Engineering Commons^™

Boundary Layer Measurements On The Bolt Ii Geometry Using Pressure And Temperature Sensitive Paints, Jacob Gaetano Butera

Masters Theses

Hypersonic vehicles are subjected to an extreme aerothermodynamic environment dominated by intense thermal loading which is amplified further when the local boundary layer state transitions from a laminar to a turbulent state. Due to weight and complexity considerations, it is not feasible to incorporate thermal protection systems (TPS) over an entire hypersonic body. Therefore, it is critically important to identify and predict where the boundary layer will undergo transition such that the thermal protection system can be focused on the most at-risk areas. This work attempts to observe boundary layer transition on the Boundary Layer Transition (BOLT) II flight test …

Computational Analysis Of Steady Hypersonic Flow Fields Of Nasa Benchmark Geometries Utilizing Ansys Fluent, Aidan Murphy

McKelvey School of Engineering Theses & Dissertations

The Hypersonic International Flight Research Experimentation (HIFiRE) program explores and advances hypersonic aerospace systems by developing a multitude of test flight geometries and conducting experimental test flights to obtain data for use in validation of computational models and results. This study focuses on computational validation of heat flux, and calculation of static pressure profiles, skin friction coefficient profiles, and flow contours. The flow fields studied are for Mach number 7.18 and angles of attack (α) of 0° & 2°. These flow fields include many compressible flow features such as an expansion wave at the intersection of the cone and flat …

An Experimental Investigation Of The Effect Of Narrowband Freestream Noise On Fundamental Transitional Shockwave-Boundary Layer Interaction Mechanisms, Zane Matthew Shoppell

Masters Theses

Recent work at the University of Tennessee Space Institute has demonstrated that the resonant behavior observed in the spectra of cylinder- and blunt-fin-generated XSBLIs is connected to fundamental fluid mechanisms within the boundary layer. Therefore, a test campaign was conducted to characterize the fundamental mechanisms that drive the low-frequency unsteadiness in cylinder- and blunt-fin-generated shockwave-boundary layer interactions, specifically shockwave-boundary layer interactions in which the incoming boundary layer is undergoing a laminar-to-turbulent transition. This research aims to develop a deeper understanding of such interactions and characterize the resonant behavior observed in past work by varying the sweepback angle of a hemicylindrical …

Quasi 1d Modelling Of A Scramjet Engine Cycle Using Heiser-Pratt Approach, Asmaa Chakir

Theses and Dissertations

Scramjet engines are key for sustained hypersonic flights. Analytic models play a critical role in the preliminary design of a scramjet engine configuration. The objective of this research is to develop and validate a quasi-1D model for the scramjet engine encompassing inlet, isolator and combustor, to evaluate the impact of flight conditions and design parameters on the engine functionality. The model is developed assuming isentropic flow in the inlet with a single turn; modified Fanno-flow equations in the isolator that account for the area change of the core flow; and the combustor is modeled using Heiser-Pratt equations accounting for the …

Upscaling And Development Of Linear Array Focused Laser Differential Interferometry For Simultaneous 1d Velocimetry And Spectral Profiling In High-Speed Flows, Kirk Davenport

Masters Theses

In this research a new configuration of linear array-focused laser differential interferometry (LA-FLDI) is described. This measurement expands on previous implementations of LA-FLDI through the use of an additional Wollaston prism. This additional prism expands the typical single LA-FLDI column into two columns of FLDI point pairs. The additional column of probed locations allows for increased spatial sampling of frequency spectra as well as the addition of simultaneous wall normal velocimetry measurements. The new configuration is used to measure the velocity profile and frequency content across a Mach 2 turbulent boundary layer at six wall normal locations simultaneously. Features of …

The Effect Of Fuel Injector Spacing, Angle, And Blowing Ratio On The Fuel Air Mixing Performance Of A Scramjet Engine, Jonathan R. Copeland

Honors College Theses

In the operation of a Scramjet engine, which operates at hypersonic velocities, one of the most important factors is mixing the fuel and air before the high velocity air stream through the engine blows the mixture out of the engine before it could burn. Because of the importance of rapidly mixing fuel and air within a Scramjet engine, there are multiple design elements used to increase mixing. One of which is called a flame holder cavity, which is usually located behind fuel injectors, and designed with an open (length to depth ratio is less than 10) geometry to promote recirculation …

Analysis On Fuel Options For Scramjet Engines With The Study To Lower The Starting Mach Number, Sumantra Luitel, Gagan Dangi

Honors Theses

The main objectives of this report were to perform analysis of an ideal scramjet engine, to assess the influence of fuel on endurance factor, and the possibility of lowering the starting Mach Number of the scramjet. In the first part, an ideal cycle parametric analysis was conducted on three different fuels i.e. Liquid Hydrogen (LH2), Jet Propellant 7 (JP-7), and Rocket Propellant (RP-1), taking into account their availability, physical properties, current uses, and potential uses. The detailed analysis is done largely relying on a 9 step Parametric Cycle Analysis technique to study how fuel properties influence the variation of seven …

Characterizing The Unsteady Dynamics Of Cylinder-Induced Shock Wave/Transitional Boundary Layer Interactions Using Non-Intrusive Diagnostics, Elizabeth Lara Lash

Doctoral Dissertations

The objectives of this study were to provide time-resolved (1) characterizations of shock wave/transitional boundary layer interactions using schlieren flow visualization, and (2) correlations of unsteady shock motion to boundary layer features. The characteristics of cylinder-induced shock wave/transitional boundary layer interactions in a Mach 2 freestream flowfield were studied experimentally. The Reynolds number in the Mach 2 facility was 30,000,000 m-1. Incoming boundary layers were in transitional and fully turbulent states. Characterizing the shock wave motion was based on tracking the position of the shock wave on the model surface in schlieren images. The motion of the shock waves revealed …

Comparison Of Reynolds-Averaged Navier-Stokes Turbulence Models For Simulating Boundary Layers In Hypersonic Flows, Jorge-Valentino Kurose Bretzke

Masters Theses

“This study describes the use of Computational Fluid Dynamics (CFD) codes to simulate hypersonic boundary layers using several different turbulent closure models and comparing Reynolds-Averaged Navier-Stokes (RANS) simulations against Direct Numerical Simulations (DNS) of similar test cases. The test cases in this study consist of a flat plate in a Mach 8 freestream with a zero pressure gradient and wall recovery ratio of 0.48, as well as a Mach 8 axisymmetric nozzle also with a cold wall. The RANS models used in this study are the Spalart-Allmaras model, Baldwin-Lomax model, Menter K-Omega Baseline and Menter K-Omega Shear Stress Transport models. …

Effect Of Turbulence Model Closure Coefficient Uncertainty On Scramjet Flow Field Analysis, Martin Albert Di Stefano

Doctoral Dissertations

“The numerical modeling of supersonic combustion ramjet (scramjet) engine flow paths plays an important role in the design of hypersonic air-breathing propulsion systems. Due to the complexity of the flow field physics and limited experimental data, numerical models possess uncertainties which should be addressed to improve the prediction accuracy of the simulations. In this study, the effect of turbulence model closure coefficient uncertainty on the Reynolds-averaged Navier-Stokes solution of a scramjet isolator and scramjet strut fuel injector flow field is investigated with an uncertainty quantification and sensitivity analysis study for commonly used turbulence models. Turbulence models considered in this work …

Thermochemical Non-Equilibrium Models For Weakly Ionized Hypersonic Flows With Application To Slender-Body Wakes, Matthew P. Clarey

Theses and Dissertations

The current resurgence of interest in hypersonic technologies has warranted an inquiry into the commonly employed thermochemical non-equilibrium models within computational fluid dynamic (CFD) simulations. Additionally, research has historically focused on forebody flowfields, while studies of the complex wake structure have remained elusive. Although the forebody is of significance for vehicle analysis, the wake presents many exploitative characteristics. This dissertation aimed to address these two deficits. First, two three-temperature non-equilibrium models were developed, increasing the fidelity of hypersonic solutions above that of the legacy two-temperature model. The models were then investigated via zero-dimensional simulations, to detail the non-equilibrium processes, and …

Validation Of Cfd Simulations For Hypersonic Flow Over A Yawed Cone, Julian Cecil

McKelvey School of Engineering Theses & Dissertations

This study aims to numerically simulate the wind tunnel results for hypersonic flow over a circular cone of semi-apex angle of 10 degrees yawed from 0° to 20° using the commercial computational fluid dynamics software ANSYS Fluent. The ANSYS workbench is used to create the 10° semi-apex circular cone with a shock aligned structured mesh of 3.05 million cells surrounding the cone. Simulation boundary conditions for pressure and temperature in the far field correspond to Tracy’s wind tunnel experiment at Cal Tech. The six simulations cases are conducted for yaw angles of 0, 8, 12, 16, 20 and 24 degrees. …

Numerical Simulation Of Heat Transfer And Chemistry In The Wake Behind A Hypersonic Slender Body At Angle Of Attack, Matthew J. Satchell, Jeffrey M. Layng, Robert B. Greendyke

Faculty Publications

The effect of thermal and chemical boundary conditions on the structure and chemical composition of the wake behind a 3D Mach 7 sphere-cone at an angle of attack of 5 degrees and an altitude of roughly 30,000 m is explored. A special emphasis is placed on determining the number density of chemical species which might lead to detection via the electromagnetic spectrum. The use of non-ablating cold-wall, adiabatic, and radiative equilibrium wall boundary conditions are used to simulate extremes in potential thermal protection system designs. Non-ablating, as well as an ablating boundary condition using the “steady-state ablation” assumption to compute …

Improved Modeling Of Atmospheric Entry For Meteors With Nose Radii Between 5cm And 10m, Jakob Dale Brisby

Masters Theses

Atmospheric entry studies typically look closely at the peak heating rate that a body encounters during its trajectory. This is an extremely important phenomenon to study because it allows engineers to determine if a trajectory is possible with given materials and craft design specifications. It also allows designers to choose what type of method will be used for mitigating the enormous heat fluxes during entry. In general, it is accepted that during the super-sonic flight regime the body will continue to be heated and an ablative heat shield often is used to deal with these heating processes. The theory outlined …

High Temperature Flow Solver For Aerothermodynamics Problems, Huaibao Zhang

Theses and Dissertations--Mechanical Engineering

A weakly ionized hypersonic flow solver for the simulation of reentry flow is firstly developed at the University of Kentucky. This code is the fluid dynamics module of known as Kentucky Aerothermodynamics and Thermal Response System (KATS). The solver uses a second-order finite volume approach to solve the laminar Navier– Stokes equations, species mass conservation and energy balance equations for flow in chemical and thermal non-equilibrium state, and a fully implicit first-order backward Euler method for the time integration. The hypersonic flow solver is then extended to account for very low Mach number flow using the preconditioning and switch of …

A Survey Of Gaps, Obstacles, And Technical Challenges For Hypersonic Applications, Timothy Andrew Barber

Masters Theses

The object of this study is to canvas the literature for the purpose of identifying and compiling a list of Gaps, Obstacles, and Technological Challenges in Hypersonic Applications (GOTCHA). The significance of GOTCHA related deficiencies is discussed along with potential solutions, promising approaches, and feasible remedies that may be considered by engineers in pursuit of next generation hypersonic vehicle designs and optimizations. Based on the synthesis of several modern surveys and public reports, a cohesive list is formed, consisting of widely accepted areas needing improvement and falling under several general categories. These include: aerodynamics, propulsion, materials, analytical modeling, CFD modeling, …

Evaluation Of Geometric Scale Effects For Scramjet Isolators, Jaime Enrique Perez

Masters Theses

A numerical analysis was conducted to study the effects of geometrically scaling scramjet inlet-combustor isolators. Three-dimensional fully viscous numerical simulation of the flow inside constant area rectangular ducts, with a downstream back pressure condition, was analyzed using the SolidWorks Flow Simulation software. The baseline, or 1X, isolator configuration has a 1” x 2.67” cross section and 20” length. This baseline configuration was scaled up based on the 1X configuration mass flow to 10X and 100X configurations, with ten and one hundred times the mass flow rate, respectively. The isolator aspect ratio of 2.67 was held constant for all configurations. To …

Numerical Examination Of Flow Field Characteristics And Fabri Choking Of 2d Supersonic Ejectors, Brett G. Morham

Master's Theses

An automated computer simulation of the two-dimensional planar Cal Poly Supersonic Ejector test rig is developed. The purpose of the simulation is to identify the operating conditions which produce the saturated, Fabri choke and Fabri block aerodynamic flow patterns. The effect of primary to secondary stagnation pressure ratio on the efficiency of the ejector operation is measured using the entrainment ratio which is the secondary to primary mass flow ratio.

The primary flow of the ejector is supersonic and the secondary (entrained) stream enters the ejector at various velocities at or below Mach 1. The primary and secondary streams are …

Computational Aerodynamic Analysis Of The Flow Field About A Hypervelocity Test Sled, Andrew J. Lofthouse

Theses and Dissertations

The flow field about the nose section of a hypervelocity test sled is computed using computational fluid dynamics. The numerical model of the test sled corresponds to the Nike O/U narrow gage sled used in the upgrade program at the High Speed Test Track facility, Holloman Air Force Base, New Mexico. The high temperatures and pressures resulting from the aerodynamic heating and loading affect the sled structure and the performance of the vehicle. The sled transitions from an air environment to a helium environment at a speed of approximately 3,300 feet per second (Mach 3 in air, Mach 1.02 in …

Efficient Dynamic Unstructured Methods And Applications For Transonic Flows And Hypersonic Stage Separation, Xiaobing Luo

Mechanical & Aerospace Engineering Theses & Dissertations

Relative-moving boundary problems have a wide variety of applications. They appear in staging during a launch process, store separation from a military aircraft, rotor-stator interaction in turbomachinery, and dynamic aeroelasticity.

The dynamic unstructured technology (DUT) is potentially a strong approach to simulate unsteady flows around relative-moving bodies, by solving time-dependent governing equations. The dual-time stepping scheme is implemented to improve its efficiency while not compromising the accuracy of solutions. The validation of the implicit scheme is performed on a pitching NACA0012 airfoil and a rectangular wing with low reduced frequencies in transonic flows. All the matured accelerating techniques, including the …