Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 4 of 4
Full-Text Articles in Engineering
Effect Of Arc Plasma Sintering On The Structural And Microstructural Properties Of Fe-Cr-Ni Austenitic Stainless Steels, Parikin Parikin, M. Dani, A. Dimyati, N. D. Purnamasari, B. Sugeng, M. Panitra, A. Insani, T. H. Priyanto, S. Mustofa, Syahbuddin Syahbuddin, A. Huang
Effect Of Arc Plasma Sintering On The Structural And Microstructural Properties Of Fe-Cr-Ni Austenitic Stainless Steels, Parikin Parikin, M. Dani, A. Dimyati, N. D. Purnamasari, B. Sugeng, M. Panitra, A. Insani, T. H. Priyanto, S. Mustofa, Syahbuddin Syahbuddin, A. Huang
Makara Journal of Technology
X-ray diffraction techniques were performed to determine the actual crystal structure of A2 austenitic stainless steel (ASS) as-cast and A2 ASS after arc plasma sintering (APS) for 2 s. Computations were conducted on the basis of the Bragg arithmetic formula by comparing the S2 arithmetic with the interplanar spacing. The Bragg arithmetic formula is a simple series for the determination of the crystalline phase of materials based on the Miller indices of cubic shapes or other shapes. A2 ASS as-cast was identified to have a crystal structure of face-centered cubic with lattice parameter a = 3.58 Å. A similar crystal …
Neutron Diffraction Study Of Multiferroic 0.6nife2o4/0.4batio3 Composite, Engkir Sukirman, Yosef Sarwanto, Syahfandi Ahda, Andon Insani
Neutron Diffraction Study Of Multiferroic 0.6nife2o4/0.4batio3 Composite, Engkir Sukirman, Yosef Sarwanto, Syahfandi Ahda, Andon Insani
Makara Journal of Technology
Neutron diffraction study on the 0.6NiFe2O4/0.4BaTiO3 multiferroic composite has been carried out. The 0.6NiFe2O4/0.4BaTiO3 multiferroic composites have been synthesized by solid reaction method. In this study, 20 g of BaTiO3 (BTO) and 20 g of NiFe2O4 (NFO) compounds were prepared from the powder raw materials of BaO3 and TiO2 for BTO, and NiO and Fe2O3 for NFO. Furthermore, both BTO and NFO were each crushed for 5 hours using High Energy Milling (HEM). Then the BTO and NFO were calcined in the furnace at 950 °C/5 hours and 900 °C/5 hours, respectively. Both NFO and BTO precursors were manually mixed …
Effects Of The Preheating Temperature On The Crystal Structure And Texture Of Martensitic Stainless Steel, Tri Hardi Priyanto, Rifai Muslih, Herry Mugirahardjo, Bharoto Bharoto, Andon Insani, Muzzakiy Muzzakiy
Effects Of The Preheating Temperature On The Crystal Structure And Texture Of Martensitic Stainless Steel, Tri Hardi Priyanto, Rifai Muslih, Herry Mugirahardjo, Bharoto Bharoto, Andon Insani, Muzzakiy Muzzakiy
Makara Journal of Technology
Theoretically, the preheating temperature refers to the start martensite temperature (Ms), and the martensite transformation can be considered as the conservation of the invariant habit-plane in the lattice structure. The habit-plane is the interface plane between austenite and martensite as measured on a macroscopic scale. From the calculation, Ms = 252 °C. The martensite formation can be affected by temperature or stress treatment. In this experiment, temperature treatment was conducted. The sample was treated at 250 °C ± 10 °C. Before and after the pre-heat treatment, the sample was characterized using the neutron diffraction method. BATAN’s Texture Diffractometer (DN2) with …
Texture Analysis Using The Neutron Diffraction Method On The Non Standardized Austenitic Steel Process By Machining,Annealing, And Rolling, Tri Hardi Priyanto, Parikin Parikin, Meijuan Li
Texture Analysis Using The Neutron Diffraction Method On The Non Standardized Austenitic Steel Process By Machining,Annealing, And Rolling, Tri Hardi Priyanto, Parikin Parikin, Meijuan Li
Makara Journal of Technology
Austenitic steel is one type of stainless steel which is widely used in the industry. Many studies on austenitic stainless steel have been performed to determine the physical properties using various types of equipment and methods. In this study, the neutron diffraction method is used to characterize the materials which have been made from minerals extracted from the mines in Indonesia. The materials consist of a granular ferro-scrap, nickel, ferro-chrome, ferro-manganese, and ferro-silicon added with a little titanium. Characterization of the materials was carried out in three processes, namely: machining, annealing, and rolling. Experimental results obtained from the machining process …