Engineering Commons^™

Comparing Sandwich Wall Panel Shear Connector Testing Methodologies, Parker S. Syndergaard

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Precast concrete sandwich wall panels (PCSWPs) have been used in the precast industry for decades due to their durability, rapid construction, and thermal efficiency. Shear connectors are used to connect the two wythes of concrete to allow composite action of the system. In order to design concrete sandwich panel systems to act compositely, the engineer must obtain design values from a connector manufacturer, often times making engineers uncomfortable. Shear connectors are typically proprietary, and are required to first have design values validated through destructive testing. The method in which connectors are validated often times varies by each company. This project …

Shrinkage Cracking In Concrete Tilt-Up Construction, Stewart Hooks, Jack Robinson

Architectural Engineering

The purpose of this project is to investigate a particular, undesirable cracking pattern in concrete tilt-up panels that, until now, did not have a known definite cause. The cause of this cracking pattern is hypothesized to be due to shrinkage restraint of the concrete panels. The cracking under investigation occurs at the bottom corners of the Tilt-Up panels, suggesting that the base of the panel is restrained from shrinkage. This project models various components of Tilt-Up Construction that have potential for restraining the panels from shrinking. This project consists of the following main components.

The first aspect of this project …

Pvc Stay-In-Place Panel Covers For Tilt-Up And Pre-Cast Construction, Purdue Ect Team

ECT Fact Sheets

Octaform™ stay-in-place concrete forming system is PVC insulated concrete form system. These forms have been used in the industry for various applications to improve the insulation and corrosion resistance of structures. Octaform™ has developed the panel covers so the advantages of PVC stay-in-place concrete forming systems could be applied to tilt-up and pre-cast construction.

Performance Of Transverse Post-Tensioned Joints Subjected To Negative Bending And Shear Stresses On Full Scale, Full Depth, Precast Concrete Bridge Deck System, Kayde Steven Roberts

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Accelerated bridge construction has quickly become the preferred method for the Utah Department of Transportation (UDOT) as well as many other DOT’s across the United States. This type of construction requires the use of full depth precast panels for the construction of the bridge deck. The segmented deck panels produce transverse joints between panels and have come to be known as the weakest portion of the deck. Cracking often occurs at these joints and is reflected through the deck overlay where water accesses and begins corrosion of the reinforcement and superstructure below. For this reason post-tensioning of the deck panels …

Gfrc Facade Panels With Steel Stud/Flex Anchor Connection, Purdue Ect Team

ECT Fact Sheets

The ability of building cladding systems to perform successfully depends primarily on their proper design and construction. Current practices in the United States utilize GFRC (Glass Fiber Reinforced Concrete) panels. However, new problems are being detected with such systems. The facade and its attachments (using GFRC) are not being adequately implemented to accommodate vertical and horizontal differential movement between the panels and concrete frame which is resulting in failure or cracking of the panels, and chipping off of the supporting concrete. With proper design and construction, steel stud-framed GFRC-skin cladding concept provides a versatile system for freedom of expression in …

Ultrascreen - Sight And Sound Barrier Partition Walls, Purdue Ect Team

ECT Fact Sheets

Panels have been widely used for many years to act as sight and sound barriers in most of the highways and in residential areas where visual privacy is needed. The United States Gypsum Company, early in the 1980's started developing technologies to improve and reduced costs using lightweight cement panels. Recently, USG along with AFM Corporation introduced ULTRASCREEN: Sight and Sound Barrier. This lightweight panels require no special equipment for installation, maintenance, or replacement making them beneficial. This latest development also creates a system with good acoustical performance and excellent strength to weight ratio.

Robotized Spraying Of Grc Panels, Purdue Ect Team

ECT Fact Sheets

The manual manufacturing process of GRC panels consists of two or four consecutive stages, depending on the panel type. The robotized spraying process is controlled by three (3) main modules which are executed sequentially or in parallel, depending on the task. The first module utilizes a common CAD environment with access to information relating to the manufacturing tools and parameters and to the design rules for the product. The off-line module is divided into three different submodules: kinematic control, path planning and task planning.