Engineering Commons^™

Electrochemical Behavior Of Dense Electrodes For Impedancemetric Nox Sensors, Nabamita Pal

Doctoral Dissertations

NOx (NO and NO2) exhaust gas sensors for diesel powered vehicles have traditionally consisted of porous platinum (Pt) electrodes along with a dense ZrO2 based electrolyte. Advancement in diesel engine technology results in lower NOx emissions. Although Pt is chemically and mechanically tolerant to the extreme exhaust gas environment, it is also a strong catalyst for oxygen reduction, which can interfere with the detection of NOx at concentrations below 100 ppm. Countering this behavior can add to the complexity and cost of the conventional NO x sensor design. Recent studies have shown that dense electrodes are less prone to heterogeneous …

Synthesis, Characterization, And Activity Of Co/Fe Alumina/Silica Supported Ft Catalysts And The Study Of Promoter Effect Of Ruthenium, Sunday Azubike Esumike

Doctoral Dissertations

The alumina and hybrid alumina-silica FT catalyst were prepared by one-step solgel/oil-drop methods using metal-nitrate-solutions (method-I), and nanoparticle-metaloxides (method-2). The nanoparticle-metal-oxides did not participate in solubility equilibria in contrast to metal nitrate in method-1 causing no metal ion seepage; therefore, method-2 yields higher XRF metal loading efficiency than method-1. The thermal analysis confirmed that the metal loading by method-1 and method-2 involved two different pathways. Method-1 involves solubility equilibria in the conversion of metal-nitrate to metal- hydroxide and finally to metal-oxide, while in method-2 nanoparticle-metal-oxide remained intact during sol-gel-oil-drop and calcination steps.

The alumina supported catalysts were dominated by γ-alumina …

Immobilization Of Cellulase For Large Scale Reactors To Reduce Cellulosic Ethanol Cost, Dezhi Zhang

Doctoral Dissertations

Cellulosic ethanol is an alternative renewable energy source. Cellulase used in the production of cellulosic ethanol is very expensive. The difficulty in separating cellulase from the cellulose solution after the hydrolysis process limits the reusability of the cellulase, which highly precludes the scales of this application because of the high cost of the enzyme. Immobilization of cellulase provides a promising approach to allow the enzyme to be recycled, thus reducing the production cost. This research focused on immobilizing cellulase for reuse to reduce the cellulosic ethanol cost.

Four immobilization techniques were explored for the immobilization of cellulase on four different …

Multiscale Modeling Study Of Methanol Oxidation By Ion-Modified Mdh Enzymes, Purnima Kharidehal

Doctoral Dissertations

Enzymes have been considered as molecular electrocatalysts due to their extraordinary characteristics such as their ability to accelerate reactions enormously, to operate under physiological conditions, and to produce fewer by-products during a catalytic reaction. However, enzyme based fuel cells have been reported to have power output and stability limitations, which are restricting the use of this kind of fuel cell to small electronic devices. Methanol dehydrogenase (MDH) is one such enzyme, which oxidizes methanol and other primary alcohols to their corresponding aldehydes. The active site of MDH contains a divalent cation (Ca2+), a co-factor pyrrolo-quinoline quinone (PQQ), several amino acids, …

Computational Studies Of Ion Transport In Polymer Electrolytes, Hui Wu

Doctoral Dissertations

Improving ionic conductivity and lithium mobility in polymer electrolytes is important for their practical use for battery electrolytes. In this study, a combination of molecular dynamics and Monte Carlo simulations was used to bring insight into lithium ion transport in poly(ethylene oxide) (PEO) with plasticizers and also next to alumina solid surface doped with lithium salt. The simulations were performed using a moderately high molecular weight polymer (Mn = 10,000 g/mol) at an EO:Li ratio of 15. For the plasticized system, the PEO with LiN(CF3SO 2)2 (LiTFSI) was mixed with 10 wt% plasticizers that included either cyclic ethylene carbonate …

Modeling And Experimental Verification Of Growth Of An Axisymmetric Cylindrical Rod By Three-Dimensional Laser-Induced Chemical Vapor Deposition, Qing Chen

Doctoral Dissertations

Three-dimensional laser-induced chemical vapor deposition (3D-LCVD) is a recently developed micro-manufacturing process that holds great potential for the production of complex microstructures with high aspect ratio. A laser beam is focused through a vacuum chamber window onto a movable substrate. The heat from the laser at or near the focal spot on the substrate induces the decomposition reaction of precursor gas in the chamber. As a result, solid-phase reaction products are deposited on the substrate to form the microstructure. In this dissertation, a numerical model is developed for simulating kinetically-limited growth of an axisymmetric cylindrical rod by pre-specifying the surface …