modeling and simulation studies of CdS/ZnxCd1-xTe thin film solar cell have been carried out. A variety of graded band gap structures are examined. Incorporation of back electron reflector layer to improve open circuit voltage and carrier collection of CdTe solar cell was investigated. Device physics and performance determining parameters for different band gap profiles were analyzed. Based on simulation results, an optimal graded band gap structure for CdS/ZnxCd1-xTe solar cell is proposed. Performance of optimally graded band gap cell is superior to that of uniform bandgap cell.

Video Mosaicing Using Inertial Sensors, Arturo Maya Pereyra

Open Access Theses & Dissertations

A method to reduce the process complexity of Video Mosaicing could rely on information concerning the orientation of the camera instead of image feature tracking. Inertial sensors (e.g. accelerometers and gyros) could form part of a low cost motion based technology which can be used in this case and this thesis details an approach for Video Mosaicing based on such technology that requires non-computationally intensive algorithms.

The Application Of Fuzzy Granular Computing For The Analysis Of Human Dynamic Behavior In 3d Space, Murad Mohammad Alaqtash

Open Access Theses & Dissertations

Human dynamic behavior in space is very complex in that it involves many physical, perceptual and motor aspects. It is tied together at a sensory level by linkages between vestibular, visual and somatosensory information that develop through experience of inertial and gravitational reaction forces. Coordinated movement emerges from the interplay among descending output from the central nervous system, sensory input from the body and environment, muscle dynamics, and the emergent dynamics of the whole neuromusculoskeletal system.

There have been many attempts to directly capture the activities of the neuronal system in human locomotion without the ability to clarify how the …

Sparse Signal, Image Recovery In Compressive Sensing Technique Through L1 Norm Minimization, Phanendra Koppisetti

Open Access Theses & Dissertations

The classical Shannon Nyquist theorem tells us that, the number of samples required for a signal to reconstruct must be at least twice the bandwidth of the highest frequency for the signal of interest. In fact, this principle is used in all signal processing applications. Unfortunately, in most of the practical cases we end up with far too many samples. In such cases a new sampling method has been developed called Compressive Sensing (CS) or Compressive Sampling, where one can reconstruct certain signals and images from far fewer samples or measurements when compared to that of samples in classical theorem. …

Surface And Guided Waves On Structured Surfaces, Javier Polanco

Open Access Theses & Dissertations

Surface and guided waves on structured surfaces and inhomogeneous media studies the propagation of waves in systems with spatially varying parameters. In the rainbow case (chapter 1), the dielectric constant changes with coordinates. In the cylinder case: boundary and the metal (chapter 2), it is a curved surface. Finally, in the last case (chapter 3), the dielectric constant changes in z-direction.

A Novel Method For The Curing Of Metal Particle Loaded Conductive Inks And Pastes, David Adrian Roberson

Open Access Theses & Dissertations

The emerging technology of printed microelectronics involving the use of conductive inks in conjunction with standard printing techniques offers a fast and low waste method for creating microelectronics compared with standard manufacturing processes. A clear path to the creation of flexible electronics is present due to the ease of printing on flexible substrates. Moreover, creation of novel 3D structural electronics is possible via the integration of printing technologies and additive manufacturing (AM) techniques.

A key obstacle to the manufacturing of flexible and structural electronics comes from the temperature restrictions imposed by the substrates, which are typically polymeric. This hindrance has …