Engineering Commons^™

Enhancing Bridge Resilience And Overheight Vehicle Mitigation Through Innovative Sacrificial Cushion Systems, Aly Mousaad Aly, Marc Hoffmann

Faculty Publications

Transportation departments have made significant strides in addressing the challenges posed by the increasing weights of trucks on bridges. While there is a growing awareness of overheight vehicle collisions with bridges, implementing effective countermeasures remains limited. The susceptibility of bridges to damage from such collisions is on the rise, further exacerbated by unpredictable lateral impact forces. This study employs nonlinear impact analysis to assess the response of an unprotected vehicle-girder model, yielding realistic deformation outcomes comparable to observed impacts on the US-61 bridge. Predictions for a truck traveling at 112.65 km/h indicate deformations of 0.229 m, 0.161 m, and 0.271 …

Augmenting External Surface Pressures’ Predictions On Isolated Low-Rise Buildings Using Cfd Simulations, Md Faiaz Khaled, Aly Mousaad Aly

Faculty Publications

The aim of this paper is to enhance the accuracy of predicting time-averaged external surface pressures on low-rise buildings by utilizing Computational Fluid Dynamics (CFD) simulations. To achieve this, benchmark studies of the Silsoe cube and the Texas Tech University (TTU) experimental building are employed for comparison with simulation results. The paper is structured into three main sections. In the initial part, an appropriate domain size is selected based on the precision of mean pressure coefficients on the windward face of the cube, utilizing Reynolds Averaged Navier-Stokes (RANS) turbulence models. Subsequently, recommendations regarding the optimal computational domain size for an …

A Case Study Of Protecting Bridges Against Overheight Vehicles, Aly Mousaad Aly, Marc Hoffmann

Faculty Publications

Most transportation departments have recognized and developed procedures to address the ever-increasing weights of trucks traveling on bridges in service today. Transportation agencies also recognize the issues with overheight vehicles’ collisions with bridges, but few stakeholders have definitive countermeasures. Bridges are becoming more vulnerable to collisions from overheight vehicles. The exact response under lateral impact force is difficult to predict. In this paper, nonlinear impact analysis shows that the degree of deformation recorded through the modeling of the unprotected vehicle-girder model provides realistic results compared to the observation from the US-61 bridge overheight vehicle impact. The predicted displacements are 0.229 …

On The Computational Efficiency Of Les And Hybrid Rans-Les Models In Building Aerodynamics, Aly Mousaad Aly, Faiaz Khaled

Faculty Publications

Large-eddy simulation (LES) has proven to offer superior accuracy in regards to predicting surface pressures compared to the Reynolds-averaged Navier Stokes (RANS) models. However, the primary impediment is the high computational cost associated with LES. The authors attempt to investigate the computational cost and accuracy by employing different sub-grid scale (SGS) models in LES and hybrid RANS-LES models. One of the prerequisites of accurate pressure estimations is to ensure a horizontally homogeneous empty computational domain. This study aims to compare the computational competence qualitatively and quantitatively using an empty domain in regards to the ability to maintain horizontal homogeneity. The …

On The Computational Efficiency Of Les And Hybrid Rans-Les Models In Building Aerodynamics, Faiaz Khaled, Aly Mousaad Aly

Faculty Publications

No abstract provided.

Accelerated Controller Tuning For Wind Turbines Under Multiple Hazards, Aly Mousaad Aly, Milad Rezaee

Faculty Publications

During their lifecycle, wind turbines can be subjected to multiple hazard loads, such as high-intensity wind, earthquake, wave, and mechanical unbalance. Excessive vibrations, due to these loads, can have detrimental effects on energy production, structural lifecycle, and the initial cost of wind turbines. Vibration control by various means, such as passive, active, and semi-active control systems provide crucial solutions to these issues. We developed a novel control theory that enables semi-active controller tuning under the complex structural behavior and inherent system nonlinearity. The proposed theory enables the evaluation of semi-active controllers’ performance of multi-degrees-of-freedom systems, without the need for time-consuming …

Over Height Impact Avoidance And Incident Detection System, Suvash Chapain, Aly Mousaad Aly

Faculty Publications

During the construction and repair of bridges, work platforms or construction-related containment may result in restricted vertical clearances at a work location. Some tractor-trailer combinations are prone to over-height collisions at these locations. Collisions are a hazard to all drivers, and repair of the damage typically causes traffic delays. Appropriate solutions to this problem will focus on the prevention of collisions by detecting over-height vehicles and directing the drivers to take an alternate safe route. This presentation addresses the design and functionality of smart detection/alert systems that can be set up well in advance of a known vertical clearance restriction …

Peak Pressures On Low Rise Buildings: Cfd With Les Versus Full Scale And Wind Tunnel Measurements, Aly Mousaad Aly, Hamzeh Gol-Zaroudi

Faculty Publications

This paper focuses on the processes of wind flow in the atmospheric boundary layer, to produce realistic full-scale pressures for the design of low-rise buildings. CFD with LES turbulence closure is implemented on a scale 1:1 prototype building. A proximity study was executed computationally in CFD with LES that suggests new recommendations on the computational domain size, in front of a building model, apart from common RANS-based guidelines (e.g. COST and AIJ). Our findings suggest a location of the test building, different from existing guidelines, and the inflow boundary proximity influences pressure correlation and reproduction of peak loads. The CFD …

Reduction Of Structural Damage From The Thermal Expansion Of Concrete Using Multifunctional Materials, Darren Hartl, Mirmilad Mirsayar

Data

Corresponding data set for Tran-SET Project No. 18STTAM01. Abstract of the final report is stated below for reference:

"This study leveraged past successes in the analysis and design of shape memory alloy (SMA) components to address the issue of thermal expansion in concrete structures. Since the SMA used in the current work is relatively cheaper than other common SMAs (less than $50/lb compared to NiTi which is $200/lb due to difficulties in processing), it is anticipated that the findings of the study could be implemented in real infrastructures made of concrete, asphalt concrete, and other complex large infrastructure. Low-cost Fe-SMAs …

Soil-Recycled Aggregate-Geopolymer Road Base/Subbase Mixtures: Steps Towards Sustainability, Mohammad Khattak, Daniel Odion

Data

Corresponding data set for Tran-SET Project No. 18GTLSU10. Abstract of the final report is stated below for reference:

"This study deals with the development of Soil-Geopolymer mixtures using flyash, alkali activator and recycled aggregates (RAG) including recycled concrete (RCA) and reclaimed asphalt (RAP) as an alternative to soil-cement for pavement base and subbase layers. Several mix constituents were varied such as flyash type and content, RCA and RAP content and ratio of sodium silicate and sodium hydroxide. Experiment design was established and mechanical and durability characteristics of Soil-RAG-Geopolymer mixtures were evaluated and then compared to the conventional soil-cement mixtures. The …

The Impact Of Hurricane Harvey On Pavement Structures In The South East Texas And South West Louisiana, Stefan Romanoschi

Data

Corresponding data set for Tran-SET Project No. 18PUTA02. Abstract of the final report is stated below for reference:

"This study developed a methodology to estimate the damage caused by flooding, such that caused by Hurricane Harvey, on a road or street network. The flooded street or pavement sections are identified using GIS flood maps with street GIS maps used for pavement management systems (PMS) by cities or state authorities. Then the damage caused by flooding directly through the increase moisture in foundation layers or indirectly due to the increase heavy traffic during the relief effort is estimated. An example Excel …

Reduction Of Structural Damage From The Thermal Expansion Of Concrete Using Multifunctional Materials, Darren Hartl, Mirmilad Mirsayar

Publications

This study leveraged past successes in the analysis and design of shape memory alloy (SMA) components to address the issue of thermal expansion in concrete structures. Since the SMA used in the current work is relatively cheaper than other common SMAs (less than $50/lb compared to NiTi which is $200/lb due to difficulties in processing), it is anticipated that the findings of the study could be implemented in real infrastructures made of concrete, asphalt concrete, and other complex large infrastructure. Low-cost Fe-SMAs and other multifunctional materials can be considered as a replacement for components made of steel (e.g., in reinforced …

The Impact Of Hurricane Harvey On Pavement Structures In The South East Texas And South West Louisiana, Stefan Romanoschi

Publications

This study developed a methodology to estimate the damage caused by flooding, such that caused by Hurricane Harvey, on a road or street network. The flooded street or pavement sections are identified using GIS flood maps with street GIS maps used for pavement management systems (PMS) by cities or state authorities. Then the damage caused by flooding directly through the increase moisture in foundation layers or indirectly due to the increase heavy traffic during the relief effort is estimated. An example Excel macro was created to illustrate the estimation process. The methodology estimates the increase in rehabilitation costs since the …

Soil-Recycled Aggregate-Geopolymer Road Base/Subbase Mixtures: Steps Towards Sustainability, Mohammad Khattak, Daniel Odion

Publications

This study deals with the development of Soil-Geopolymer mixtures using flyash, alkali activator and recycled aggregates (RAG) including recycled concrete (RCA) and reclaimed asphalt (RAP) as an alternative to soil-cement for pavement base and subbase layers. Several mix constituents were varied such as flyash type and content, RCA and RAP content and ratio of sodium silicate and sodium hydroxide. Experiment design was established and mechanical and durability characteristics of Soil-RAG-Geopolymer mixtures were evaluated and then compared to the conventional soil-cement mixtures. The results of the testing showed that for the selected Soil-RAG-Geopolymer mixtures the strength, stiffness, permanent deformation, and durability …

Development Of Geopolymer-Based Cement And Soil Stabilizers For Transportation Infrastructure, Miladin Radovic, Anand Puppala

Data

Corresponding data set for Tran-SET Project No. 18CTAM03. Abstract of the final report is stated below for reference:

"Geopolymer Cement (GPC) has drawn much attention in the recent years as an alternative to Ordinary Portland Cement (OPC) for soil stabilization, pavements, bridges and other transportation structures due to their good mechanical properties in comparison to OPC. In addition, GPC can be processed at room temperatures from aqueous solutions of waste materials (e.g. fly ash) or abundant natural sources (e.g. clay), thereby significantly reducing CO2 production associated with processing of OPC. As such, GPC proves to be a more sustainable and …

Integrated Full-Scale Physical Experiments And Numerical Modeling Of The Performance And Rehabilitation Of Highway Embankments, Navid Jafari, Anand Puppala, Sayantan Chakroborty, Burak Boluk

Data

Corresponding data set for Tran-SET Project No. 18GTLSU06. Abstract of the final report is stated below for reference:

"The study aimed to fundamentally understand how soil strength and hydraulic properties are impacted by recurring cycles of wetting and drying induced by climate variability, with the practical implication of forecasting the stability of highway embankment slopes. The review of literature on the effects of long-term cyclic wetting-drying phases on hydro-mechanical properties of clayey soils suggests that only a few cycles of wetting and drying can impact the strength and hydraulic conductivity, where the latter can increase several orders of magnitude. Laboratory …

Performance Of Drilled Shaft Under Combination Of Complicated Loads Under Hurricane Event, Jie Huang, Sazzad Bin-Shafique

Data

Corresponding data set for Tran-SET Project No. 18GTTSA02. Abstract of the final report is stated below for reference:

"This project includes experimental and numerical studies to investigate and assess the impact of vertical loads on a laterally loaded drilled shaft under various conditions. The experimental study includes lab testing and lab-scale load test to examine a drilled shaft subjected to vertical and lateral loads at a reduced scale. With the data obtained from the lab-scale testing, a numerical model was calibrated, which was used to perform a parametric study to scrutinize the effect of many possible factors such as soil …

Mitigating Reflective Cracking Through The Use Of A Ductile Concrete Interlayer, Qian Zhang, Mohammad Khattak, Adway Das

Data

Corresponding data set for Tran-SET Project No. 18PLSU13. Abstract of the final report is stated below for reference:

"Reflective cracking is considered one of the most important issues that causes premature deterioration of composite pavements. Many types of mitigation methods have been studied in the past. However, they are either not effective in delaying the reflective cracking, or they only extend the service life by a few years. To address this critical issue and significantly extend the service life of the composite pavement, in this research, a ductile interlayer made of engineered cementitious composites (ECC) was proposed. It was hypothesized …

Strategies For Prioritizing Needs For Accelerated Construction After Hazard Events, Fernando Moreu, Chao Wang, Xinxing Yuan, Laleh Ghanbari, Claudia Garrido

Data

Corresponding data set for Tran-SET Project No. 18PPLSU04. Abstract of the final report is stated below for reference:

"There is a need for rapid and responsive infrastructure repair and construction after natural disaster events such as hurricanes, wildfires, and tornadoes. These natural disasters often shut down basic infrastructure systems, as experienced recently in several Region 6 states as well as in other states around the country. Accelerated construction practices are often used in these situations to speed up the traditional, and often slow, project delivery process. However, after a natural disaster, several and different types of transportation infrastructure components are …

Combining Virtual Reality And Machine Learning For Enhancing The Resiliency Of Transportation Infrastructure In Extreme Events, Supratik Mukhopadhyay, Yimin Zhu, Ravindra Gudishala

Data

Corresponding data set for Tran-SET Project No. 18ITSLSU09. Abstract of the final report is stated below for reference:

"Traffic management models that include route choice form the basis of traffic management systems. High-fidelity models that are based on rapidly evolving contextual conditions can have significant impact on smart and energy efficient transportation. Existing traffic/route choice models are generic and are calibrated on static contextual conditions. These models do not consider dynamic contextual conditions such as the location, failure of certain portions of the road network, the social network structure of population inhabiting the region, route choices made by other drivers, …

Toward Non-Corrosion And Highly Sustainable Structural Members By Using Ultra-High-Performance Materials For Transportation Infrastructure, Shih-Ho Chao, Ashish Karmacharya

Data

Corresponding data set for Tran-SET Project No. 18STUTA01. Abstract of the final report is stated below for reference:

"This research focused on investigating a highly sustainable and efficient reinforced concrete structural member for future infrastructure by utilizing emerging high-performance materials. These materials include ultra-high-performance fiber-reinforced concrete (UHP-FRC) and corrosion-resistant high-strength fiber-reinforced polymer (FRP) bars. Four reduced scale UHP-FRC specimens were tested under large displacement reversals to prove the proposed new ductile-concrete strong-reinforcement (DCSR) design concept by fully utilizing these ultra-high-performance materials. Micro steel fibers were incorporated into three specimens and ultra-high molecular weight polyethylene fibers were blended into the fourth …

Evaluating How The Quality Of Pedestrian Infrastructure Affects The Choice To Walk, Gregory Rowangould, Alexis Corning-Padilla

Data

Corresponding data set for Tran-SET Project No. 18PPUNM02. Abstract of the final report is stated below for reference:

"While the benefits of walking are well understood, the physical design of sidewalks and their maintenance needs generally receive much less attention in both research and practice than the infrastructure used by other modes of transportation. As a result, we know comparatively little about how the design of sidewalks and quality of the overall pedestrian environment affect the decision to walk. In our study we conducted a household travel survey to collect data on walking frequency and attributes related to sidewalk quality …

Development Of Geopolymer-Based Cement And Soil Stabilizers For Transportation Infrastructure, Miladin Radovic, Anand Puppala

Publications

Geopolymer Cement (GPC) has drawn much attention in the recent years as an alternative to Ordinary Portland Cement (OPC) for soil stabilization, pavements, bridges and other transportation structures due to their good mechanical properties in comparison to OPC. In addition, GPC can be processed at room temperatures from aqueous solutions of waste materials (e.g. fly ash) or abundant natural sources (e.g. clay), thereby significantly reducing CO2 production associated with processing of OPC. As such, GPC proves to be a more sustainable and environmentally friendly alternative than OPC. This research explores methods to develop GPC with desired properties and evaluate their …

Integrated Full-Scale Physical Experiments And Numerical Modeling Of The Performance And Rehabilitation Of Highway Embankments, Navid Jafari, Anand Puppala, Sayantan Chakraborty, Burak Boluk

Publications

The study aimed to fundamentally understand how soil strength and hydraulic properties are impacted by recurring cycles of wetting and drying induced by climate variability, with the practical implication of forecasting the stability of highway embankment slopes. The review of literature on the effects of long-term cyclic wetting-drying phases on hydro-mechanical properties of clayey soils suggests that only a few cycles of wetting and drying can impact the strength and hydraulic conductivity, where the latter can increase several orders of magnitude. Laboratory model-scale experiments of Louisiana and Texas soils are still ongoing and will relate the laboratory test results to …

Combining Virtual Reality And Machine Learning For Enhancing The Resiliency Of Transportation Infrastructure In Extreme Events, Supratik Mukhopadhyay, Yimin Zhu, Ravindra Gudishala

Publications

Traffic management models that include route choice form the basis of traffic management systems. High-fidelity models that are based on rapidly evolving contextual conditions can have significant impact on smart and energy efficient transportation. Existing traffic/route choice models are generic and are calibrated on static contextual conditions. These models do not consider dynamic contextual conditions such as the location, failure of certain portions of the road network, the social network structure of population inhabiting the region, route choices made by other drivers, extreme conditions, etc. As a result, the model’s predictions are made at an aggregate level and for a …

Mitigating Reflective Cracking Through The Use Of A Ductile Concrete Interlayer, Qian Zhang, Mohammad Khattak, Adway Das

Publications

Reflective cracking is considered one of the most important issues that causes premature deterioration of composite pavements. Many types of mitigation methods have been studied in the past. However, they are either not effective in delaying the reflective cracking, or they only extend the service life by a few years. To address this critical issue and significantly extend the service life of the composite pavement, in this research, a ductile interlayer made of engineered cementitious composites (ECC) was proposed. It was hypothesized that by adding a thin layer of highly ductile ECC material between the existing pavement and overlay, reflective …

Investigation Of Physical And Dynamic Properties Of High Porous Concrete, Ildar Akhmadullin

Publications

This project pursued two main objectives: (1) providing opportunities to Baton Rouge Community College (BRCC) students to develop hands-on laboratory skills and exposure to the transportation field, and (2) investigating porous concrete properties. Several BRCC student groups performed the work presented within this report; students prepared samples with different porosity and permeability according to standard specifications. The testing of the samples was performed at the Louisiana Transportation Research Center (LTRC) facility under the supervision of LTRC specialists. Findings indicate that the porosity of samples is backward proportional to the compression strength. This function is not linear but can be estimated …

Performance Of Drilled Shaft Under Combination Of Complicated Loads Under Hurricane Event, Jie Huang, Sazzad Bin-Shafique

Publications

This project includes experimental and numerical studies to investigate and assess the impact of vertical loads on a laterally loaded drilled shaft under various conditions. The experimental study includes lab testing and lab-scale load test to examine a drilled shaft subjected to vertical and lateral loads at a reduced scale. With the data obtained from the lab-scale testing, a numerical model was calibrated, which was used to perform a parametric study to scrutinize the effect of many possible factors such as soil stiffness, soil friction angle, and drilled shaft geometry. With all the factors considered in this study, the vertical …

Toward Non-Corrosion And Highly Sustainable Structural Members By Using Ultra-High-Performance Materials For Transportation Infrastructure, Shih-Ho Chao, Ashish Karmacharya

Publications

This research focused on investigating a highly sustainable and efficient reinforced concrete structural member for future infrastructure by utilizing emerging high-performance materials. These materials include ultra-high-performance fiber-reinforced concrete (UHP-FRC) and corrosion-resistant high-strength fiber-reinforced polymer (FRP) bars. Four reduced scale UHP-FRC specimens were tested under large displacement reversals to prove the proposed new ductile-concrete strong-reinforcement (DCSR) design concept by fully utilizing these ultra-high-performance materials. Micro steel fibers were incorporated into three specimens and ultra-high molecular weight polyethylene fibers were blended into the fourth specimen. One specimen with ASTM A1035 MMFX high-strength steel rebars, one with high-strength glass fiber reinforced polymer (GFRP) …

Evaluating How The Quality Of Pedestrian Infrastructure Affects The Choice To Walk, Gregory Rowangould, Alexis Corning-Padilla

Publications

While the benefits of walking are well understood, the physical design of sidewalks and their maintenance needs generally receive much less attention in both research and practice than the infrastructure used by other modes of transportation. As a result, we know comparatively little about how the design of sidewalks and quality of the overall pedestrian environment affect the decision to walk. In our study we conducted a household travel survey to collect data on walking frequency and attributes related to sidewalk quality and the quality of the walking environment in Albuquerque, New Mexico. We used summary statistics and statistical modeling …