Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons

Open Access. Powered by Scholars. Published by Universities.®

Articles 1 - 6 of 6

Full-Text Articles in Engineering

The Differences Are Not So Great: High Altitude Balloon And Small Spacecraft Software Development, Jeremy Straub, Ronald Marsh Jun 2014

The Differences Are Not So Great: High Altitude Balloon And Small Spacecraft Software Development, Jeremy Straub, Ronald Marsh

Jeremy Straub

Previous work discussed critical differences in planning, developing hardware for and executing a high altitude balloon (HAB) mission. One area where this difference is less pronounced is in software development, allowing HABs to be utilized as a ‘software testbed’ for many orbital missions. This paper provides an overview of the software development process for both orbital and HAB craft, highlighting differences between the two processes and the numerous similarities. It concludes by presenting a framework for analyzing the suitability of HAB testing for small satellite software.


A Low-Cost Gps/Inertial Position Determination System For High Altitude Balloons, Spacecraft And Unmanned Aerial Systems, Tyler Leben, Jeremy Straub, Ronald Marsh Mar 2014

A Low-Cost Gps/Inertial Position Determination System For High Altitude Balloons, Spacecraft And Unmanned Aerial Systems, Tyler Leben, Jeremy Straub, Ronald Marsh

Jeremy Straub

A low-cost system is needed to determine precise position and predict future location in flight and low-Earth orbit. One method to accomplish this task is to utilize an onboard GPS receiver. GPS units receive data from the GPS NAVSTAR constellation of 24 satellites in the form of a 37 byte ASCII text sent at 4800 baud called NMEA sentences. The standard is 1 HZ, which is one sentence per second, but can be more. Ideally, from this data a PVT (position, velocity, time) and altitude can be determined. This data is then transferred from the GPS module to a separate …


The Path To Regulation Of Small Unmanned Aerial Vehicles In The United States, Jeremy Straub, Joe Vacek Mar 2014

The Path To Regulation Of Small Unmanned Aerial Vehicles In The United States, Jeremy Straub, Joe Vacek

Jeremy Straub

This poster presents an overview of proposed regulations that are presented in [1] related to a re-vised approach to small Unmanned Aerial Vehicles (UAV) regulation in the United States. Prospective strategies for enhancing UAV regulation are consid-ered as is the pathway to develop and implement these regulations. The benefits of changing the UAV regulatory regime are discussed, on both a user/prospective user and societal scale.


The Use Of Solar Balloons At Und As A Low-Cost Alternative To Helium Balloons For Small Spacecraft Testing And Stem Education, John Nordlie, Jeremy Straub, Chris Theisen, Ronald Marsh Mar 2014

The Use Of Solar Balloons At Und As A Low-Cost Alternative To Helium Balloons For Small Spacecraft Testing And Stem Education, John Nordlie, Jeremy Straub, Chris Theisen, Ronald Marsh

Jeremy Straub

Helium-filled latex weather balloons have been utilized for many years to carry small satellite prototypes and subsystems into the stratosphere to allow testing in a “near space” (stratospheric) environment. A variety of environmental factors similar to the space environment can be found in this region, such as a rarified atmosphere, increased thermal stress including very low temperatures, increased solar radiation, the necessity of remote command and control, tracking, and telemetering of data. While this method of flight testing has been well-proven, a recent increase in the price of helium has driven the cost of such test programs to much higher …


The Use Of 3d Printing To Enable High Altitude Balloon Missions, Jeremy Straub Mar 2014

The Use Of 3d Printing To Enable High Altitude Balloon Missions, Jeremy Straub

Jeremy Straub

The 3D printing technology allows the low-cost creation of structures based on user-defined configuration parameters. Unlike other plastic-forming technologies, there is no tooling cost related to the creation of a mold. Because of this, highly-customized structures can be created with a minimum production quantity of one, allowing adaptation to individual mission needs (for a single-HAB mission) or the change of the structure across a multi-unit run (e.g., to test various configurations or as part of a study requiring multiple payloads with different configurations).

This paper considers the mission possibilities enabled by the use of 3D printing for HAB structures. These …


Solar Ballooning: A Low-Cost Alternative To Helium Balloons For Small Spacecraft Testing, John Nordlie, Jeremy Straub, Chris Theisen, Ronald Marsh Jan 2014

Solar Ballooning: A Low-Cost Alternative To Helium Balloons For Small Spacecraft Testing, John Nordlie, Jeremy Straub, Chris Theisen, Ronald Marsh

Jeremy Straub

Helium-filled latex weather balloons have been utilized to carry small satellite prototypes and subsystems into the stratosphere to allow testing in a “near space” environment. This provides a variety of environmental factors similar to the space environment, such as a rarified atmosphere, increased thermal stress, increased solar radiation, the necessity of remote command and control, tracking, and telemetering of data. While this method of flight testing has been well-proven, a recent spike in the price of helium has driven the cost of such test programs to much higher levels. In this poster, an alternative technology to provide the flight mechanism, …