Engineering Commons^™

Investigation And Modification Of Single-Post Aluminum Sign Supports For Mash Crashworthiness, Rodrigo Quintero

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Traffic signs are used to display information to drivers and are one of the most commonly encountered roadside structures. Although they are a vital traffic control device, signs can pose a significant safety risk to errant drivers due to their extensive placement and proximity to the roadway. Therefore, traffic signs and their supports must be designed with crashworthiness in mind to reduce the likelihood of injury in the event of a vehicle impact. Prior to 2009, these systems were evaluated using the crash testing criteria found in the National Cooperative Highway Research Program (NCHRP) Report No. 350 [1]. Currently, they …

Development Of A Mash Test Level 4 Open Concrete Bridge Rail, Jacob Delone

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

An open concrete bridge rail was designed and developed according to safety performance guidelines in the American Association of State Highway Transportation Officials (AASHTO) Manual for Assessing Safety Hardware (MASH) for Test Level 4 (TL-4). Systems designed and developed under previous guidance were studied, and their geometric information and full-scale crash testing performance was studied to establish the geometry of the new bridge rail. Yield-Line Theory and the AASHTO Post and Beam design methods were studied, and a modified version of the AASHTO Post and Beam method was utilized to determine the capacity of the new open concrete bridge rail. …

Conceptual Development Of An Impact-Attenuation System For Intersecting Roadways, Joseph G. Putjenter

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Longitudinal barriers are commonly used to shield hazards, including stiff bridge rail ends and slopes. In some locations, a secondary roadway intersects the primary roadway within the guardrail’s length-of-need (LON). Some intersections have as little as 15 ft (4.6 m) between the intersection and beginning of the bridge railing, which require short-radius guardrail systems. No short-radius systems have been tested and approved to current impact safety standards for shielding hazards with these conditions.

Site conditions provided by the Nebraska Department of Roads were used to determine the constraints for a new safety treatment for intersecting roadways and include intersection radii, …

Development Of A Mash Tl-3 Transition Between Guardrail And Portable Concrete Barriers, David A. Gutierrez

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Often, road construction causes the need to create a work zone. In these scenarios, portable concrete barriers (PCBs) are typically installed to shield workers and equipment from errant vehicles as well as prevent motorists from striking other roadside hazards. For an existing W-beam guardrail system installed adjacent to the roadway and near the work zone, guardrail sections are removed in order to place the portable concrete barrier system. The focus of this research study was to develop a proper stiffness transition between W-beam guardrail and portable concrete barrier systems. This research effort was accomplished through development and refinement of design …

Cable Median Barrier Failure Analysis And Prevention, Dean L. Sicking, Cody S. Stolle

Mid-America Transportation Center: Final Reports and Technical Briefs

Cross-median crashes have been identified as one of the highest injury or fatality risk crash types. Although crossmedian crashes account for only 2% to 5% of all median crash events, they are disproportionately represented in the number and frequency of fatalities on interstate roadways. Many states have utilized cable median barriers to reduce the risk of cross-median crashes, frequently with great success. However, cable median barriers are also fixed obstacles to errant vehicles. Cable median barriers can place occupants at increased risk of severe injury or fatality if the barrier fails to adequately contain and redirect errant vehicles, resulting in …

Development Of Advanced Finite Element Material Models For Cable Barrier Wire Rope, John D. Reid, Karla A. Lechtenberg, Cody S. Stolle

Mid-America Transportation Center: Final Reports and Technical Briefs

An improved LS-DYNA model of ¾-in. (19-mm) diameter 3x7 wire rope commonly used in roadside cable guardrail installations has been developed. A Belytschko-Schwer beam element was selected along with material *MAT_166. Numerical noise was reduced using part stiffness damping with a coefficient of 2%, and frequency range damping with a coefficient of 12%. The optimum element length based on timestep, accuracy, and computational cost was determined to be between 0.4 and 0.8 in. (10-20 mm). Dynamic component tests were conducted on wire rope to determine material properties. These tests were simulated and the results compared to the physical tests. The …