Engineering Commons^™

Identification Of Bridges With Fracture-Prone Details, Theodore Hopwood Ii, Rick Younce, Sudhir Palle

Kentucky Transportation Center Research Report

Welded steel girder bridges can contain details that can high welding and service stresses and are termed constraintinduced fractures (CIF). The Kentucky Transportation Cabinet has steel bridges with weld details known to cause CIFs whose girders have experienced fracture events. The Cabinet’s bridge inventory was reviewed and additional candidate bridges with potential CIF details were identified. A review of bridge plans and pictures along with followup field investigations pinpointed bridges with CIF details that warrant up-close (i.e., arm’s length) inspections. Several uninspected bridges were identified as candidates for inspection to determine if they contain CIF details. Guidance is provided to …

Experimental Calibration Of Centrally Loaded Built-Up Battened Compression Members, Ghada El-Mahdy Ph.D., P.Eng.

Civil Engineering

There is a large diversity in the requirements for designing built-up compression members between international design codes. Most codes, including the North American standards and specifications specify the use of an equivalent or modified slenderness ratio. In general, all North American standards and specifications agree on the need of using a modified slenderness ratio, but differ in the factor used to multiply the local slenderness ratio. Theoretically it is difficult to estimate the exact value of this factor, and using experimental methods does not capture the exact value of this factor either. Hence, a different approach is needed to determine …

Steel Test Set-Up For Non-Ductile Concrete Shear Walls, Colin S. Ridgley

Architectural Engineering

The purpose of this project was to provide a robust test set-up for the thesis work being conducted by graduate students, Jerry Luong & Rory de Sevilla. Their research aims to evaluate the feasibility of using fiber-reinforced polymer wraps and splay anchors to retrofit non-ductile concrete shear walls through a series of tests on reinforced concrete walls.

Four key constraints governed the design of the test set-up. First, the wall can be cyclically, laterally loaded to develop data for comparison with theoretical analysis methods. Second, the wall can be axially loaded to simulate interaction effects and prevent a sliding failure …

Development Of A Mechanical Device For Measuring Connection Rotations During Seismic Loading, Garrett Tatum

Civil Engineering Undergraduate Honors Theses

This engineering design project sought to design a cheap and easy-to-use sensor to monitor seismic connection rotations in steel buildings during earthquakes by using a linear ratchet mechanism. The idea for the project goes against the mainstream of research that is seeking to develop complex digital networks for monitoring structures in earthquake regions. Whereas many modern sensor networks require high-cost, professionally maintained digital networks, an analog sensor could provide much of the same information at a fraction of the cost, allowing sensors to be more widely utilized, particularly in developing countries. This project required an iterative engineering design process to …

2019 Student Steel Bridge Team, Kourtney Arena, Andrew Biglin, Brett Palmer, Nathaniel Maute, Kenneth Reiser, Jacob Dicks, Paul Kowaleski

STEM Student Research Symposium Posters

Every year AISC runs a regional and national steel bridge competition. The competition offers a chance for civil engineering students to gain valuable experience designing a bridge. In addition to this, mechanical engineering students are provided the opportunity to practice machining steel parts. For the competition, teams from participating schools are given a scenario with certain constraints to design a bridge for. At the competition, the bridges are ranked based on weight, structural efficiency, construction economy, assembly speed, deflection, aesthetics, and overall performance.

The program Risa 3D was used in order to design and perform analysis on the bridge. Using …

Adhesion Of Bituminous And Cementitious Materials Using Particle-Probe Scanning Force Microscopy, Yujie Li

Graduate College Dissertations and Theses

As the most important materials in civil engineering, bituminous and cementitious materials have been used widely in pavements and constructions for many years. Accurate determination of adhesion is important to the bonding properties of bituminous and cementitious materials. In this work, we presented a novel approach to measure the adhesion between binders and aggregate mineral particles at microscopic scale.

Particle probe scanning force microscopes (SFM) were used to study the adhesion between mineral microspheres representing the primary aggregate constituents (Al2O3, SiO2 and CaCO3) and various control (PG 64-22 and PG 58-22) and modified binders. Results showed that these modified SFM …