Engineering Commons^™

Prioritization Of Research On Bridge Railings For Use On Timber Deck Bridges And Development Of Two Glulam Bridge Railing Systems, Jared Duren

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

In the past, many timber bridge railings, bridge railings for use on timber deck bridges, and approach guardrail transition systems to accompany these railings, have been developed to meet different impact safety criteria. Through an extensive literature review, the design details of these systems were identified and organized. A survey was then developed and distributed to multiple government agencies and timber industry members to identify their desire for these bridge railing and approach guardrail transition systems to be developed to meet current American Association of State Highway and Transportation Officials (AASHTO) Manual for Assessing Safety Hardware (MASH) impact safety criteria. …

Investigation Of A Tractor-Tank Trailer Roadside Containment Barrier, Dean L. Whitfield

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The objective of this research project was to develop a new, cost-effective, Manual for Assessing Safety Hardware (MASH) Test Level 6 (TL-6) barrier. A literature review on prior Test Level 5 and Test Level 6 barriers was conducted, and the cost of current TL-5 and TL-6 barriers was established. Existing and modified design procedures for roadside barrier were reviewed as well as current TL-6 design forces. A preliminary TL-6 truck model was developed in LS-DYNA. The minimum barrier height to contain a tractor-tank vehicle was determined to be 62 in. for a rigid, vertical-faced barrier through LS-DYNA computer simulation. New …

Conceptual Development Of An Impact-Attenuation System For Intersecting Roadways, Joseph G. Putjenter

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Longitudinal barriers are commonly used to shield hazards, including stiff bridge rail ends and slopes. In some locations, a secondary roadway intersects the primary roadway within the guardrail’s length-of-need (LON). Some intersections have as little as 15 ft (4.6 m) between the intersection and beginning of the bridge railing, which require short-radius guardrail systems. No short-radius systems have been tested and approved to current impact safety standards for shielding hazards with these conditions.

Site conditions provided by the Nebraska Department of Roads were used to determine the constraints for a new safety treatment for intersecting roadways and include intersection radii, …

Increased Span Length For The Mgs Long-Span Guardrail System, Nicholas A. Weiland

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Long-span guardrail systems have been recognized as an effective means of shielding low-fill culverts while minimizing construction efforts and limiting culvert damage and repair. The current MGS long-span design provided the capability to span unsupported lengths up to 25 ft (7.6 m) without the use of nested guardrail. The excellent performance of the MGS long-span system in full-scale crash tests suggested that longer span lengths may be possible with the current design.

A detailed analysis of the MGS long-span guardrail system was performed using the finite element software program LS-DYNA^®. It was shown that the MGS long-span design …

Development Of A Mash Tl-3 Transition Between Guardrail And Portable Concrete Barriers, David A. Gutierrez

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Often, road construction causes the need to create a work zone. In these scenarios, portable concrete barriers (PCBs) are typically installed to shield workers and equipment from errant vehicles as well as prevent motorists from striking other roadside hazards. For an existing W-beam guardrail system installed adjacent to the roadway and near the work zone, guardrail sections are removed in order to place the portable concrete barrier system. The focus of this research study was to develop a proper stiffness transition between W-beam guardrail and portable concrete barrier systems. This research effort was accomplished through development and refinement of design …

Safety Investigation And Guidance For Work-Zone Devices In Freight Transportation Systems Subjected To Passenger Car And Truck Impacts With New Crash Standards, Ronald K. Faller Ph.D., P.E., Dean L. Sicking Ph.D., P.E., Karla A. Lechtenberg M.S.C.E., E.I.T., James C. Holloway M.S.C.E., E.I.T., Jennifer D. Schmidt

Mid-America Transportation Center: Final Reports and Technical Briefs

Crashworthy, work-zone, portable sign support systems accepted under NCHRP Report No. 350 were analyzed to predict their safety peformance according to the TL-3 MASH evaluation criteria. An analysis was conducted to determine which hardware parameters of sign support systems would likely contribute to the safety performance with MASH. The acuracy of the method was evaluated through full-scale crash testing. Four full-scale crash tests were conducted with a pickup truck. Two tall-mounted, sign support systems with aluminum sign panels failed the MASH criteria due to windshield penetration. One low-mounted system with a vinyl, roll-up sign panel failed the MASH criteria due …