Digital Commons Network^™

Depressurization Characteristics Of Steam-Based Reciprocating Vacuum Pump, Hongling Deng

Dissertations

This dissertation introduces a novel vacuum technology that leverages low-pressure saturated steam and cooling-controlled condensation, offering an efficient way to utilize low-grade thermal energy sources like waste heat, steam, or solar energy. At the heart of this technology is a unique duo-chamber vacuum pump system, featuring a reciprocating piston and a heat-conductive wall, designed to generate a vacuum through steam-condensation and cooling processes.

The core of this research lies in developing and validating mechanistic models for the steam-condensation depressurization process, a complex phenomenon involving phase change and transport mechanisms. Prior to this work, these mechanisms were not sufficiently modeled or …

Borophene And Graphene For Non-Enzymatic Biosensor- Ab-Initio Study, Omar A. Ismail

Theses and Dissertations

Non-enzymatic glucose sensing holds promise to overcome limitations associated with glucose oxidase, such as oxygen dependence and short shelf life. This study explores the potential sensing capabilities of borophene and graphene through direct interaction with various compounds, including β-glucose, uric acid, ascorbic acid, fructose, and acetaminophen. Using Density Functional Theory (DFT), we calculated binding energies and the respective Density of States (DOS) for these adsorbates on both graphene and borophene surfaces. Preliminary results suggest that borophene might exhibit nearly twice the affinity for β-glucose compared to graphene. Moreover, the calculated Density of States reveals distinct distortions in the electronic states …

Rans-Dns Simulations For Uncertainty Quantification In Dns Data Of Turbulent Mixing Layer, Mohamed Abuhegazy

Mechanical Engineering ETDs

Mixing layer flow is one of the canonical free shear flows in fluid dynamics. Such a flow is formed when two fluid streams move along one another with different velocities. Investigation of this flow development has been an active topic of research for many decades not only due to a wide range of environmental and technological applications where this flow may be observed, but also because of large discrepancies in the results obtained experimentally and numerically regardless this flow simple geometry. In this dissertation, the quality and uncertainty of extracted turbulent statistics of mixing layer flow are analyzed by applying …

Screw Dislocations In A Holed Wedge, Gregory T. Whiteside

Mechanical Engineering ETDs

A numerical code has been designed and implemented to find the stress at any material point in a holed-wedge material due to any number of crystal or real screw dislocations in the wedge. The code implements the image dislocation method together with the collocation point method to find stresses at any material point. We demonstrate that the combined analytical-numerical method (analytical with the image dislocations and numerical with the collocation-point method) is valid in that it produces stress fields giving rise to zero traction on free surfaces as well at an arbitrary number of collocation points on void surfaces. Additionally, …

Aerodynamic Dimpling For The Nose Cone Of A High-Power Competition Rocket, Graham Geoffrey Monroe

Mechanical Engineering ETDs

This thesis investigates nose cone dimpling for the reduction of the aerodynamic drag of a Level 3 High-Power amateur rocket. Two rocket launches were conducted. The first used a COTS nose cone with a smooth surface. A dimple distribution was created according to dimensions calculated by Sandia National Laboratories’ proprietary Right- Size Dimple Evaluator. A dimpled nose cone, designed with geometry matching the COTS component, was 3D printed. Axial acceleration and barometric pressure data, recorded by an onboard flight computer, were used to calculate and plot the drag coefficient as a function of the Reynolds number for the smooth and …

Modeling Of Asphalt Concrete For Cross-Anisotropic Visco-Elasticity And Heterogeneity, Zafrul Hakim Khan

Civil Engineering ETDs

Asphalt Concrete (AC) is a cross-anisotropic viscoelastic material. This study has developed a methodology to backcalculate the cross-anisotropic properties of the AC layer from the Falling Weight Deflectometer (FWD) sensor and pavement response data from embedded sensors inside a pavement section. This study has also developed a two-way coupled Multiscale Finite Element Model (MsFEM) with Phase Field Fracture (PFF) to study the microstructural heterogeneity and damage of the AC layer based on the actual field loadings. A Finite Difference Time Domain (FDTD) and Machine learning-based backcalculation algorithm were developed to determine the layer thickness and dielectric constant from air-coupled Ground …

Main Effects Screening Study Of Fe/Kclo4 Thermal Battery Heat Pellet Resistive Activation, Bryan T. Steiner

Mechanical Engineering ETDs

Thermal battery iron-potassium perchlorate (Fe/KClO₄) heat pellets are often ignited by explosive igniters or heat paper. An alternative direct electrical ignition method via resistive heating is explored, which could improve thermal battery manufacturability and design flexibility. A main effects screening experiment was performed with the goal of confirming prior observed trends under more realistic test conditions and ranking the importance of design factors, to optimize future experiments and develop knowledge of the performance space. Relevant literature is examined to advance a theoretical understanding of resistive activation. Ignition sensitivity (go/no-go and time to ignition) and ignition energy are primary …

Control Of Fully-Actuated Aerial Manipulators And Omni-Directional Multirotors, Riley M. Mccarthy

Mechanical Engineering ETDs

This thesis details the system modeling, design, control, simulation, construction, and
testing of both a fully-actuated and omni-directional multirotor aerial system created
for the primary purpose of performing active tasks with their environment. This work
verifies the capabilities of both systems through empirical testing, and demonstrates
how through the use of new control methods and physical designs multirotors can
expand their purpose from passive inspection based tasks to active contact based
tasks. These systems take advantage of newly implemented control allocation features present in the PX4 flight control software, version 1.14. The use of which makes designing controllers for such …

Design, Fabrication And Characterization Of Zero Power Sensor/Harvester For Smart Grid Applications, Zeynel Guler

Mechanical Engineering ETDs

This study presents a flexible sensor/harvester device to be used in both electromagnetic sensing and energy harvesting applications for smart grids. When a current passes through a wire, the sensor detects the magnetic field created by that current. The sensor magnet interacts with the wire magnetic field resulting in a transfer of energy through the piezoelectric cantilever. Piezoelectric, conductive, magnetic, and magnetostrictive composite thin films were prepared to fabricate this device.

Initially, the magnet of the cantilever was optimized considering its shape, thickness, length, taper angle etc. via both simulations and experiments. Peak to peak voltage versus cantilever position graph …

Investigation Of Thermofluid Processes In A Pcm Based Thermal Storage Module, Luca M. Crnjac

Electronic Thesis and Dissertation Repository

Latent heat thermal energy storage systems can capture and store solar thermal energy, enhancing the reliability of solar energy by facilitating a continuous and consistent energy supply. However, phase change materials used in these systems suffer from low thermal conductivities making it difficult to achieve suitable charging and discharging rates. The present research investigated this issue using computational and experimental approaches to improve the design of a thermal storage module through heat transfer enhancement. Various heat transfer enhancements including a finned honeycomb structure, and metal wool were incorporated into a thermal storage module to analyze their effect on charging and …

Advances In Cellulose Nanomaterial-Based Foams For Environmental Applications, Md Musfiqur Rahman

Electronic Theses and Dissertations

The use of metal-oxide nanoparticles adsorbents is limited to fixed-bed columns in industrial-scale water treatment applications. This limitation is commonly attributed to the tendency of nanoparticles to aggregate, the use of non-sustainable and inefficient polymeric resins as supporting materials, or a lack of adsorption capacity. Foams and aerogels derived from cellulose nanomaterials have unique characteristics, such as high porosity and low density, which enables their use in a variety of environmental applications, including water treatment. However, the overall use of cellulose nanomaterial-based foams in various environmental sectors is limited due to the high cost of production associated with time- and …

Floating Offshore-Wind And Controls Advanced Laboratory Program: 1:70-Scale Testing Of A 15 Mw Floating Wind Turbine, Matthew J. Fowler

Electronic Theses and Dissertations

This thesis presents results from the Floating Offshore-wind and Controls Advanced Laboratory (FOCAL) Experiment which performed 1:70-scale model testing of a 15 mega-watt floating offshore wind turbine (FOWT) at the University of Maine’s Alfond Wind/Wave Ocean Engineering Laboratory (W2). The experimental campaigns supported the application of controls co-design to FOWTs by incorporating real-time wind turbine control and hull mounted tuned-mass damper (TMD) elements. A performance-matched scaling strategy was proposed and analysis in OpenFAST performed to design the scale models, including integration of the Reference OpenSource Controller (ROSCO) and modeling of the TMDs in the hull. Four test campaigns were conducted, …

Experimental Measurement Of Near-Field Radiative Heat Transfer Between Two Macroscale Planar Media, Md Shofiqul Islam

Electronic Theses and Dissertations

Radiative heat transfer between two media separated by a gap smaller than the wavelength of thermal radiation (10 μm at room temperature) is referred to as near-field RHT. Near-field RHT exceeds the RHT between two blackbodies which is the maximum limit for RHT in the far-field regime (i.e., when the separation gap is much larger than the thermal wavelength). Due to this enhanced heat transfer, near-field RHT has found promising applications, for power enhancement of thermophotovoltaic devices, thermal rectification, localized cooling, and photonic cooling to name only a few. Graphene is an ideal material for near-field RHT applications as it …

Effects Of Back Reflectors And Thin Metal Covers On The Performance Of Near-Field Thermophotovoltaic Devices, Mehran Habibzadeh

Electronic Theses and Dissertations

Highly efficient energy harvesting devices that can recover a large amount of waste energy are of significant interest. Thermophotovoltaics (TPVs) are solid-state devices that can convert thermal energy radiated by a heated emitter into electrical power through the process of photovoltaic effect. In a TPV system, heat is converted to electricity by using a high-temperature emitter to radiate photons, which are then absorbed by a photovoltaic (PV) cell, generating electron-hole pairs and producing electrical power.

TPV devices have the advantages of producing High efficiency and being lightweight with low maintenance cost and zero pollution. However, these devices have not been …

Numerical Investigation Of Subglottal Stenosis Effects On Human Voice Production, Dariush Bodaghi

Electronic Theses and Dissertations

This dissertation aimed to advance knowledge of how subglottal stenosis impacts voice production physiology. An in-house fluid-structure-acoustic interaction approach based on the hydrodynamic/acoustic splitting technique was employed. This technique was rigorously verified for simulating phonation by matching the acoustic behavior to a compressible flow solver for phonation-relevant geometries. Simulations of an idealized 2D vocal tract model demonstrated the effects of supraglottal acoustic resonance on vocal fold kinematics and glottal flow waveform. Results showed that the acoustic coupling between higher harmonics and formats generated pressure oscillations, modifying vocal fold dynamics and glottal flow rate.

A major novelty was the incorporation and …

Characterizing Tkr Biomechanics Using A Novel Muscle-Driven Joint Motion Simulator, Alexandre Galley

Electronic Thesis and Dissertation Repository

Total knee replacement (TKR) is the end-stage treatment for severe cases of knee osteoarthritis (OA). Despite its success in alleviating pain and restoring mobility to the knee, patient satisfaction rates post-TKR are still lower than other common joint replacement surgeries. Knee kinematics and stability, key determinants of successful TKR, are assessed intraoperatively and tracked post-operatively in in vivo clinical studies. However, the persistently low satisfaction rates suggest that more sophisticated pre-clinical testing methods are needed to better understand the biomechanics of these implants early in their development. During pre-clinical testing of TKR implants, different joint motion simulators are used for …

Residential Indoor Air Quality Study – Assessment And Mitigation, Giovanni Cerrato

Mechanical Engineering Theses

An increased awareness in residential indoor air quality (IAQ) has led to an increase in technologies that assist in improving IAQ. Two such technologies include Electro-static (ES) air cleaners and Photocatalytic Oxidizing (PCO) air cleaners. ES air cleaners remove particulate matter from indoor air, but are known to emit ozone, a contaminant, as a by-product. PCO air cleaners abate gaseous pollutants (i.e., Volatile Organic Compounds, VOCs); however, a lack of testing standards creates confusion about their effectiveness in improving IAQ in a real residential home. On the other hand, environmental variables such as temperature and humidity were found to affect …

Clean Energy & Sustainable Environment By Carbon Dioxide Mitigation Strategies, Md Fahim Shahriar

Mechanical Engineering Theses

Dissolution trapping is one of the most dominant mechanisms for secure storage of CO₂ injected in porous subsurface formations saturated with brine. This study uses a 2D visual Hele-Shaw cell to investigate and visualize the impact of CO₂ injection locations, reservoir dipping angle, permeability heterogeneity, and brine with different initial ionic concentrations on the density-driven convection during CO₂ dissolution (Chapter 2). Also, the role of complex heterogeneity, i.e., irregular permeability distribution in CO₂ dissolution, is investigated using a novel experimental approach to create medium permeability heterogeneity in Hele-Shaw cells (Chapter 3). We observed that the presence …

Study Of Multi-Dimensional Transfer Effects In Applied Smouldering Systems, Seyed Ziaedin Miry Mr

Electronic Thesis and Dissertation Repository

Smouldering is a flameless form of combustion that is driven by oxygen directly diffusing into the surface of condensed phase fuel (liquid or solid) and involves a complex interplay between heat and mass transfer through porous media, chemical reactions, and multiphase flow. Applied smouldering systems have been gaining popularity for a variety of applications including (i) energy and resource recovery, (ii) waste-to-energy, (iii) pyrolysis and gasification, and (iv) applied smouldering of organic liquids/solids for environmental benefits. In all contexts, smouldering is a complicated oxygen-limited phenomenon where multi-dimensional transfer effects (i.e., non-uniformities in …

Comparison Of Methods For Estimating Instantaneous Turn Radius Of Ackermann Steering Vehicles, Kenneth Gennaro Stutts

Doctoral Dissertations and Master's Theses

The instantaneous turn radius of an Ackermann steering vehicle is the distance to a point in space about which the vehicle will travel in an arc during a turn. There are at least six ways to estimate instantaneous turn radius and each method uses different inputs and has distinct advantages and disadvantages. In this thesis, six different methods will be used to estimate the instantaneous turn radius of a vehicle traveling on a closed circuit. This testing will clarify similarities and differences between the methods. This thesis clarifies which method will be the most appropriate for a given set of …

Understanding Real-World And Laboratory Traumatic Brain Injury (Tbi) Using The Computational Model With Brain Functional Regions, Kewei Bian

Electronic Thesis and Dissertation Repository

Traumatic brain injury (TBI), including mild traumatic brain injury (mTBI) or concussion, is a severe health concern. Many symptoms, such as headache, dizziness, and working memory deficits, are reported to be related to the dysfunction of brain functional regions, but the underlying mechanism remains unknown. Hence, further developing tools and analyses to understand brain dysfunction for better TBI prevention are important. Additionally, such analyses should be conducted for both real-world TBI cases and laboratory studies, as TBI data can only be collected from the real world, and prevention measures, such as helmets, are developed and evaluated in the lab. Accordingly, …

Performance Recovery Of Scale Reduced Cyclone Particle Separators Using A Rotating Classifier, Mark J. Parker

Electronic Thesis and Dissertation Repository

Cyclone particle separators are often used to collect particles that are of value or environmental concern. These devices achieve high Total Collection Efficiency (TCE) with steady pressure drop. Increasing the height of the cyclone improves both TCE and pressure drop. However, due to the height of the cyclone, these devices are often forced to be placed outside, which can lead to decreased performance over time. The research examines the outcome of scale reducing a cyclone. This is achieved by (i) how the scale reduction changes the flow field, (ii) identifying what flow aspects contribute to the reduction in TCE and …

Dynamics Modeling Of Molten Salt Reactors, Visura Umesh Pathirana

Doctoral Dissertations

The abundance of energy is a necessity for the prosperity of humans. The rise in energy demand has created energy shortages and issues related to energy security. Nuclear energy can produce vast amounts of reliable energy without many of the negative externalities associated with other competing energy sources, such as coal and natural gas. As a result, public interest in nuclear power has increased in the past decade. Many new types of nuclear reactor are proposed. These nuclear reactor designs feature many passive technologies that can operate without external influence. Reactors that feature advanced passive safety features are catagorized as …

Band Motor Crankshaft For Hydrogen Combustion Engine, Lincoln Hofer, Jacqueline Mendoza Cortes, Austin Rhee, Roze Raymond

Mechanical Engineering

This report outlines the steps in which a group of four mechanical engineers at California Polytechnic State University California, San Luis Obispo, addressed an issue brought up by Professor Roger Benham from the Materials Department. The task included developing an automated and modular testing platform for a revolutionary concept crankshaft prototype – meant for a hydrogen combustion engine - developed and produced by the sponsor: Roger Benham. A testing platform is necessary to measure the performance of the shaft design created to eventually implement this subsystem into a complete hydrogen engine design. Values being tested include geometric validation, maximum static …

Slitter Blade Sharpener, Griffin Buchan, Regan Lane, Kinsale Sproule

Mechanical Engineering

Within this document, our team, “Think Sharpener”, will discuss the following work we have completed since the Critical Design Review: material and part procurement, the manufacturing process for our prototype, and a discussion of our results from testing our final Verification Prototype (VP). To summarize our team’s work during the last portion of this project, our design for the slitter blade sharpening mechanism required us to consult the IME department for materials and manufacturing guidance, order pneumatic components from various online hardware companies, and test our VP to verify we met the engineering design specifications. Our slitter blade sharpening mechanism …

Road Embedded Traffic Actuated Turbine (Retat), Derek Terry Cedillo, Jairo Fernandez Garcia, Alejandro Samaniego, Yosef Towfique

Mechanical Engineering

The Road Embedded Traffic Actuated Turbine (RETAT) project aims to revolutionize sustainable energy solutions by harnessing the power of passing vehicles to generate electricity. This Final Design Review (FDR) encapsulates the evolution of the project, from conceptualization to the tangible realization of the Verification Prototype created by a team of mechanical engineering students. The RETAT boasts an innovative design, incorporating square steel tubing and a unique linear-to-rotational energy conversion mechanism. This report provides a comprehensive overview of the design, implementation, and testing phases, highlighting achievements, challenges, and areas for refinement. As the RETAT project strives to contribute to a cleaner, …

Tagalong Trail, Sean Wahl, Jason Davis, Quinlan Stephens, Ryan Johnson, Vinh Vo

Mechanical Engineering

The Cal Poly mechanical engineering team working on the Path of Lights and Sounds for the Girl Scouts of California’s Central Coast has now completed their project. In the last quarter of their project, they were able to finalize their tile’s structural design while iterating through several electronics board designs. Through this iteration, they were able to create a final electronics board and designed a water-resistant enclosure to house the board. A new team member was added, allowing them to manufacture 28 tile structures and 30 electronics assemblies over the course of two and a half weeks. This proved to …

Interactive Water Vortex Exhibit, Simon Way, Emily Laing, Roqaya Naseri, Makenzie Kan

Mechanical Engineering

The San Luis Obispo Children’s Museum requested an interactive water vortex exhibit to both engage and entertain inquisitive guests, ages two to eight. The goal was to design and manufacture an exhibit that would educate its users on the fluid mechanics behind water vortices. They activate the mechanics by spinning a wheel, which is perceived as the catalyst to manipulate the flow of water to successfully create a whirlpool. Our team has created an interactive display that will enlighten young minds, providing the museum with an educational exhibit which shares a concept not currently taught by any other. Our project …

Stress Relaxation Cracking In 347h Austenitic Steel Weldments Under Various Heat Treatments: Experiments And Modeling, Yi Yang

Doctoral Dissertations

347H austenitic stainless steel exhibits exceptional creep and corrosion resistance, rendering it an exemplary candidate for pipeline materials, particularly in mid- to high-temperature working conditions. However, due to constraints in component dimensions, welding has been chosen as the preferred method for joining pipeline systems extensively employed in nuclear power plants, fossil fuel plants, and petrochemical companies. The welding process entails the accumulation of residual stress during the cooling stage, along with the introduction of microstructure evolution. Moreover, the residual stress field and microstructure continuously evolve under service conditions, thereby intensifying the susceptibility of crack initiation and propagation. The initial residual …

A Two-Diameter Helical Endmill Beam Model For Tool Tip Dynamics Prediction With Application To Milling, Emma D. Betters

Doctoral Dissertations

The aim of this dissertation is to describe the dynamic response of helical endmill geometries to enable the use of receptance coupling substructure analysis (RCSA) to predict the tool tip vibration response of arbitrary tool-holder-spindle-machine combinations. The tool tip vibration response, or receptance, is a key input for milling stability prediction. Currently, a measurement is required to determine the tool tip receptance for each tool-holder-spindle-machine combination, which may not be possible in production environments. In the RCSA approach, the spindle receptances are measured once and archived, while the tool and holder are modeled. Tool tip receptances are predicted by analytically …