Architecture Commons^™

Ann Based Load Identification And Forecasting System For The Built Environment, Hosen Hasna

Durham School of Architectural Engineering and Construction: Dissertations, Thesis, and Student Research

"Phantom Loads" cause energy waste in homes and the built environment as a whole. Consumers spend more than $3 billion a year on "Phantom Load" in the United States alone. The goal of this work is to conserve energy by increasing consumer awareness on their energy usage and appropriate tools which in turn will be reducing and /or eliminating phantom loads and mismanagement of the load in the built environment. A further goal is to improve upon existing power distribution systems in the built environment with limited hardware additions to increase energy conservation. This work investigates remote identification of load …

Led Street Light Research Project, Donald K. Carter, Stephen Quick

Stephen Quick

The City of Pittsburgh planned to replace its existing 40,000 street lighting fixtures with LED fixtures and engaged the Remaking Cities Institute (RCI) to investigate the full range of potential benefits of a replacement program in business districts. The study team investigated the technological potentials offered by LED lighting, best management practices (BMP) in LED lighting and lessons learned from cities where LED lighting has been installed, as well as the place-making and aesthetic impact of LED lighting and associated technologies. The team also investigated issues raised by the use of LEDs as the light source and issues of replacing …

Transferts De Chaleur Dans Un Réacteur Thermochimique Solaire Muni D’Un Récepteur Volumique Poreux, Hernando Romero Paredes Rubio

Hernando Romero Paredes Rubio

Un réacteur thermochimique solaire de 1 kW muni d’une structure céramique poreuse en céramique est modélisé pour simuler les transferts thermiques a l’intérieur du récepteur volumétrique. Le modèle développé a été utilisé pour prévoir le comportement thermique du réacteur en fonction des différentes conditions opératoires qui concernent le débit de gaz inerte, le flux solaire incident, la porosité, la longueur du récepteur, et la prise en compte de réactions chimiques. Les résultats montrent que la température maximale est de 1850K pour une concentration solaire de 1000 soleils. La température diminue de manière significative lorsque le débit de gaz augmente. Un …

Develop Energy Dashboard For Real-Time Campus Energy Use Monitoring, Hsui-Lin Winkler, Charlene Hoegler, William Batina

Cornerstone 3 Reports : Interdisciplinary Informatics

No abstract provided.

Development Of A Novel Methodology For Indoor Emission Source Identification, Kwanghoon Han

Kwanghoon Han

The objective of this study was to develop and evaluate a methodology to identify individual sources of emissions based on the measurements of mixed air samples and the emission signatures of individual materials previously determined by Proton Transfer Reaction-Mass Spectrometry (PTR-MS), an on-line analytical device. The methodology based on signal processing principles was developed by employing the method of multiple regression least squares (MRLS) and a normalization technique. Samples of nine typical building materials were tested individually and in combination, including carpet, ceiling material, gypsum board, linoleum, two paints, polyolefine, PVC and wood. Volatile Organic Compound (VOC) emissions from each …

Hybrid Cooling Systems For Low-Temperature Geothermal Power Production, Andrea Ashwood, Desikan Bharathan

Publications (E)

The overall objective of this investigation is to identify and evaluate methods by which the net power output of an air-cooled geothermal power plant can be enhanced during hot ambient conditions using minimal amounts of water.

Geothermal power plants that use air-cooled heat rejection systems experience a decrease in power production during hot periods of the day. This decrease in power output typically coincides with the time when utilities need power to address high air conditioning loads. Hybrid cooling options, which use both air and water, have been studied for this report to assess how they might mitigate the net …

Universal Engineering Programmer – An In-House Development Tool For Developing And Testing Implantable Medical Devices In St. Jude Medical, Khoa Tat Do

Master's Theses

During development and testing of the functionality of the pacemaker and defibrillator device, engineers in the St. Jude Medical Cardiac Rhythm Management Division use an in-house development tool called Universal Engineering Programmer (UEP) to ensure the device functions as expected, before it can be used to test on an animal or a human during the implantation process. In addition, some applications of UEP are incorporated into the official releases of the device product. UEP has been developed and used by engineers across departments in the St. Jude Medical Cardiac Rhythm Management Division (CRMD). This thesis covers the flexible and reusable …