Engineering Commons^™

Covalent Adaptable Networks For Wood Coatings, Jachin Boaz Clarke

Materials Engineering

Wood swells and shrinks causing problems with seasonal humidity. Applying thick coatings of reactive finishes based on cross-linked polyurethane, epoxy, or polyesters can slow moisture-vapor exchange. However, the use of thick coatings leads to cracking and crazing sooner than thin finishes. This research proposes the addition of 3.3 mol % triazabicyclodecene, a conventionally used covalent adaptable network catalyst, in a commercially available polyester-based wood coating. The self-healing of the wood coating is tested using DMA stress relaxation and compression molding. The result from DMA renders inconclusive and compression molding indicates the novel wood coating oxidizes at elevated temperatures. The wood …

Pressure Driven Desalination Membranes: Lyotropic Liquid Crystals Containing Single Walled Carbon, Matteo A. Del Giudice, Samantha Castillo Merigold

Materials Engineering

This project presents a potential alternative desalination technique that utilizes the ion rejection properties of single walled carbon nanotubes dispersed in a lyotropic liquid crystal (LLC) matrix. Previous research has pointed to the polymerizable surfactant methacryloxy ethyl hexadecyl dimethyl ammonium bromide (C16MA) having capabilities of filtering molecular components smaller than a nanometer, when oriented in cylindrical micelles. SWCNTs were dispersed in deionized water by probe sonication and addition of surfactant cetyltrimethylammonium bromide (CTAB) due to SWCNTs’ hydrophobic properties. Membranes were produced containing 55wt% C16MA, 37wt% DI water, 0.1wt% with respect to the monomer (WRM) SWCNTs, 1.9 wt% WRM 2,2-dimethoxy-2-phenylacetophenone (photointiator), …

Implementation Of Multivariate Artificial Neural Networks Coupled With Genetic Algorithms For The Multi-Objective Property Prediction And Optimization Of Emulsion Polymers, David Chisholm

Master's Theses

Machine learning has been gaining popularity over the past few decades as computers have become more advanced. On a fundamental level, machine learning consists of the use of computerized statistical methods to analyze data and discover trends that may not have been obvious or otherwise observable previously. These trends can then be used to make predictions on new data and explore entirely new design spaces. Methods vary from simple linear regression to highly complex neural networks, but the end goal is similar. The application of these methods to material property prediction and new material discovery has been of high interest …

Pnnl Dark Matter Bubble Chamber, Ryan Robinson

STAR Program Research Presentations

The Pacific Northwest National Laboratory (PNNL) prototype bubble chamber is intended to address issues encountered with the current PICO dark matter search detectors and improve the functionality of future experimental designs. The PNNL bubble chamber accomplishes this with a simplified interface between the hydraulic pressure controls and the target vessel and altering the standard chamber design such that it can be easily exchanged and replaced with vessels of various sizes and materials for testing purposes. The chamber itself is a glass vessel which houses perfluorobutane and holds the target fluid above room temperature and atmospheric pressure. The target fluid becomes …

Preparation Of Supramolecular Amphiphilic Cyclodextrin Bilayer Vesicles For Pharmaceutical Applications, Kate E. Frischkorn

Master's Theses

Recent pharmaceutical developments have investigated using supramolecular nanoparticles in order to increase the bioavailability and solubility of drugs delivered in various methods. Modification of the carbohydrate cyclodextrin increases the ability to encapsulate hydrophobic pharmaceutical molecules by forming a carrier with a hydrophobic core and hydrophilic exterior. Guest molecules are commonly added to these inclusion complexes in order to add stability and further increase targeting abilities of the carriers. One such guest molecule is adamantine combined with a poly(ethylene glycol) chain. Vesicles are formed by hydrating a thin film of amphiphilic cyclodextrin and guest molecules in buffer solution that mimics physiological …

Usage Of Fomblin Y To Improve Water Repellence Of Surface Coatings, Shawn Pj Kirby, Jeffrey Alston, Andrew Guenthner

STAR Program Research Presentations

Fluoro-Decyl POSS (FDP) has shown strong potential as a water repellant surface coating. Additionally, Fomblin is a solvent believed to have the ability to control the crystallization of POSS compounds on surfaces. Controlling the crystallization is key to improving water repelling abilities of surfaces. Thus, dip coating FDP and Fomblin onto surfaces is being investigated for water repulsion, mechanical stability, and deposition feasibility. First, temperature dependence of solubility of Fluoro-Decyl POSS in Fomblin was tested using Dynamic Light Scattering. Relative water repelling abilities of different coatings were determined by measuring contact angle of surfaces with water. Coatings with and without …

Comparative Solubility Of Poss Compounds In Fomblin Y, Shawn Pj Kirby, Jeffrey Alston, Andrew Guenthner

STAR Program Research Presentations

Fluoro-Decyl POSS (FDP) has shown strong potential as a water repellant surface coating. Additionally, Fomblin is a solvent believed to have the ability to control the crystallization of POSS compounds on surfaces. Controlling the crystallization is key to improving water repelling abilities of surfaces. Thus, dip coating FDP and Fomblin onto surfaces is being investigated for water repulsion, mechanical stability, and deposition feasibility. However, in order for this to be successful, POSS must be soluble in Fomblin. Temperature dependence of solubility of Fluoro-Hexyl, Fluoro-Octyl, Fluoro-Decyl POSS in Fomblin was tested using Dynamic Light Scattering. The values were compared, and it …

A Comparison Study Of Two Synthesis Methods For Polymer Of Intrinsic Microporosity 1 (Pim-1), Conor S. Perry

Materials Engineering

Polymers of Intrinsic Microporosity (PIMs) are an emerging polymeric material class for molecular sieving applications. This study focuses on PIM-1, an alternating copolymer of 5,5’,6,6’-tetrahydroxy-3,3’,3,3’-tetramethyl-1,1’-spirobisindane and tetrafluoroterephthalonitrile synthesized via nucleophilic aromatic substitution. PIM-1 been widely studied as a gas separating material and filtering membrane, but in this case, it is studied as a battery separator material. PIM-1’s microporous (pore diameters less than 2 nm) structure allows smaller favorable ions to transport while preventing larger ions and compounds from transporting. Two synthesis methods, round bottom flask synthesis and ball mill synthesis, of PIM-1 are compared to see any improved characteristics. The …

Effect Of Surface Treatment On Liquid Adhesion Inside 3-D Structures, Madani A. Khan, Jeffrey Alston, Andrew Guenthner, Jacob Zavala

STAR Program Research Presentations

This study explores the relationship between chemical surface treatments on the interior of glass tubes and their resistance to fluid flow. By treating the interior of the tubes with functional silanes we can decrease or increase the interaction of the tube walls with the fluid column, which translates to changes in fluid column height for a given pressure differential. Resistance to fluid flow is quantified by using the tubes as integral parts of a barometric pressure column and measuring the changes in column height as the fluid is pulled into the tube by a set pressure differential. The barometric pressure …

Gc Verification Of The Spacecraft Atmosphere Monitor, Jessica S. Castro, Richard D. Kidd, Jeffrey D. Hein

STAR Program Research Presentations

International Space Station crew members face the unique challenge of maintaining air quality due to the volatile organic compounds (VOCs) that have the potential to accumulate at unsafe levels. The Spacecraft Atmosphere Monitor (SAM) is a miniature gas chromatograph/mass spectrometer (GCMS) designed to measure major constituents (such as N₂, O₂ and CO₂) and trace VOCs within the cabin of the spacecraft. The gas chromatograph is responsible for separating the sample into its components in order to be characterized. The oven of the gas chromatograph must reach a temperature of 150°C in order to heat constituents …

Using In Situ Liquid Single Photon Ionization Mass Spectrometry (Spi-Ms) To Probe Lithium Polysulfide Electrolyte In Motion, Aala M. Al Hasan, Jiachao Yu, Juan Yao, Vijayakumar Murugesan, Manjula Nandasiri, Xiao-Ying Yu

STAR Program Research Presentations

The solid-liquid (s-l) interface is the most common interface encountered in electrochemical systems. The s-l interface has wide applications in energy storage, catalysis, and material sciences. In situ studies of chemical reactions taking place on the s-l interfaces can further our understanding of electron transfer and link to real-world device functions under challenging conditions. Direct probing of the solid electrode and liquid electrolyte interface has been realized using a vacuum compatible electrochemical microfluidic reactor, system for analysis at the liquid vacuum interface (SALVI) with time-of-flight secondary ion mass spectrometry (ToF-SIMS). Most recently, the electrochemical version of SALVI was integrated to …

Metals Additive Manufacturing Powder Aging Characterization, Thomas Russell Lovejoy, Nicholas Karl Muetterties, David Takeo Otsu

Mechanical Engineering

The metallic additive manufacturing process known as selective laser melting requires highly spherical, normally distributed powder with diameters in the range of 10 to 50 microns. Previous observations have shown a degradation in powder quality over time, resulting in unwanted characteristics in the final printed parts. 21-6-9 stainless steel powder was used to fabricate test parts, with leftover powder recycled back into the machine. Powder samples and test specimens were characterized to observe changes across build cycles. Few changes were observed in the physical and mechanical properties of the specimens, however, there were indications of chemical changes across cycles. Potential …

Production And Harvest Of Microalgae In Wastewater Raceways With Resource Recycling, Alexander Colin Roberts

Master's Theses

Microalgae can be grown on municipal wastewater media to both treat the wastewater and produce feedstock for algae biofuel production. However the reliability of treatment must be demonstrated, as well as high areal algae productivity on recycled wastewater media and efficient sedimentation harvesting. This processes was studied at pilot scale in the present research.

A pilot facility was operated with nine CO₂-supplemented raceway ponds, each with a 33-m² surface area and a 0.3-m depth, continuously from March 6, 2013 through September 24, 2014. The ponds were operated as three sets of triplicates with two sets continuously fed …

Effect Of Surface Omniphobicity On Drying By Forced Convection, Madani A. Khan, Jeffrey Alston, Andrew Guenthner

STAR Program Research Presentations

Low energy surfaces can strongly repel both oil and water. Recently these surfaces have been fabricated on various substrates including fabric, aluminum, stainless steel and many other materials. In this experiment we explore the use of low energy surface deposition on aluminum alloy, stainless steel and silicon substrates, to enhance the drying rate of liquids removed from the surface by forced convection. We control surface roughness by substrate abrasion and by the growth of Al₂O₃ nanograss to enhance liquid repellence by use of a hierarchical texture. Liquid repellence of the substrates is measured by contact angles of …

Wet Chemical Synthesis And Characterization Of Nanomaterials For Solar Cell Applications, Krystle N. Sy, Ramprasad Gandhiraman, Jessica E. Koehne

STAR Program Research Presentations

During long term space missions, it is necessary to have a reliable source of energy. Solar cells are an easy and reliable way to convert energy from the sun to electrical energy. NASA has used solar cells manufactured on Earth as an energy source for many of its missions. In order to develop technologies that will enable high efficiency solar cells, we are synthesizing nanostructured materials. A range of nanostructured materials, such as titanium dioxide nanowires, nickel nanoparticles, copper nanoparticles, and silver nanoparticles/nanowires, are synthesized. In this work, we are reporting on the synthesis of these nanomaterials and the electron …

Effect Of Surfactant Architecture On Conformational Transitions Of Conjugated Polyelectrolytes, Greg A. Braggin

Master's Theses

Water soluble conjugated polyelectrolytes (CPEs), which fall under the category of conductive polymers, possess numerous advantages over other conductive materials for the fabrication of electronic devices. Namely, the processing of water soluble conjugated polyelectrolytes into thin film electronic devices is much less costly as compared to the processing of inorganic materials. Moreover, the handling of conjugated polyelectrolytes can be performed in a much more environmentally friendly manner than in the processing of other conjugated polymers because conjugated polyelectrolytes are water soluble, whereas other polymers will only dissolve in toxic organic solvents. The processing of electronic devices containing inorganic constituents such …

Does A Plastron Improve Heat Transfer?, Madani A. Khan, Jeffrey Alston, Andrew Guenthner

STAR Program Research Presentations

Superamphiphobic surfaces strongly repel both water and oils. In this work, aluminum coupons are processed by sanding with various grit of sand paper to impart microscale roughness. Subsequent submersion of the aluminum substrate in boiling water grows nanoscale grass-like structures. The oxide layer of Al is slightly soluble in water. During a fast diffusion/equilibrium, Al₂O₃ nanograss grows on the surface. A low energy coating is then deposited on the surface. The micro and nanoscale features create re-entrant structures that trap air enabling contact liquid to be in a Cassie-Baxter state. Superamphiphobicity of the samples were confirmed by …

Formulation Development Of A Polymer-Drug Matrix With A Controlled Release Profile For The Treatment Of Glaucoma, Eric W. Tsoi

Master's Theses

Glaucoma is the leading cause of blindness in the United States accounting for 9-12% of all cases of blindness. Currently, the front line treatment for glaucoma are prostaglandins that may have to be taken up to several times a day. Even with proper treatment, roughly 11% of the patients using the treatment are non-compliant and lose their vision. In this project, ForSight Laboratories has developed a pharmaceutical drug delivering implant with the capability of sustaining long-term release of a prostaglandin as a new way to treat the condition. This project reports the product development of a polymer drug matrix with …

Lipid Production By Microalgae Treating Municipal Wastewater, James Edward Kelley

Master's Theses

Microalgae hold much promise as a feedstock in liquid biofuel production. Lipid content of microalgae cells range from 30-80% dry weight of biomass. It is projected that microalgae can produce between 1,000-6,500 gallons/acre/year of oil. Currently, production of industrial algae operates in open raceway ponds that use minimal capital and energy inputs to culture algae. Raceway ponds can also be used to grow microalgae from municipal waste streams. Although high biomass productivity can be achieved in these systems, there remains a large production gap between large volumes of biomass cultivation and high lipid content from microalgae cells. Low lipid content …

Optimizing Electrode Design For Microbial Fuel Cells Used For Wastewater Treatment, Lindsay Nichols, John A. Hogan

STAR Program Research Presentations

Microbial fuel cells (MFC) utilize bacteria to generate an electrical current that can be used in the decomposition of sludge and human urine. In a MFC there is an anode (for oxidation of organic compounds), cathode (reduction of oxygen or carbon dioxide), and a proton exchange membrane (PEM, allows protons to migrate); reduction-oxidation reactions between the anode and cathode produce a measurable current. Bacteria that are found in sludge can be used to produce electrons in a voltaic cell, but optimizing conditions for harnessing the energy is crucial to making a MFC efficient. Research has shown that the ratios of …

Investigation Of Spillover Effect To Enhance Hydrogen Storage, Sarah C. Corrigan, Lin Simpson, Thomas Gennett

STAR Program Research Presentations

Hydrogen is an attractive energy option because of its low
environmental impact, but a critical problem is its low energy
density, which makes it difficult to store. For example, the US
Department of Energy (DOE) hydrogen plan for fuel cell powered
vehicles requires a gravimetric density of 6.5 wt%. There are several
existing hydrogen storage methods, including compressed gas,
liquefaction, metal hydrides, and physisorption, but at present, none
of these technologies comes close to achieving the targets set by the
DOE. Although chemical storage methods have been claimed to be the
most promising hydrogen storage technology, and activated carbons the …

Effect Of Au Content On Microstructural Evolution Of Snagcu Solder Joints That Undergo Isothermal Aging And Reliability Testing, Patrick J. Hyland

Master's Theses

Electronics, especially, printed circuit boards (PCBs) are a widespread technology. Metal coatings or “surface finishes” are often added to PCB board pads and component leads during manufacturing to improve their performance. Electroplated nickel/gold over copper is a popular surface finish for printed circuit boards and component leads. The presence of gold in solder joints, however, is known to have detrimental effects referred to as gold embrittlement. It is generally understood that tin-lead solder joints with less than 3 weight percent (wt%) of gold will not experience reliability issues. The acceptable level of gold in lead-free solder joints, however, is less …

Artificial Muscle Project: Process Development Of Polydimethyl Siloxane Thin Films For Use In Dielectric Electroactive Polymer Artificial Muscle Actuators, Vincent J. Gayotin, Richard W. Morrison, Paul A. Preisser

Materials Engineering

An artificial muscle design was created founded on the principles of a dielectric electroactive polymer (DEAP), which is fundamentally similar to a capacitor. A polydimethyl siloxane (PDMS)-based elastomer, Sylgard 184 from Dow Corning, was chosen for the design and spun coat onto polystyrene (PS) Petri dishes at varying speeds to create a thin film, using speeds of 2000 rpm, 3000 rpm, 4000 rpm, 5000 rpm, and 6000 rpm. The film thicknesses were measured optically through use of a microscope with coupled computer imaging software to generate a characteristic curve of film thickness to spin speed, achieving a minimum film thickness …

The Effects Of Cure Schedule On Properties Of Glass-Fiber Reinforced Epoxy Matrix Composites, Trevor J. Lee

Materials Engineering

Two different two-component resin systems were cured, via Differential Scanning Calorimetry, for the times recommended by their respective manufacturers. The resin cure schedules were designed to simulate typical and attainable processing conditions; they were cured at 120°F, 140°F, and 160°F, and in-mold post-cured at 200°F, 230°F, and 260°F. The resulting scans were then compared to a baseline cure for each resin system, consisting of two heating-cooling cycles at a constant rate of temperature change. These baseline cures were then used to determine the percent cure of each sample and the shift in glass transition temperature between the baseline cure and …