Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 5 of 5
Full-Text Articles in Engineering
Hip And Knee Biomechanics For Transtibial Amputees In Gait, Cycling, And Elliptical Training, Greg Orekhov
Hip And Knee Biomechanics For Transtibial Amputees In Gait, Cycling, And Elliptical Training, Greg Orekhov
Master's Theses
Transtibial amputees are at increased risk of contralateral hip and knee joint osteoarthritis, likely due to abnormal biomechanics. Biomechanical challenges exist for transtibial amputees in gait and cycling; particularly, asymmetry in ground/pedal reaction forces and joint kinetics is well documented and state-of-the-art passive and powered prostheses do not fully restore natural biomechanics. Elliptical training has not been studied as a potential exercise for rehabilitation, nor have any studies been published that compare joint kinematics and kinetics and ground/pedal reaction forces for the same group of transtibial amputees in gait, cycling, and elliptical training. The hypothesis was that hip and knee …
Subject-Specific Finite Element Predictions Of Knee Cartilage Pressure And Investigation Of Cartilage Material Models, Michael G. Rumery
Subject-Specific Finite Element Predictions Of Knee Cartilage Pressure And Investigation Of Cartilage Material Models, Michael G. Rumery
Master's Theses
An estimated 27 million Americans suffer from osteoarthritis (OA). Symptomatic OA is often treated with total knee replacement, a procedure which is expected to increase in number by 673% from 2005 to 2030, and costs to perform total knee replacement surgeries exceeded $11 billion in 2005. Subject-specific modeling and finite element (FE) predictions are state-of-the-art computational methods for anatomically accurate predictions of joint tissue loads in surgical-planning and rehabilitation. Knee joint FE models have been used to predict in-vivo joint kinematics, loads, stresses and strains, and joint contact area and pressure. Abnormal cartilage contact pressure is considered a risk factor …
Microenvironment Regulates Fusion Of Breast Cancer Cells, Peiran Zhu
Microenvironment Regulates Fusion Of Breast Cancer Cells, Peiran Zhu
Masters Theses
Fusion of cancer cells has been observed in tumors for more than a century and is thought to contribute to tumor development and drug resistance. The low frequency of cell fusion events and the instability of fused cells have hindered our ability to understand the molecular mechanisms that govern cell fusion. We have developed a patterned gel system that can isolate cell fusion events and we demonstrate that several breast cancer cell lines can fuse into multinucleated giant cells in vitro, and the initiation and longevity of fused cells can be regulated solely by biophysical factors. Dynamically tuning the adhesive …
Knee Angles And Axes Crosstalk Correction In Gait, Cycling, And Elliptical Training Exercises, Jordan M. Skaro
Knee Angles And Axes Crosstalk Correction In Gait, Cycling, And Elliptical Training Exercises, Jordan M. Skaro
Master's Theses
When conducting motion analysis using 3-dimensional motion capture technology, errors in marker placement on the knee results in a widely observed phenomenon known as “crosstalk” [1-18] in calculated knee joint angles (i.e., flexion-extension (FE), adduction-abduction (AA), internal-external rotation (IE)). Principal Component Analysis (PCA) has recently been proposed as a post hoc method to reduce crosstalk errors and operates by minimizing the correlation between the knee angles [1, 2]. However, recent studies that have used PCA have neither considered exercises, such as cycling (C) and elliptical training (E), other than gait (G) nor estimated the corrected knee axes following PCA correction. …
Design And Analysis Of A 3d-Printed, Thermoplastic Elastomer (Tpe) Spring Element For Use In Corrective Hand Orthotics, Kevin Thomas Richardson
Design And Analysis Of A 3d-Printed, Thermoplastic Elastomer (Tpe) Spring Element For Use In Corrective Hand Orthotics, Kevin Thomas Richardson
Theses and Dissertations--Mechanical Engineering
This thesis proposes an algorithm that determine the geometry of 3D-printed, custom-designed spring element bands made of thermoplastic elastomer (TPE) for use in a wearable orthotic device to aid in the physical therapy of a human hand exhibiting spasticity after stroke. Each finger of the hand is modeled as a mechanical system consisting of a triple-rod pendulum with nonlinear stiffness at each joint and forces applied at the attachment point of each flexor muscle. The system is assumed quasi-static, which leads to a torque balance between the flexor tendons in the hand, joint stiffness and the design force applied to …