Engineering Commons^™

Reaction Wheels Fault Isolation Onboard 3-Axis Controlled Satellite Using Enhanced Random Forest With Multidomain Features, Mofiyinoluwa Oluwatobi Folami

Electronic Theses and Dissertations

With the increasing number of satellite launches throughout the years, it is only natural that an interest in the safety and monitoring of these systems would increase as well. However, as a system becomes more complex it becomes difficult to generate a high-fidelity model that accurately describes all the system components. With such constraints using data-driven approaches becomes a more feasible option. One of the most commonly used actuators in spacecraft is known as the reaction wheel. If these reaction wheels are not maintained or monitored, it could result in mission failure and unwarranted costs. That is why fault detection …

Multilateration Index., Chip Lynch

Electronic Theses and Dissertations

We present an alternative method for pre-processing and storing point data, particularly for Geospatial points, by storing multilateration distances to fixed points rather than coordinates such as Latitude and Longitude. We explore the use of this data to improve query performance for some distance related queries such as nearest neighbor and query-within-radius (i.e. “find all points in a set P within distance d of query point q”). Further, we discuss the problem of “Network Adequacy” common to medical and communications businesses, to analyze questions such as “are at least 90% of patients living within 50 miles of a covered emergency …

Flight Trajectory Prediction For Aeronautical Communications., Nathan T Schimpf

Electronic Theses and Dissertations

The development of future technologies for the National Airspace System (NAS) will be reliant on a new communications infrastructure capable of managing a limited spectrum among aircraft and ground systems. Emerging approaches to this spectrum allocation task mostly consider machine learning techniques reliant on aircraft and Air Traffic Control (ATC) sector data. Much of this data, however, is not directly available. This thesis considers the development of two such data products: the 4D trajectory (latitude, longitude, altitude, and time) of aircraft, and the anticipated airspace utilization and communication demand within an ATC sector. Data predictions are treated as a time …

Interfacial Heat Transfer In Squeeze Casting Of Cast Al Alloy A380 And Mg Alloy Az91 And Wrought Alloy Az31, Luyang Ren

Electronic Theses and Dissertations

The weight reduction of vehicles and airplanes in the automotive and aerospace industries is urgently needed due to the government regulation and market demand. To satisfy engineering performance of lightweight auto and aero components, high strength light alloys such as aluminum (Al) or magnesium (Mg) alloys are usually adopted. This study was intended to explore a solution for casting high strength cast and wrought Al and Mg alloys. Before light alloys can be utilized for mass production, critical processing parameters need to be accurately determined. The interfacial heat transfer coefficient is one of the most important factors in casting processes. …

Development Of Triangular And Tetrahedral Finite Elements For Solutions To Thermoelastic Instabilities Using Hotspotter, Cortney Samuel Leneave

Electronic Theses and Dissertations

The objective of the work presented in this thesis is to develop first-order triangular and tetrahedral elements for solutions to Thermoelastic Instabilities (TEI) regarding sliding friction systems in Hotspotter.

Hotspotter software uses a finite element method and an eigenvalue method and is an important tool because currently no other commercial software exists which solves the TEI problem for critical velocities and wave numbers of a system. Hotspotter currently uses quadrilateral and hexahedral elements for two and three dimensional analysis, respectively. Typically, tri and tet elements are used in industry when doing static and dynamic stress analysis. Therefore, the Hotspotter user …

Experimental And Numerical Investigation Of Naca Airfoil Wing With Winglets, Courtney Danielle Bachmann

Electronic Theses and Dissertations

This research was performed in order to study wingtip devices and, in particular, winglets. Winglets are attached to commercial aircraft for the purpose of reducing induced drag caused by wake vortices on the wingtip. A winglet device can save an aircraft anywhere from 3-7% in fuel consumption. Over the course of a year, this can add up to hundreds of thousands of dollars saved. This research consisted of two parts: one part experiment and one part equipment design. The latter phase of this research examined various methods of testing in a subsonic wind tunnel laboratory setting. Experimental results found with …

Mechanical Properties Of Nanomodified Hybrid Gfrp Composite Materials, Micah Rop Kimutai

Electronic Theses and Dissertations

The mechanical behavior of the nanomodified hybrid epoxy matrix was investigated in glass fiber reinforced plastics (GFRP). In this study, five nanocomposites enriched with as received halloysite, nanomer I.28E, HNT-APTES, and the hybrid combinations of the two HNTs with the nanomer I.28E were successfully fabricated. To evaluate the effects and morphological characteristics of the individual fillers and the hybrid configurations on the epoxy resin matrix, TGA, DSC, and DMA were analyzed. To understand the effect of the five configurations on the neat GFRP laminate, mode I interlaminar fracture toughness, tensile, and vibration properties were investigated. Electron microscopy testing techniques were …