Engineering Commons^™

Pilot-Scale Test Of Water Wash Carbon Dioxide Absorption System For Purifying Landfill Gas At Jones Island Wastewater Reclamation Facility, Rebecca Schruender

Theses and Dissertations

Biogas, a product of the digestion of organic material, consists primarily of methane and carbon dioxide. By purifying raw biogas, or removing the carbon dioxide, it can be upgraded to biomethane, which can be used to generate heat and electricity or as a substitute for natural gas. An effective method of biogas purification is the water wash process, which consists of an absorption column in which a stream of biogas runs counter-current to a stream of water. The carbon dioxide dissolves in the water, increasing the methane concentration of the gas. A pilot scale system was operated at Jones Island …

Dynamic Vehicular Trajectory Optimization For Bottleneck Mitigation And Safety Improvement, Wenqing Chen

Theses and Dissertations

Traffic bottleneck is defined as a disruption of traffic flow through a freeway or an arterial, which can be divided as two categories: stationary bottleneck and moving bottleneck. The stationary bottleneck is mainly formed by the lane drops in the multi-lane roadways, while the moving bottleneck are due to the very slowing moving vehicles which disrupt the traffic flow. Traffic bottlenecks not only impact the mobility, but also potentially cause safety issues.

Traditional strategies for eliminating bottlenecks mainly focus on expanding supply including road widening, green interval lengthening and optimization of intersection channelization. In addition, a few macroscopic methods are …

Underwater Particle Image Velocimetry (Piv) Measurement Of Turbulence Over Mussel Bed In A Deepsite Of Lake Michigan, Tong Jin

Theses and Dissertations

The influence of the benthic filter feeders, such as bivalves, on ecosystem plankton, and nutrient dynamics is considered significant in shallow marine and freshwater systems. Recent indirect evidence showed that the profundal quagga mussels (Dreissena rostriformis bugensis) have fundamentally altered energy flow and dynamics of nutrients and phytoplankton in Lake Michigan and other Great Lakes. To investigate the phytoplankton grazing rate of the quagga mussel and the mussel siphon currents induced bio-mixing, a self-contained in situ Underwater Particle Image Velocimetry was developed to measure the turbulence structure and the turbulent diffusion coefficient immediately above the profundal quagga mussel covered substrate …

Application Of Survival Analysis Techniques To Probabilistic Assessment Of Fatigue In Steel Bridges, Azam Nabizadehdarabi

Theses and Dissertations

The fatigue of engineering materials under repetitive loading is a significant issue affecting the design and durability of components and systems in a variety of engineering-related applications including civil, mechanical, aerospace, automotive, and electronics. Many factors can affect the service life of a component or system under repetitive loading, such as the type of structure, loading, connection details, stress state, peak stress or stress range, surface condition, temperature, and environmental exposure. Currently, there is no comprehensive probabilistic approach that can systematically address all the factors that contribute to fatigue on a single mathematical platform. However, advanced analysis techniques developed for …

Multi-Facet Retrofit Approach To Improve Energy Efficiency Of Existing Class Of Single-Family Residential Buildings In Florida, Kwame Baffour Ohene Amoah

Theses and Dissertations

There are many approaches to incorporate energy efficiency measures (EEMs) into building through retrofit projects. Single-family buildings are an essential target for energy improvements because of their energy-saving potential and considerable market share. This study evaluates energy savings and cost-effectiveness of individual retrofit options. It proposes energy efficiency measures for an existing class of single-family homes constructed between the years of 1950 and 1970. The study uses a baseline building located in Melbourne, FL, as a case study. A survey via clustering data mining was conducted on Florida Single-Family Residential (SFR) buildings (1950 – 1970) to establish patterns of construction, …

Experimental Investigation Of Hydraulic Effects On Unsaturated Soils Behaviors, Muwafaq Awad

Theses and Dissertations

Geo-structures are frequently constructed in or on soils with unsaturated conditions and are subjected to variations of moisture contents due to seasonal changes. Even though unsaturated soil mechanics have been established for several decades, it has not been fully implemented in practice today because of a lack of understanding of the interaction between the soil, water, and air phases. Many experimental research studies have been conducted to improve the understanding of unsaturated behavior but these studies are typically limited to small soil elements tested under fully drained conditions. The goal of this research is to evaluate the effect of hydraulics …

A Non-Contacting System For Rail Neutral Temperature And Stress Measurements, Katelyn Knopf

Theses and Dissertations

Continuous Welded Rail (CWR) has become the standard in modern railway track construction around the world because it alleviates well-documented disadvantages of rail joints in a track. CWR practice results in long segments of continuous rail in the track that will develop significant thermal elongation. To avoid the use of impractical large thermal expansion joints and limit the expected thermal elongation, the rail is anchored to the ties. Consequently, the rail is exposed to higher thermal stress demands as the rail temperature varies. At the time a CWR is laid, the rail is free of thermal stresses; the temperature at …

Prototyping Elliptically Profiled Inverted Pendulum Walls In Cross-Laminated Timber (Clt) For Passive Self-Centering And Seismic Resiliency, Marco Lo Ricco

Theses and Dissertations

Cross-laminated timber (CLT) buildings garnered international attention, nearly a decade ago, for elevating wood construction to new heights on fully panelized assemblies of floors and walls. While highly regarded as a sustainable building material, use of CLT as a structural wall system depends on seismically resilient strategies like controlled rocking. This project prototyped elliptically profiled CLT panels and slotted-pin steel connections, at full-scale, to produce rolling and slip-friction inverted pendulum wall systems of one-story height and inspired by seismic isolation concepts. Digital fabrication realized elliptical profiles along the load-bearing edges of six 5-ply CLT panels and various customized slot shapes …

Energy Dissipating Connector For Precast Shear Walls In High-Seismic Areas, Mohammed Aljuboori

Theses and Dissertations

ABSTRACT

ENERGY DISSIPATING CONNECTOR FOR PRECAST SHEAR WALLS IN HIGH-SEISMIC AREAS

By

Mohammed Aljuboori

The University of Wisconsin – Milwaukee, 2019

Under the Supervision of Dr. Habib Tabatabai

Precast concrete systems are widely used in a variety of structures such as parking garages, residential units, shopping centers, and transportation stations. In some cases, precast structures are preferred over conventional cast-in-place (CIP) concrete conventional structures because of ease of construction, rapid implementation, and lower levels of energy consumption. One area where precast systems have traditionally been at a disadvantage is high seismic applications. In seismic regions, precast concrete structures must have …

Study Of The Long-Term Shaft Resistance Of Energy Piles In Saturated Clays, Saeed Yazdani Kachooie

Theses and Dissertations

This research aims to qualitatively/quantitively assess the effect of temperature variation on the energy pile shaft resistance. The important mechanisms by which heating can change the shear strength of clay and clay-concrete interface are evaluated using experimental and numerical methods. As for experimental method, temperature-controlled triaxial tests, constant normal load (CNL) direct shear tests and small-scale pile tests were conducted. As for numerical approach, a fully coupled thermo-hydro-mechanical (THM) analysis was performed to simulate the experimental test results so that the capability of such analysis to predict thermo-mechanical behavior of energy piles is evaluated. Reconstituted (HC-77) kaolin clay, one-dimensionally consolidated …

Construction Of Bismuth Oxyhallide-Based Heterojunction-Structured Composite And Its Environmental Application For Water Treatment, Li Wang

Theses and Dissertations

With the rapid development of the global economy, environmental protection and sustainable development have become the main trends of current society. In particular, water pollution and energy shortage are outstanding issues that need to be solved in a clean and sustainable way. Recently, semiconductor-based photocatalytic technology, an environmentally friendly technique, has attracted enormous attention and become an emerging research hotspot in the application of water/wastewater treatment and generation of renewable energy as it can convert infinite solar energy into chemical energy. Conventional semiconductor materials usually have a relatively large band gap that only responds to the ultraviolet light, which largely …

Modeling To Predict The Salt Transport Between A Scale Model Estuary And The Unconfined Aquifer With Groundwater Flow, Abeer Ibraheem Khazaly

Theses and Dissertations

In many field studies, variation in fluid density may have important effects on controlling groundwater flow and solute transport processes. These studies include: Indian River Lagoon (IRL), a coastal estuary, located on the east coast of Florida, saline disposal basins, radioactive waste disposal and contaminant spills. In the environment, where the fresh groundwater region is in direct contact with the saline seawater region in coastal aquifers, dynamic equilibrium normally exists between these two regions, but there are numerous human and environmental factors that can adversely impact the equilibrium and lead to severe saltwater contamination of the freshwater region. Intrusion of …

Damping In Transient Pressurized Flows, Sahad Salim Elyass Khilqa

Theses and Dissertations

Piping systems are commonly designed to withstand the first transient pressure peak, which is unaffected by dissipation. However, for multiple operations of control equipment, e.g., pump start-up following pump shutdown, load acceptance following load rejection on hydraulic turbines, etc., an accurate prediction of the dissipation of pressure oscillations is needed to determine a suitable time for the second operation. For this purpose, a method is presented to compute the dissipation of pressure oscillations in piping system following a simple procedure used for computing the dissipation of vibrations of bridges and other structures. Similar to structural engineering, this method is simple …

The Study Of Flow Hydrodynamics And Transport Processes Over Mixed Bedrock-Alluvial Reaches, Mohammad Sadegh Jafarinik

Theses and Dissertations

Research efforts on mixed bedrock-alluvial rivers primary focused on the bedrock incision and very few studies investigated the alluvial morphodynamics of such systems. To the best of my knowledge none of these models have been considered the spatial variability of the sediment grain size of the bed surface in mixed bedrock-alluvial reaches and very few models focused on the spatial changes in alluvial cover within these reaches. Furthermore, a perusal of the literature on mixed bedrock-alluvial river morphodynamics reveals that very little information is available on 1) bedform geometry and flow resistances and 2) sediment sorting patterns in presence of …

Health Monitoring Of Liquid Pipelines, Mohammed Hameed Sabhan Al-Tofan

Theses and Dissertations

The crude and refined oil, water, and other liquids are widely transported through pipelines over long distances within geographical boundaries of countries or beyond. Pipeline accidents, however, are frequent, affecting operation and reducing targeted performance. The frequency of these accidents presents a growing concern and necessitates the need for an effective health monitoring plan. This plan requires monitoring of flow conditions and warning of any changes or abnormal conditions. Abnormalities in the flow conditions include changes in the piping system performance due to defects, such as leaks and blockages. These changes can be located and quantified utilizing different approaches. Two …

Modeling Particle Dispersal In Bedload Dominated Settings, Sanaz Borhani

Theses and Dissertations

Tracer particles are used to study bedload transport in gravel bed rivers. One of the advantages associated with their use is that they allow for direct measurements of particle entrainment rates in bedload transport and particle displacement. The main issue in field studies with tracer particles is the difference between tracer short term and long term behavior. This difference is due to the fact that particles undergo vertical mixing or move to less active locations such as bars or even floodplains. For these reasons the mean tracer velocity decreases over time. This phenomenon has been called tracer slowdown and it …

Damage Evaluation Of Concrete Structures Using Acoustic Emission, Rafal Anay

Theses and Dissertations

The deterioration and aging of the infrastructure in the U.S. have become a crucial issue, especially for highway bridges and nuclear power plants. The reliability and safety of existing structures are affected by growing populations and limited resources. This issue has gained significant concern during the last two decades and efforts are being conducted to accelerate the improvement of nondestructive testing (NDT) and structural health monitoring (SHM) methods. Additional information regarding the condition of existing structures and the early detection of damage can aid in reducing overall maintenance costs. The studies presented in this dissertation employ acoustic emission (AE) as …

Structural Health Monitoring Of Laminate Structures Using Shear-Mode Piezoelectric Sensors, Hussain Altammar

Theses and Dissertations

Structural health monitoring (SHM) employing embedded piezoelectric transducers has shown potential as a promising solution for inspection of different engineering structures such as aircraft, bridges, and renewable energy structures. Despite advancements in the field of ultrasonic SHM, inspection of laminate structures is still a major challenge due to their susceptibility to various joint defects. This thesis presents a novel approach to tackle the challenge of inspecting laminate structures using shear-mode (d35) piezoelectric transducers that are made of lead zirconate titanate (PZT).

This study begins with the characterization of d35 piezoelectric transducers using analytical, numerical, and experimental approaches. The results were …

Modeling Of Hurricane-Induced Interior And Contents Damage And Associated Time-Related Expenses To Residential Buildings, Roberto Vicente Silva De Abreu

Theses and Dissertations

Hurricanes are a main cause of economic losses in many parts of the world, including the state of Florida. They affect the exterior, interior, and the contents of residential buildings. The damage of the interior can be as much as half of the total damage, but the estimation of the interior damage is still somewhat crude. Most damage models estimate interior damage as a percentage of the exterior damage, or through simple relationships, that relate the height of water ingress in the building to the interior damage. The current version of the Commercial Low-Rise Residential vulnerability model (CLR) of the …

Multi-Segment Pile-Supported Bridge Approach Slabs For Control Of Differential Settlement, Ahmed Bahumdain

Theses and Dissertations

The roughness of the transition between the bridge and the roadway is a well-known issue that affects roughly 25% of the bridges in the United States. As soil underneath the approach slab settles, deferential settlement develops between the bridge and the approaching roadway. This may negatively affect the ride quality for travelers and result in substantial long-term maintenance costs. Because of the differential settlement, bumps could develop at the ends of the bridge when abrupt changes in slope (exceeding 1/125) occurs.

This study was aimed at mitigating the formation of bumps at the ends of the bridge through a new …

A Comprehensive Study On The Estimation Of Freeway Travel Time Index And The Effect Of Traffic Data Quality, Ambily Pankaj

Theses and Dissertations

Travel time reliability aims to quantify the variation of travel time by using the entire range of travel times for a given trip, for a selected time period over a selected horizon. A trip can occur over a segment, facility or any subset of the transportation network, for the purpose of calculating travel time reliability. As one of the most important performance measures, travel time reliability reports the number of trips that fail or succeed according to a predetermined standard. Unreliability is usually caused by the interaction of factors that influence travel times, such as fluctuations in demand due to …

The Effective Use Of Portland Cement In Reactive Powder Hybrid Asphalt Concrete, Clayton Cloutier

Theses and Dissertations

Today, building a durable and cost-efficient infrastructure while minimizing future repair needs is a challenging task, and innovative technological breakthroughs are needed. Limited research has been conducted to investigate the use of portland cement (PC) to improve the performance of asphalt pavements. Portland cement in bitumen materials is attractive as it can improve the performance and reduce costs. Warm Mix Asphalt (WMA) is also an attractive alternative to Hot Mix Asphalt (HMA) as this material produces tremendous energy savings by lowering the production temperatures and enhances certain performance characteristics. It can be envisioned that the use of portland cement incorporated …

A Comprehensive Study On The Estimation Of Freeway Travel Time Index And The Effect Of Traffic Data Quality, Ambily Pankaj

Theses and Dissertations

Travel time reliability aims to quantify the variation of travel time by using the entire range of travel times for a given trip, for a selected time period over a selected horizon. A trip can occur over a segment, facility or any subset of the transportation network, for the purpose of calculating travel time reliability. As one of the most important performance measures, travel time reliability reports the number of trips that fail or succeed according to a predetermined standard. Unreliability is usually caused by the interaction of factors that influence travel times, such as fluctuations in demand due to …

Analysis Of Frp-Wrapped Concrete Piles In Integral Abutment Bridges Subjected To Axial And Cyclic Lateral Loads, Hassan Mohammed Magbool

Theses and Dissertations

ABSTRACT

The long-term maintenance problems associated with expansion joints, which are used to accommodate bridge movements in conventional bridges, have been the primary motivation for the use of integral abutment (jointless) bridges. These bridges rely on the interaction between the structure and the surrounding soil to accommodate bridge movements without the use of any expansion joints on the bridge superstructure. As the bridge superstructure expands and contracts due to seasonal thermal and other strains, relatively large forces can develop in the pile near the pile-cap interface. These reversible moment and shear forces can lead to localized damage near the top …

Identifying And Incorporating Driver Behavior Variables Into Crash Prediction Models, Mohammad Razaur Rahman Shaon

Theses and Dissertations

All travelers are exposed to the risk for crashes on the road, as none of the roadways are entirely safe. Under Vision Zero, improving traffic safety on our nation’s highways is and will continue to be one of the most pivotal tasks on the national transportation agenda. For decades, researchers and transportation professionals have strived to identify causal relationships between crash occurrence and roadway geometry, and traffic-related variables on the mission of creating a safe environment for the traveling public. Although great achievements have been witnessed such as the publication of the Highway Safety Manual (HSM), research is rather limited …

Damping Coefficient Sensitivity Analysis Of High Rebound Soils In Florida, Aline Franqui

Theses and Dissertations

The dynamic response of soils is related to a damping factor, which represents the energy absorbed by the soil as the pile moves. Certain blends of fine sands, silts and clays are producing pile rebound during driving. For that reason, the objective of this thesis is to conduct a damping coefficient sensitivity analysis of high rebound soils in Florida. Forty cyclic triaxial tests from six sites in Central and Northern Florida were analyzed to evaluate damping. Two approaches were used, one based on the change in stress over time and a second based on the viscous energy absorbed per cycle. …

Design And Analysis Of Fiber Reinforced Concrete Structure For Transportation Infrastructures, Salam Adil Mutlag Wtaife

Theses and Dissertations

Concrete is one of the most popular materials in superstructures (buildings), substructures (foundation) and infrastructure facilities (bridges, pavements, and tunnels). However, concrete is a brittle material that cracks easily under tension. Fiber may be used as reinforcement to impede the concrete from cracking as well as to increase the concrete flexural strength. Nevertheless, current design codes do not include this design enhancement. Furthermore, there are discrepancies in the design methodology concerning the inclusion of discrete fibers in concrete structures. Therefore; there is a need to develop new analysis methodology and design methodology for fiber reinforced concrete (FRC) and fiber reinforced …

Lateral And Torsional Seismic Vibration Control For Torsionally Irregular Buildings, Osman Akyürek

Theses and Dissertations

During strong earthquakes or wind gusts, it is likely that buildings with torsional irregularity in the plan have an can be seriously damaged, partially collapsed or fully collapsed. This is because Torsionally Irregular Buildings (TIBs) may have significant aerodynamic torsion loads that increase the eccentricity between the center of mass and the center of rigidity, especially in dominant torsion modes. For this reason, torsion leads to excessive increase in lateral motions when dynamic loads excite the buildings. Torsional irregularity is one of the main failure causes during strong dynamic excitations due to earthquakes or wind gusts. Ignoring torsional irregularity in …

Taxonomy And Abstraction Of The On-Demand Mobility Aviation System For Smart Cities, Wancheng Dai

Theses and Dissertations

The on-demand mobility aviation system is a new paradigm providing aircraft-based point-to-point transportation services to travelers in urban and suburban areas. Many consider it as the next revolution in intelligent transportation systems. Since it does not require pre-scheduling and vehicles travel at high speed, travel times are dramatically decreased, which overcomes issues of the current ground transportation system, improves travel times and level of service, increases productivity and creates new business models. Likewise, it is envisioned to generate positive environmental outcomes. Since this is a new and unique mode of intelligent transportation, few is known about its potential success and …

Effect Of Industry Clusters And Commodity Flow Characteristics On The Selection Of Freight Transportation Modes In The United States With Advanced Econometric Approaches, Taleb Eissa Ali Eissa

Theses and Dissertations

Mode choice is an important strategic decision for shippers to carry commodities efficiently. Freight mode-choice is an important activity to develop a successful freight transportation business in the private sector and to plan for economically consistent freight transportation infrastructures in the public sector. Freight activities result from the complex interactions between different economic agents, but these relationships are commonly relaxed to account for three major agents: shippers, carriers and receivers. Furthermore, the behavior of freight choice is commonly not concentrated in one agent, but rather is divided jointly over multiple individuals and firms in a logistics process, each component of …