Construction Engineering Commons^™

Nasa, Boeing, And Defense Activities: For The Use Of Geopolymers For Space Construction, Terrance E. Bisnauth, Julio Martinez, Saim Wasim

Publications and Research

Good day readers. And with the rate at which our planet earth is being destroyed due to climate change and other catastrophe. That has created serious peril. Food shortages would soon be manifested. So it is wise for us being homosapiens occupy other places to live. And for this to be successful materials would play a significant role for housing us. One of which are Geopolymers.

Investigating Project Success Factors In Post-Disaster Rebuilding Efforts In Nyc, Aalaa Mohammed, Jude R. Vallon, Calvin O. Walters Jr.

Publications and Research

On October 29, 2012, Superstorm Sandy caused nearly $19 billion in damages in New York City including damage to 69,000 residential units. A precipitated amount of roughly $4.2 billion in Community Development Block Grant was allocated towards PDR construction. These funds addressed a range of needs, including rebuilding and rehabilitating housing, assisting displaced tenants, and providing aid to businesses. Post-Disaster Rebuilding (PDR) is similar to construction in the modification of an existing facility that involves either renovation, additions, or subtractions to scopes of work to assist the overall performance of the facility. However, PDR goes further in a highly coordinated …

Higher Sound Levels In K-12 Classrooms Correlate To Lower Math Achievement Scores, Laura Caroline Brill, Lily M. Wang

Durham School of Architectural Engineering and Construction: Faculty Publications

Sound levels from occupied classrooms have been gathered from 220 classrooms across four grade levels (3, 5, 8 and 11) over six school days each and processed with k-means clustering into speech and non-speech clusters. Three metrics describing the classroom acoustics, including the average daily A-weighted equivalent level for non-speech, the average daily difference between the A-weighted equivalent levels for speech and nonspeech (a signal to noise ratio), and the mid-frequency averaged reverberation time, were analyzed against classroom-aggregated standardized reading and math achievement test scores, while controlling for classroom demographics including socioeconomic status. Interactions between the metrics and demographics were …

The Effects Of The Visual Environment On K-12 Student Achievement, Michael Kuhlenengel, Iason Konstantzos, Clarence E. Waters

Durham School of Architectural Engineering and Construction: Faculty Publications

The varying indoor environments among educational buildings can have an impact on students’ ability to learn. This study looks at field data from 220 classrooms in the Midwest, United States, over a two-year period, to analyze the effects of the visual environment on student achievement. The visual environmental metrics considered within this scope include the three new view metrics introduced within the EN 17037 “Daylight of Buildings” standard (Horizontal Sight Angle, Outside Distance of View, and Number of View Layers), as well as standard daylight and electric lighting metrics, focusing on light availability and glare. To capture student achievement, math …

Simulation For A Mems-Based Ctrnn Ultra-Low Power Implementation Of Human Activity Recognition, Muhammad Emad-Ud-Din, Mohammad H. Hasan, Roozbeh Jafari, Siavash Pourkamali, Fadi M. Alsaleem

Durham School of Architectural Engineering and Construction: Faculty Publications

This paper presents an energy-efficient classification framework that performs human activity recognition (HAR). Typically, HAR classification tasks require a computational platform that includes a processor and memory along with sensors and their interfaces, all of which consume significant power. The presented framework employs microelectromechanical systems (MEMS) based Continuous Time Recurrent Neural Network (CTRNN) to performHAR tasks very efficiently. In a real physical implementation, we show that the MEMS-CTRNN nodes can perform computing while consuming power on a nano-watts scale compared to the micro-watts state-of-the-art hardware. We also confirm that this huge power reduction doesn’t come at the expense of reduced …

A Proposal To Harmonize Bim And Iot Data Silos Using Blockchain Application, Zulkefly Abu Bakar, Malachy Mathews Dr

Conference papers

The integration of Building Information Modelling (BIM) and Internet of Things (IoT) provide significant end-to-end benefits for the architecture, engineering, construction, and operations (AECO) industry. Example applications include on-site assembly services, data localization for built environment, occupancy performance measures and many other analyses that can be used to improve the built environment. However, silos in the BIM and IoT data exchange have impacted the digital process adoption in AECO industry, which aims to change the dynamics and behaviors of the current working process. Penzes, (2018) in his report, acknowledges the AECO industry as one of the most fragmented sectors with …

Framework To Develop Time- And Voltage-Dependent Building Load Profiles Using Polynomial Load Models, Andrew Parker, Mhd Anas Alkrch, Kevin James, Ahmad Almaghrebi, Mahmoud Alahmad

Durham School of Architectural Engineering and Construction: Faculty Publications

The power consumption of buildings over the course of each minute, hour, day and season plays a major role in how this load influences the Electric Power System voltage and frequency, and vice versa. This consumption is based on the building's load component types, efficiencies, and how they consume power and react to changes in real time. Due to this complexity, standard full-building load models are typically voltage-invariant. This paper proposes a novel framework to transform these voltage-invariant building load models into fully time- and voltage-dependent load profiles using available data on the voltage sensitivity of individual load components. While …

A Case Study To Quantify Variability In Building Load Profiles, Andrew Parker, Sam Moayedi, Kevin James, Dongming Peng, Mahmoud Alahmad

Durham School of Architectural Engineering and Construction: Faculty Publications

Recent technology development and penetration of advanced metering infrastructure (AMI), advanced building control systems, and the internet-of-things (IoT) in the built environment are providing detailed information on building operation, performance, and user's comfort and behavior. Building owners can obtain a wide range of energy consumption details at various levels of time granularity to augment their decisions as they manage the building operation and interact with the grid. AMI data are providing a new level of detail and visibility that may enhance building services and assets in the smart grid domain and make buildings inch closer to becoming a grid-interactive energy …

Introduction To Prefabrication And Automation In Construction, Luciana Debs, Jiansong Zhang, Yunfeng Chen

School of Construction Management Technology Open Educational Resources

New developments and recent advances in construction methods have the potential to change the future of the architecture, engineering and construction industry. Prefabrication, along with modular construction, provides a safe and controlled environment for the production of building construction elements and raises the need for improved collaboration and coordination from design to manufacturing and from transportation to final assembly. Prefabrication also provides relief from the skilled construction labor shortage while opening up new opportunities for mass customization within the building industry. Prefabrication and modular construction automation are emerging expansion routes for the construction industry. In addition, integral to developing the …

Digital Construction And Bim Research In Ireland 2016-2020, Barry Mcauley, Roger P. West, Alan V. Hore

Conference papers

As the construction industry opens up post pandemic, new and significant challenges will demand considerable expertise, not least in financial viability, solving the housing crisis and facing the very significant climate change pressures to make the industry less wasteful and less carbon intensive. This presents an excellent opportunity to further inculcate aspects of lean construction, particularly BIM into many aspects of construction not traditionally associated with digital construction, provided the necessary expertise is available and known to exist. Following a well-received recent conference paper summarising BIM-related research published by academics in Ireland’s higher education institutions in 2020, this paper will …

Evaluating Prediction Models Of Creep And Drying Shrinkage Of Self-Consolidating Concrete Containing Supplementary Cementitious Materials/Fillers, Micheal Asaad, George Morcous

Durham School of Architectural Engineering and Construction: Faculty Publications

Supplementary cementitious materials (SCMs) and fillers play an important role in enhancing the mechanical properties and durability of concrete. SCMs and fillers are commonly used in self-consolidating concrete (SCC) mixtures to also enhance their rheological properties. However, these additives could have significant effects on the viscoelastic properties of concrete. Existing models for predicting creep and drying shrinkage of concrete do not consider the effect of SCM/filler on the predicted values. This study evaluates existing creep and drying shrinkage models, including AASHTO LRFD, ACI209, CEB-FIP MC90-99, B3, and GL2000, for SCC mixtures with different SCMs/fillers. Forty SCC mixtures were proportioned for …

Designing Gfrp-Reinforced Tilt-Up Wall Panels, Fray F. Pozo-Lora, Marc Maguire

Durham School of Architectural Engineering and Construction: Faculty Publications

Tilt-up construction was effectively enabled on a wide scale in 1979, when the ACI committee 551 report on Tilt-up construction was published, the Recommended Tilt-Up Wall Design, aka, the Yellow Book and the subsequent ACI-SEASC Task, aka the Green Book, and another Tilt-up design and construction manual developed by the ACI in 1988. The Tilt-up Concrete Association was created in 1986 by a group of industry professionals who had the need of an organization dedicated to the industry. ACI 551 maintains a document outlining the standard practice for contemporary Tilt-up design and construction. The ACI 551 document does not consider …

The Facility Infection Risk Estimator™: A Web Application Tool For Comparing Indoor Risk Mitigation Strategies By Estimating Airborne Transmission Risk, Marcel Harmon, Josephine Lau

Durham School of Architectural Engineering and Construction: Faculty Publications

The COVID-19 pandemic created needs for (a) estimating the existing airborne risk of infection from SARS-CoV-2 in existing facilities and new designs and (b) estimating and comparing the impacts of engineering and behavioural strategies for contextually reducing that risk. This paper presents the development of a web application to meet these needs, the Facility Infection Risk Estimator™, and its underlying Wells–Riley based model. The model specifically estimates (a) the removal efficiencies of various settling, ventilation, filtration and virus inactivation strategies and (b) the associated probability of infection, given the room physical parameters and number of individuals infected present with either …

Performance Evaluation Of A Prestressed Belitic Calcium Sulfoaluminate Cement (Bcsa) Concrete Bridge Girder, Nick Markosian, Raed Tawadrous, Mohammad Mastali, Robert J. Thomas, Marc Maguire

Durham School of Architectural Engineering and Construction: Faculty Publications

Belitic calcium sulfoaluminate (BCSA) cement is a sustainable alternative to Portland cement that offers rapid setting characteristics that could accelerate throughput in precast concrete operations. BCSA cements have lower carbon footprint, embodied energy, and natural resource consumption than Portland cement. However, these benefits are not often utilized in structural members due to lack of specifications and perceived logistical challenges. This paper evaluates the performance of a full-scale precast, prestressed voided deck slab bridge girder made with BCSA cement concrete. The rapid-set properties of BCSA cement allowed the initial concrete compressive strength to reach the required 4300 psi release strength at …

Discrete Rigid Block Analysis To Assess Settlement Induced Damage In Unreinforced Masonry Façades, Ryan Ehresman, Nathan Taylor, Bora Pulatsu, Ece Erdogmus

Durham School of Architectural Engineering and Construction: Faculty Publications

In this study, a system of discontinuous rigid blocks is employed to simulate the possible damage mechanisms in unreinforced masonry (URM) façades and load-bearing frame systems subjected to settlement using the discrete element method (DEM). First, the employed modeling strategy is validated utilizing the available experimental results presented in the literature. Once there is a good agreement between the computational models and experimental findings, a sensitivity analysis is performed to quantify the influence of the input parameters defined in the DEM-based numerical model. Finally, the proposed modeling strategy is further utilized to assess the damage pattern that may develop in …

A Comparison Between Ultrasonic Guidedwave Leakage And Half-Cell Potential Methods In Detection Of Corrosion In Reinforced Concrete Decks, Ahmad Shoaib Amiri, Ece Erdogmus, Dana Richter-Egger

Durham School of Architectural Engineering and Construction: Faculty Publications

This article presents the advantages and limitations of a recently developed Ultrasonic Guided Wave Leakage (UGWL) method in comparison to the well-known Half-Cell Potential (HCP) method in their ability to detect corrosion in reinforced concrete (RC) bridge decks. This research also establishes a correlation between UGWL data and chloride content in concrete RC slabs. Concrete slabs submerged in a 10% NaCl solution were monitored using both methods over a period of six months. The chloride content from the three cores (0.84, 0.55, and 0.18%) extracted from the slab after the 6-month long process all exceeded the chloride threshold values suggested …

Understanding Time, Cost, Quality, And Risk Trade-Off In Construction Projects Through A Review Of Literature & Survey Distribution, Aalaa Mohammed

Publications and Research

In the construction industry, projects consist of many different variables that affect successful completion. These variables may be scope, cost, time, quality, risk management and assessment, and more. Although all factors affect various construction projects differently, the three main variables that often result in a need for a trade-off decision are cost, quality, and time. Often referred to as the “Iron Triangle” or the “Triple Constraint”, many times owners and project managers are put under the pressure of having to choose two out of the three variables. If the project is cheap, it cannot be completed quickly and be of …

On The Computational Efficiency Of Les And Hybrid Rans-Les Models In Building Aerodynamics, Aly Mousaad Aly, Faiaz Khaled

Faculty Publications

Large-eddy simulation (LES) has proven to offer superior accuracy in regards to predicting surface pressures compared to the Reynolds-averaged Navier Stokes (RANS) models. However, the primary impediment is the high computational cost associated with LES. The authors attempt to investigate the computational cost and accuracy by employing different sub-grid scale (SGS) models in LES and hybrid RANS-LES models. One of the prerequisites of accurate pressure estimations is to ensure a horizontally homogeneous empty computational domain. This study aims to compare the computational competence qualitatively and quantitatively using an empty domain in regards to the ability to maintain horizontal homogeneity. The …

On The Computational Efficiency Of Les And Hybrid Rans-Les Models In Building Aerodynamics, Faiaz Khaled, Aly Mousaad Aly

Faculty Publications

No abstract provided.

Facilitating The Industrial Sector's Adoption Of Collaborative Project Delivery Methods, Xavier Wood-Aliberch

Durham School of Architectural Engineering and Construction: Dissertations, Thesis, and Student Research

In an effort to improve outcomes in the civil and healthcare sectors, clients have adopted collaborative project delivery methods for the delivery of their capital projects. The success stories in these sectors have gathered the attention of clients in the industrial sector, where cost and schedule overruns have become the norm. The central objective of this thesis is to help clients make the transition to this new type of project delivery.

This thesis was written in a three-paper format, where each paper addresses a challenge with the adoption of collaborative delivery methods. The first paper investigates what type of industrial …

Underground Construction And Space Utilization: A Bibliometric Analysis, Mugdha Praveen Kshirsagar Mrs, Sanjay Kantrao Kulkarni Dr, Nilesh Vedprakash Arora Mr, Devesh Dinesh Maheshwari Mr, Ankush Kumar Meena Mr

Library Philosophy and Practice (e-journal)

Land use optimization is a major concern as the world's population grows at an exponential rate. Surface land is already being depleted at an alarming pace. As a result, buildings can be constructed safely underground, allowing for more productive land use. The primary goal of this paper is to perform a bibliometric review of the literature related to Underground Construction in order to determine the growth of Underground Construction as a method of energy or land optimization in recent years. Between 1975 and 2020 is the time span considered for this survey. The results of the Scopus database are the …

A Hermeneutic Phenomenological Study Into The Impact Of Bim On The Social Dynamics Of The Aec Professional In The Workplace., Malachy Mathews Dr.

Doctoral

A review of the literature published surrounding new digital design and construction technologies and associated processes described within the Architecture, Engineering, and Construction (AEC) community as Building Information Modelling (BIM) or Virtual Design and Construction (VDC) reveals a gap in the theoretical understanding of the impact these technologies are having on professionals who work in this industry. The central aim of this research is to discover if there has been a shift in social dynamics as a result of the adoption of BIM in the workplace and, if there has been, to discuss the meaning of this for the industry …

Exploiting Pull-In/Pull-Out Hysteresis In Electrostatic Mems Sensor Networks To Realize A Novel Sensing Continuous-Time Recurrent Neural Network, Mohammad H. Hasan, Amin Abbasalipour, Hamed Nikfarjam, Siavash Pourkamali, Muhammad Emad-Un-Din, Roozbeh Jafari, Fadi Alsaleem

Durham School of Architectural Engineering and Construction: Faculty Publications

The goal of this paper is to provide a novel computing approach that can be used to reduce the power consumption, size, and cost of wearable electronics. To achieve this goal, the use of microelectromechanical systems (MEMS) sensors for simultaneous sensing and computing is introduced. Specifically, by enabling sensing and computing locally at the MEMS sensor node and utilizing the usually unwanted pull in/out hysteresis, we may eliminate the need for cloud computing and reduce the use of analog-to-digital converters, sampling circuits, and digital processors. As a proof of concept, we show that a simulation model of a network of …

Quasi-Static Nonlinear Seismic Assessment Of A Fourth Century A.D. Roman Aqueduct In Istanbul, Turkey, Semih Gonen, Ece Erdogmus, Engin Karaesmen, Erhan Karaesmen

Durham School of Architectural Engineering and Construction: Faculty Publications

The majority of architectural heritage consists of load-bearing masonry components made up of stone units and relatively weak mortar joints, yielding potential weak planes for masonry structures where tension and shear failures are expected to occur. Advanced nonlinear analyses are required to simulate these phenomena and predict the corresponding nonlinear structural behavior of historic masonry constructions. In this context, this paper presents a model of a stone masonry Roman aqueduct (the Valens Aqueduct), constructed in the fourth century A.D. in Istanbul, Turkey, to explore the seismic capacity and behavior using the discrete element method (DEM). The employed modeling approach comprises …

Feasibility Of Lora For Smart Home Indoor Localization, Kyungki Kim, Sining Li, Milad Heydariaan, Nour Smaoui, Omprakash Gnawali, Wonho Suh, Min Jae Suh, Jung In Kim

Durham School of Architectural Engineering and Construction: Faculty Publications

With the advancement of low-power and low-cost wireless technologies in the past few years, the Internet of Things (IoT) has been growing rapidly in numerous areas of Industry 4.0 and smart homes. With the development of many applications for the IoT, indoor localization, i.e., the capability to determine the physical location of people or devices, has become an important component of smart homes. Various wireless technologies have been used for indoor localization includingWiFi, ultra-wideband (UWB), Bluetooth low energy (BLE), radio-frequency identification (RFID), and LoRa. The ability of low-cost long range (LoRa) radios for low-power and long-range communication has made this …

To What Extent Can Innovative International Project Delivery Strategies (Which Leverage Bim) Improve The Cost Certainty Of Large Complex Public Procurement Projects In The Context Of Irish Public Procurement?, Bim Tudublin, Roqaya Abouklaib

Capstone Reports

Cost overrun is one of the biggest issues in the construction sector, and cost certainty is one of the main aims of the public construction sector in Ireland. Studies have shown that multi-disciplinary collaboration will benefit a construction project throughout its lifecycle. BIM, Lean, and IPD are independent methodologies that encourage collaborative work, and there are existent effective synergies among these concepts. The synergetic innovative international strategies were utilised for delivering large complex projects successfully globally, and many authors have studied large complex public projects that have adopted innovative international project delivery strategies collaboratively and have shown that the cost …

A Critical Analysis Of The Application Of Augmented Reality (Ar) For Monitoring And Documentation Of Construction Site Progress In The Irish Aec Industry., Bim Tudublin, Lukasz Sarnot

Capstone Reports

Sarnot, L. (2021) A critical analysis of the application of augmented reality (AR) for monitoring and documentation of construction site progress in the Irish AEC industry, Capstone Project from the MSc in aBIMM

A Critical Examination Of Visual Programming And Generative Design For The Compliance Checking Of Open Plan Office Layouts Against Hse Guidelines Post Covid-19., Bim Tudublin, Ronan Byrne

Capstone Reports

The purpose of this study is to explore the feasibility of Visual Programming (VP) and Generative Design (GD) in assisting employers review open plan office layouts against Ireland’s HSE guidelines implemented in May 2020 in response to Covid-19. The pandemic has affected all areas of life with workplace standards requiring a complete overhaul. This study will attempt to ascertain compliance with natural ventilation and social distancing requirements through the completion of an experimental research study, utilising Computational Design (CD) tools. A GD study will be undertaken to provide the designer with numerous office layout design solutions to evaluate and evolve. …

Opportunities In The Irish Reinforced Concrete Industry For Lean And Bim Adoption, Bim Tudublin, Kieran Mcconnell

Capstone Reports

The Irish Reinforced Concrete (RC) sector has yet to realise the full potential of Building Information Modelling (BIM) and Lean construction. The positive impacts and benefits of both BIM and Lean in the wider Architecture, Engineering and Construction sector are widely recognised; many of these are transferable to the RC sector, but there is limited research and knowledge on practical transference, uses and advantages. This research aims to fill some of the existing knowledge gaps by examining BIM and Lean adoption and awareness in the Irish RC sector across sub-sectors, professions, and organisational levels, and by exploring opportunities for increasing …

A Critical Analysis Of How Large Irish Architectural Practices Responded To Initial Covid-19 Restrictions And The Affect Implementing Remote Working Had On Bim Processes, Policies, And People, Bim Tudublin, John Mcenroy

Capstone Reports

The unprecedent events which transpired in the 88-day period from the 31st of December 2019 to the 27th of March 2020 have changed the world in which we live and work. The outbreak of Coronavirus disease 19 (COVID-19) and the ensuing pandemic which has evolved are descripted as one in a hundred-year events. This paper researched and critically analyses the operations which large Irish Architecture firms initiated during this period in order to facilitate the ability of its employees working from a remote location, focusing on how the People, Processes and Policies of BIM (3 Ps of BIM); adapted to …