American Studies Commons^™

Reconfigurable Antenna And Rf Circuits Using Multi-Layer Stretchable Conductors, Riaz Ahmed -. Liyakath

USF Tampa Graduate Theses and Dissertations

The growth of flexible electronics industry has given rise to light-weight, flexible devices which have a wide range of applications such as wearable electronics, flexible sensors, conformal antennas, bio-medical applications, solar cells etc. Though several techniques exist to fabricate flexible devices, the limiting factors have been durability, cost and complexity of the approach. In this research, the focus has been on developing stretchable (flexible) conductors using a multi-layer structure of metal and conductive rubber. The stretchable conductors developed using this approach do not lose electrical connection when subjected to large strains up to 25%. Also, the conductivity of the conductive …

Implementation And Optimization Of An Inverse Photoemission Spectroscopy Setup, Ervin Gina

USF Tampa Graduate Theses and Dissertations

Inverse photoemission spectroscopy (IPES) is utilized for determining the unoccupied electron states of materials. It is a complementary technique to the widely used photoemission spectroscopy (PES) as it analyzes what PES cannot, the states above the Fermi energy. This method is essential to investigating the structure of a solid and its states. IPES has a broad range of uses and is only recently being utilized.

This thesis describes the setup, calibration and operation of an IPES experiment. The IPES setup consists of an electron gun which emits electrons towards a sample, where photons are released, which are measured in isochromat …

Novel Encapsulation Of Oxidizer Applied To Galvanic Cells: Aluminum / H2o2 Galvanic Cell As A Case Study, Marlyn Colon

USF Tampa Graduate Theses and Dissertations

The work presented in this thesis aims to address the obstacles that side reactions create in aluminum / H2O2 galvanic cells by proposing to control the cathodic reactant, H2O2, via encapsulation. Encapsulation of the cathodic reactant is achieved utilizing a non-ionic surfactant vesicle (i.e. niosome). Once encapsulated, a second control element over the cathodic reactant is provided. The use of a polymer will be implemented to achieve stability and render further control over the encapsulated H2O2 solution. Implementation of the proposed novel cathodic control system in aluminum / H2O2 galvanic cells aims to minimize aluminum consumption and increase cell efficiency. …

Respiratory Monitoring System Based On The Thoracic Expansion Measurement, Fabiola Araujo Cespedes

USF Tampa Graduate Theses and Dissertations

The purpose of this reasearch was to develop a respiratory monitoring system using a reflective object sensor based belt to measure the thoracic expansion of a neonatal for future application at the medical center of the Universidad Evangelica Boliviana (UEB). This medical center, being founded by the UEB University, is dedicated to help and serve the poor and currently has no respiratory monitoring system.

The methodology used was first to build and test the respiratory sensor belt and test the relationship between the blet expansion and the voltage generated. The, to incorporate the respiratory sensor belt in a system that …

The Electronic Structure Of Biomolecular Self-Assembled Monolayers, Matthaeus Anton Wolak

USF Tampa Graduate Theses and Dissertations

The studies presented here address the characterization of the electronic structure of various self-assembled monolayers (SAMs) of peptide nucleic acid (PNA) and tetraphenylporphyrin (TPP) SAMs and arrays, formed on gold substrates.

PNA is a promising alternative to DNA for bio-sensing applications, as well as for strategies for self-assembly based on nucleic acid hybridization. In recent years charge transfer through PNA molecules was a focus of research due to possible applications in self-assembled molecular circuits and molecular tools. In light of this research it is interesting to investigate the electronic structure of PNA interfaces to gold, a potential electrode material.

TPP …

Analysis And Optimization Of Broadband Measurement Cells For The Characterization Of Dielectric Polymer Films, Scott Skidmore

USF Tampa Graduate Theses and Dissertations

The current techniques and methodologies used in the field of material characterization are well documented and widely accepted as reliable and accurate. However, literature describing these techniques focuses on the algorithms used during material characterization; few studies have reposted on the design of, and the selection criteria for, the test fixtures themselves. This research focuses on the measurement cell with the goal of determining the sensitivity of the measurement cell to the addition of a thin film material.

Microstrip and coplanar waveguide were chosen for the analysis, which included three configurations of each transmission line geometry: a reference with no …

Optimization Of Bio-Impedance Sensor For Enhanced Detection And Characterization Of Adherent Cells, Dorielle T. Price

USF Tampa Graduate Theses and Dissertations

This research focuses on the detection and characterization of cells using

impedance-based techniques to understand the behavior and response of cells to internal/environmental changes. In combination with impedimetric sensing techniques, the biosensors in this work allow rapid, label-free, quantitative measurements and are very sensitive to changes in environment and cell morphology. The biosensor design and measurement setup is optimized to detect and differentiate cancer cells and healthy (normal) cells. The outcome of this work will provide a foundation for enhanced 3-dimensional tumor analysis and characterization; thus creating an avenue for earlier cancer detection and reduced healthcare costs.

The magnitude of …

Design Issues In Magnetic Field Coupled Array: Clock Structure, Fabrication Defects And Dipolar Coupling, Anita Kumari

USF Tampa Graduate Theses and Dissertations

Even though silicon technology is dominant today, the physics (quantum electron tunneling effect), design (power dissipation, wire delays) and the manufacturing (lithography resolution) limitations of CMOS technology are pushed towards the scaling end. These issues motivated us towards a new paradigm that contributes to a continued advancement in terms of performance, density, and cost. The magnetic field coupled computing (MFC) paradigm, which is one of the regimes where we leverage and utilize the neighbor interaction of the nanomagnets to order the single-domain magnetic cells to perform computational tasks. The most important and attractive features of this technology are: 1) room …

Approaches To Arc Flash Hazard Mitigation In 600 Volt Power Systems, Curtis Thomas Latzo

USF Tampa Graduate Theses and Dissertations

Federal regulations have recognized that arc flash hazards are a critical source of potential injury. As a consequence, in order to work on some electrical equipment, the energy source must be completely shut-down. However, power distribution systems in mission critical facilities such as hospitals and data centers must sometimes remain energized while being maintained. In recent years the Arc Flash Hazard Analysis has emerged as a power system tool that informs the qualified technician of the incident energy at the equipment to be maintained and recommends the proper protective equipment to wear. Due to codes, standards and historically acceptable design …

Stress-Strain Management Of Heteroepitaxial Polycrystalline Silicon Carbide Films, Christopher William Locke

USF Tampa Graduate Theses and Dissertations

Silicon carbide (SiC) is one of the hardest known materials and is also, by good fortune, a wide bandgap semiconductor. While the application of SiC for high-temperature and high-power electronics is fairly well known, its utility as a highly robust, chemically-inert material for microelectrical mechanical systems (MEMS) is only beginning to be well recognized. SiC can be grown on both native SiC substrates or on Si using heteroepitaxial growth methods which affords the possibility to use Si micromachining methods to fabricate advanced SiC MEMS devices.

The control of film stress in heteroepitaxial silicon carbide films grown on polysilicon-on-oxide substrates has …

Characterizing Wireless And Powerline Communication Channels With Applications To Smart Grid Networks, Sabih Guzelgoz

USF Tampa Graduate Theses and Dissertations

Smart grid aims at improving the efficiency, reliability, security, and quality of service (QoS) of the current electricity grid by exploiting the advances in communication and information technology. In parallel to size of the electricity grid, smart grid communication infrastructure should cover a very large geographical area that may extend from remote generation sites to densely populated residential regions and inside buildings, homes, and electricity-power-system environments. In such an extensive communication network, different communication technologies operating on different communication medium are likely to coexist. Among the communication technologies available, wireless and power line communication (PLC) based solutions are comparatively attractive …

Diamond Based-Materials: Synthesis, Characterization And Applications, Qiang Hu

USF Tampa Graduate Theses and Dissertations

The studies covered in this dissertation concentrate on the various forms of diamond films synthesized by chemical vapor deposition (CVD) method, including microwave CVD and hot filament CVD. According to crystallinity and grain size, a variety of diamond forms primarily including microcrystalline (most commonly referred to as polycrystalline) and nanocrystalline diamond films, diamond-like carbon (DLC) films were successfully synthesized. The as-grown diamond films were optimized by changing deposition pressure, volume of reactant gas hydrogen (H2) and carrier gas argon (Ar) in order to get high-quality diamond films with a smooth surface, low roughness, preferred growth orientation and high sp3 bond …

Resource Allocation Methodologies With Fractional Reuse Partitioning In Cellular Networks, Hazar Aki

USF Tampa Graduate Theses and Dissertations

Conventional cellular systems have not taken full advantage of fractional frequency reuse and adaptive allocation due to the fixed cluster size and uniformed channel assignment procedures. This problem may cause more fatal consequences considering the cutting-edge 4G standards which have higher data rate requirements such as 3GPP-LTE and IEEE 802.16m (WiMAX). In this thesis, three different partitioning schemes for adaptive clustering with fractional frequency reuse were proposed and investigated. An overlaid cellular clustering scheme which uses adaptive fractional frequency reuse factors would provide a better end-user experience by exploiting the high level of signal to interference ratio (SIR). The proposed …

Log-Periodic Microstrip Patch Antenna Miniaturization Using Artificial Magnetic Conductor Surfaces, Ahmad Tariq Almutawa

USF Tampa Graduate Theses and Dissertations

Microstrip patch antennas are attractive for numerous military and commercial applications due to their advantages in terms of low-profile, broadside radiation, lowcost, low-weight and conformability. However, the inherent narrowband performance of patch antennas prohibits their use in systems that demand wideband radiation. To alleviate the issue, an existing approach is to combine multiple patch antennas within a log-periodic array configuration [1]. These log-periodic patch antennas (LPMAs) are capable of providing large bandwidths (>50%) with stable broadside radiation patterns. However, they suffer from electrically large sizes. Therefore, their miniaturization without degrading the bandwidth performance holds promise for extending their use …

Novel Film Formation Pathways For Cu2znsnse4 For Solar Cell Applications, Sree Satya Kanth Bendapudi

USF Tampa Graduate Theses and Dissertations

Because of the anticipated high demand for Indium, ongoing growth of CIGS technology may be limited. Kesterite materials, which replace In with a Zn/Sn couple, are thought to be a solution to this issue. However, efficiencies are still below the 10% level, and these materials are proving to be complex. Even determination of the bandgap is not settled because of the occurrence of secondary phases. We use a film growth process, 2SSS, which we believe helps control the formation of secondary phases. Under the right growth conditions we find 1/1 Zn/Sn ratios and XRD signatures for Cu2ZnSnSe4 with no evidence …

Ultra-Low Power Electronics For Autonomous Micro-Sensor Applications, Rebeka Davidova

USF Tampa Graduate Theses and Dissertations

This thesis presented the research, design and fabrication associated with a unique application of rectenna technology combined with lock-in amplification. An extremely low-power harmonic transponder is conjoined with an interrogator base-station, and utilizing coherent demodulation the Remote Lock-In Amplifier (RLIA) concept is realized. Utilizing harmonic re-radiation with very low-power input, the 1^st generation transponder detects a transmitted interrogation signal and responds by retransmitting the second harmonic of the signal. The 1^st generation transponder performs this task while using no additional power besides that which accompanies the wireless signal. Demonstration of the first complete configuration provided proof of concept …

Smart Grid Functionality Of A Pv-Energy Storage System, Nenad Damnjanovic

USF Tampa Graduate Theses and Dissertations

Renewable Energy will be the key to preserving the Earth's remaining resources and continuing this surge of technological progress that we have experienced this past century. New philosophies of how/when/where energy should be consumed and produced are attempting to improve upon the current grid infrastructure. The massive advancement in communications, renewable and control systems will allow this new-age electric grid to maximize its efficiency while reducing cost. Renewable, "green" energy is now at the forefront of innovation. As the world population increases, there will be a need to free ourselves from natural resources as much as possible. Advanced Energy Storage …

Cdte/Cds Thin Film Solar Cells Fabricated On Flexible Substrates, Vasilios Palekis

USF Tampa Graduate Theses and Dissertations

Cadmium Telluride (CdTe) is a leading thin film photovoltaic (PV) material due to its near ideal bandgap of 1.45 eV and its high optical absorption coefficient. The typical CdTe thin film solar cell is of the superstrate configuration where a window layer (CdS), the absorber (CdTe) and a back contact are deposited onto glass coated with a transparent electrode.

Substrate CdTe solar cells where the above listed films are deposited in reverse are not common. In this study substrate CdTe solar cells are fabricated on flexible foils.

The properties of the Molybdenum back contact, Zinc Telluride (ZnTe) interlayer and CdTe …

Guiding Electric Fields For Electroporation Applications, Jose Rey

USF Tampa Graduate Theses and Dissertations

Electroporation is the critical step in an electric field mediated drug or gene delivery protocol. Electroporation based protocols have been successfully demonstrated in cancer clinical trials, however, its impact in other applications is still under investigation. A significant roadblock to long term functioning of implantable biosensors in vivo is the tissue reaction in the form of fibrous encapsulation that results in reduced transport to the sensing element of the biosensor. In vivo gene electroporation has a great potential as a means to modify the transport properties of tissues in the proximity of the sensing element of implantable biosensors.

This dissertation …

Atrial Fibrillation Signal Analysis, Raja Sarath Chandra Prasad Vaizurs

USF Tampa Graduate Theses and Dissertations

Atrial fibrillation (AF) is the most common type of cardiac arrhythmia encountered in clinical practice and is associated with an increased mortality and morbidity. Identification of the sources of AF has been a goal of researchers for over 20 years. Current treatment procedures such as Cardio version, Radio Frequency Ablation, and multiple drugs have reduced the incidence of AF. Nevertheless, the success rate of these treatments is only 35-40% of the AF patients as they have limited effect in maintaining the patient in normal sinus rhythm. The problem stems from the fact that there are no methods developed to analyze …

Fabrication And Characterization Of Electrospun Cactus Mucilage Nanofibers, Yanay Pais

USF Tampa Graduate Theses and Dissertations

This work seeks to fabricate, optimize, and characterize nanofibers of cactus Opuntia ficus-indica mucilage and Poly (vinyl alcohol) (PVA) by electrospinning. Mucilage is a neutral mixture of sugars produced by cactus and PVA is a non-toxic, water-soluble, synthetic polymer, which is widely used as a co-spinning agent for polymers. Mucilage was extracted from the cactus pad and prepared for electrospinning by mixing with acetic acid. Two types of PVA were used differentiating in high and low molecular weights. Concentrations of PVA were varied to find an adequate threshold for fiber formation. Changing the ratio of PVA to cactus mucilage produced …

Molybdenum Nitride Films In The Back Contact Structure Of Flexible Substrate Cdte Solar Cells, Vasudha Guntur

USF Tampa Graduate Theses and Dissertations

CdTe solar cells in the superstrate configuration have achieved record efficiencies of 16% but those in the substrate configuration have reached efficiencies of only 7.8%. A major reason for the lower efficiency of substrate CdTe solar cells is the poor back contact. In this work, CdTe solar cells of the substrate configuration have been fabricated on flexible metallic substrates. For this type of devices, impurity diffusion out of stainless-steel substrates due to high temperature processing can be a cause for poor cell performance. It is necessary to investigate ways of improving the back contact by trying to mitigate the above …

Fabrication And Characterization Of Novel 2sss Cigs Thin Film Solar Cells For Large-Scale Manufacturing, Keshavanand Jayadevan

USF Tampa Graduate Theses and Dissertations

A novel 2SSS (2 Step Solid Selenization) CIGS (Cu, In, Ga, Se) thin film solar cell recipe was developed which can be a replacement to the conventional co-deposition process usually employed for large-scale manufacturing. The co-deposition procedure is faced with multiple problems such as selenium incorporation, effective gallium incorporation in the absorber. It is a 2-step proprietary procedure with better control over growth mechanisms and material utilization for the absorber layer for the CIGS thin film solar cells. It makes use of solid selenium source as preferred by manufacturers. Each step of the 2-step procedure was dealt with separately for …

Performance Enhancement Using Cross Layer Approaches In Wireless Ad Hoc Networks, Murad Khallid

USF Tampa Graduate Theses and Dissertations

Ad hoc network is intrinsically autonomous and self-configuring network that does not require any dedicated centralized management. For specialized applications such as, military operations, search-and-rescue missions, security and surveillance, patient monitoring, hazardous material monitoring, 4G (4th Generation) coverage extension, and rural communication; ad hoc networks provide an intelligent, robust, flexible and costeffective solution for the wireless communication needs.

As in centralized wireless systems, ad hoc networks are also expected to support high data rates, low delays, and large node density in addition to many other QoS (Quality of Service) requirements. However, due to unique ad hoc network characteristics, spectrum scarcity, …

Magneto-Dielectric Polymer Nanocomposite Engineered Substrate For Rf And Microwave Antennas, Cesar A. Morales

USF Tampa Graduate Theses and Dissertations

This dissertation presents the first reported systematic investigation on the implementation of multilayer patch antennas over Fe3O4-based polymer nanocomposite (PNC) magneto-dielectric substrates. The PNC substrate is created by the monodispersion of Fe3O4 nanopthesiss, with mean size of 7.5nm, in a polymeric matrix of Polydimethylsiloxane (PDMS).

Recently, magneto-dielectric substrates have been proposed by several researchers as a means for decreasing the size and increasing the bandwidth of planar antennas. Nevertheless, factors such as high loss and diminished control over magnetic and dielectric properties have hindered the optimal performance of antennas. In addition, the incompatibility and elevated complexity prevents integration of conventional …

Advanced Signal Processing Techniques For Single Trial Electroencephalography Signal Classification For Brain Computer Interface Applications, Kun Li

USF Tampa Graduate Theses and Dissertations

Brain Computer Interface (BCI) is a direct communication channel between brain and computer. It allows the users to control the environment without the need to control muscle activity [1-2]. P300-Speller is a well known and widely used BCI system that was developed by Farwell and Donchin in 1988 [3]. The accuracy level of the P300-BCI Speller as measured by the percent of communicated characters correctly identified by the system depends on the ability to detect the P300 event related potential (ERP) component among the ongoing electroencephalography (EEG) signal. Different techniques have been tested to reduce the number of trials needed …

Linear And Nonlinear Control Of Unmanned Rotorcraft, Ioannis A. Raptis

USF Tampa Graduate Theses and Dissertations

The main characteristic attribute of the rotorcraft is the use of rotary wings to produce the thrust force necessary for motion. Therefore, rotorcraft have an advantage relative to fixed wing aircraft because they do not require any relative velocity to produce aerodynamic forces. Rotorcraft have been used in a wide range of missions of civilian and military applications. Particular interest has been concentrated in applications related to search and rescue in environments that impose restrictions to human presence and interference.

The main representative of the rotorcraft family is the helicopter. Small scale helicopters retain all the flight characteristics and physical …

Smart Grid Reliability Assessment Under Variable Weather Conditions, Arif Islam

USF Tampa Graduate Theses and Dissertations

The needs of contemporary electric utility customers and expectations regarding energy supply require dramatic changes in the way energy is transmitted and delivered. A smart grid is a concept by which the existing and aging electrical grid infrastructure is being upgraded with integration of multiple applications and technologies; such as two way power transfer, two way communication, renewable distributed generation, automated sensors, automated & advanced controls, central control, forecasting system and microgrids. This enables the grid to be more secure, reliable, efficient, self-healing, while reducing greenhouse gases. In addition, it will provide new products & services and fully optimize asset …

Advanced Transceiver Algorithms For Ofdm(A) Systems, Hisham A. Mahmoud

USF Tampa Graduate Theses and Dissertations

With the increasing advancements in the digital technology, future wireless systems are promising to support higher data rates, higher mobile speeds, and wider coverage areas, among other features. While further technological developments allow systems to support higher computational complexity, lower power consumption, and employ larger memory units, other resources remain limited. One such resource, which is of great importance to wireless systems, is the available spectrum for radio communications. To be able to support high data rate wireless applications, there is a need for larger bandwidths in the spectrum. Since the spectrum cannot be expanded, studies have been concerned with …

A Platform For Research On Localization And Tracking Using Wireless Sensor Networks, Sai Kiran Rupanagudi

USF Tampa Graduate Theses and Dissertations

This research proposed the integration of wireless sensor networks, a mobile platform and a fixed station for the development of a test bed system to conduct research on localization, tracking, navigation and network mapping. The overall integrated system acts as a basis for future research on localization of wireless nodes in an indoor environment. The system enables the transfer of information from the sensor node on the platform to a distant computer through wireless communication. In addition, a robotic platform is proposed that uses the developed integrated system as well as other potential applications. The user interface to the system …