Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 6 of 6
Full-Text Articles in Engineering
Characterization Of A Robotic Manipulator For Dynamic Wind Tunnel Applications, James C. Lancaster
Characterization Of A Robotic Manipulator For Dynamic Wind Tunnel Applications, James C. Lancaster
Theses and Dissertations
The newly acquired 6-DOF Motion Test Apparatus (MTA) was installed to perform dynamic wind tunnel testing in the AFIT Low Speed Wind Tunnel. Several complex motions revealed that the overall performance of the test rig needed improvement especially during small motions. The motions exposed that further enhancements would need to be performed individually for each joint. This research effort focused on the improvement of the MTA wrist roll motor and controller using a pitch oscillation. The controller software was improved using position feedback because the MTA wrist roll motor and controller exhibited reduced signal bias and amplitude attenuation. The enhanced …
Experimental Characterization Of Turbulent Flow Around Cylinder Arrays, Adam D. Harder
Experimental Characterization Of Turbulent Flow Around Cylinder Arrays, Adam D. Harder
Theses and Dissertations
This research was done as part of an effort to develop alternative fire suppressant technologies for aircraft engine nacelles. A circular cylinder array was designed, built, and placed in the AFIT roll-around low speed wind tunnel to model generic clutter inside an engine nacelle. A turbulence grid was fabricated to enable measurements of the effects of turbulence level, independent of airspeed, on the flow over different model configurations. The wind tunnel test section was 12 inches wide x 12 inches high x 24 inches long. Pressure differential measurements were taken on various cylinder configurations. The configurations included one cylinder as …
Wind Tunnel Study Of Interference Effects Relating To Aft Supersonic Ejection Of A Store, Timothy P. Jung
Wind Tunnel Study Of Interference Effects Relating To Aft Supersonic Ejection Of A Store, Timothy P. Jung
Theses and Dissertations
An investigation into the issues surrounding the release of a store into a supersonic wake was conducted. A 10-degree half-angle cone was used to model the carrier vehicle as well as the store. The store was 42% than the vehicle. The experiments were conducted at a freestream Mach number of 2.93 and at zero degrees angle of attack. This study analyzed the effects of a support or strut mounted under the wind tunnel model. Research was conducted on the effects of a store at various positions in the wake, as well as the effects of a rear cavity in the …
A New Drag Measurement System For Wind Tunnel Testing Of The Racing Bicycle And Rider To Determine A Low Drag Configuration, Brian A. Parker
A New Drag Measurement System For Wind Tunnel Testing Of The Racing Bicycle And Rider To Determine A Low Drag Configuration, Brian A. Parker
Theses and Dissertations
This study investigated the application of splitter plate effects to reduce the aerodynamic drag of the racing bicycle and rider system. A sensitive, low-force, beam-type, single-component balance was developed to provide drag measurements accurate to within 0.053 N (0.012 lbf). The performance of the new system was verified by comparing the measured drag on a three-dimensioaal, right-circular cylinder model, 0.127 m (5.0 in) in diameter and 0.610 m (24 in) long, with the results from a commercial balance and a other similar data. The bicycle and rider model consisted of a full-scale mannequin comprising only the hips, legs …
The Design And Development Of A Low-Speed, Low-Force Wind Tunnel Data Acquisition System With An Application To Bicycle Front Fork Spacing, Alan W. Elledge
The Design And Development Of A Low-Speed, Low-Force Wind Tunnel Data Acquisition System With An Application To Bicycle Front Fork Spacing, Alan W. Elledge
Theses and Dissertations
This thesis encompassed the design, development, and application of a low-speed, low-force data acquisition system for the AFIT 5-ft Wind Tunnel. The new data acquisition system was designed and developed to measure approximately 0.045 N (about 0.01 lbf) at nearly 64.4 km/h (40 mph). Verification of the capability was obtained through testing of a cylindrical model. As part of a technology transition program with Wright Laboratory, this new system was used to investigate bicycle front fork blade spacing in order to determine the optimal spacing for minimum drag. As for the minimum drag of a bicycle with an …
A Study Of A Wind Tunnel Measurement System For Unsteady Pressures Using Pneumatic Transmission Lines, Mohammed Javed Khan
A Study Of A Wind Tunnel Measurement System For Unsteady Pressures Using Pneumatic Transmission Lines, Mohammed Javed Khan
Theses and Dissertations
The application of pneumatic transmission lines theory to a tube-scanning valve system for unsteady pressure measurements in the AFIT 5-foot wind tunnel is investigated. Transfer gains of various tube-scanning valve configurations were experimentally measured and the validity of a theoretical model verified for a frequency range of 20 Hz to 140 Hz. The selected system having a 0.0625-in. ID flexible tube of 84 in. length connected to a scanning valve was installed in the wind tunnel. Unsteady pressures introduced over an 18 percent airfoil at zero angle of attack were measured with this system. Data were collected for 0, 40, …