Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 9 of 9
Full-Text Articles in Entire DC Network
Integration Of A Prototype Wireless Communication System With Micro-Electromechanical Temperature And Humidity Sensor For Concrete Pavement Health Monitoring, Shuo Yang, Keyan Shen, Halil Ceylan, Sunghwan Kim, Daji Qiao, Kasthurirangan Gopalakrishnan
Integration Of A Prototype Wireless Communication System With Micro-Electromechanical Temperature And Humidity Sensor For Concrete Pavement Health Monitoring, Shuo Yang, Keyan Shen, Halil Ceylan, Sunghwan Kim, Daji Qiao, Kasthurirangan Gopalakrishnan
Daji Qiao
In recent years, structural health monitoring and management (SHMM) has become a popular approach and is considered essential for achieving well-performing, long-lasting, sustainable transportation infrastructure systems. Key requirements in ideal SHMM of road infrastructure include long-term, continuous, and real-time monitoring of pavement response and performance under various pavement geometry-materials-loading configurations and environmental conditions. With advancements in wireless technologies, integration of wireless communications into sensing device is considered an alternate and superior solution to existing time- and labor-intensive wired sensing systems in meeting the requirements of an ideal SHMM. This study explored the development and integration of a wireless communications sub-system …
Mems Resonant Magnetic Field Sensor Based On An Aln/Fegab Bilayer Nano-Plate Resonator, Yu Hui, Tianxiang Nan, Nian Sun, Matteo Rinaldi
Mems Resonant Magnetic Field Sensor Based On An Aln/Fegab Bilayer Nano-Plate Resonator, Yu Hui, Tianxiang Nan, Nian Sun, Matteo Rinaldi
Nian X. Sun
This paper reports on the first demonstration of an ultra-miniaturized, high frequency (215 MHz) and high sensitivity MEMS resonant magnetic field sensor based on an AlN/FeGaB bilayer nano-plate resonator capable of detecting magnetic field at nano-Tesla level. Despite of the reduced volume and the high operating frequency of the sensor, high electromechanical performances were achieved (quality factor Q ≈ 511 and electromechanical coupling coefficient kt² ≈ 1.63%). This first prototype was characterized for different magnetic field levels from 0 to 152 Oe showing a frequency sensitivity of ~ 1 Hz/nT and a limit of detection of ~ 10 nT.
Nanoenabled Microelectromechanical Sensor For Volatile Organic Chemical Detection, Chiara Zuniga, Matteo Rinaldi, Samuel M. Khamis, A. T. Johnson, Gianluca Piazza
Nanoenabled Microelectromechanical Sensor For Volatile Organic Chemical Detection, Chiara Zuniga, Matteo Rinaldi, Samuel M. Khamis, A. T. Johnson, Gianluca Piazza
Matteo Rinaldi
A nanoenabled gravimetric chemical sensor prototype based on the large scale integration of single-stranded DNA (ss-DNA) decorated single-walled carbon nanotubes (SWNTs) as nanofunctionalization layer for aluminum nitride contour-mode resonant microelectromechanical (MEM) gravimetric sensors has been demonstrated. The capability of two distinct single strands of DNA bound to SWNTs to enhance differently the adsorption of volatile organic compounds such as dinitroluene (simulant for explosive vapor) and dymethyl-methylphosphonate (simulant for nerve agent sarin) has been verified experimentally. Different levels of sensitivity (17.3 and 28 KHz µm^2/fg) due to separate frequencies of operation (287 and 450 MHz) on the same die have also …
Nanoindentation And Micro-Mechanical Fracture Toughness Of Electrodeposited Nanocrystalline Ni-W Alloy Films
A.S. Md Abdul Haseeb
Nanocrystalline nickel-tungsten alloys have great potential in the fabrication of components for microelectromechanical systems. Here the fracture toughness of Ni-12.7 at.%W alloy micro-cantilever beams was investigated. Micro-cantilevers were fabricated by UV lithography and electrodeposition and notched by focused ion beam machining. Load was applied using a nanoindenter and fracture toughness was calculated from the fracture load. Fracture toughness of the Ni-12.7 at.%W was in the range of 1.49-5.14 MPa √m. This is higher than the fracture toughness of Si (another important microelectromechanical systems material), but considerably lower than that of electrodeposited nickel and other nickel based alloys. © 2012 Elsevier …
Nanoindentation And Micro-Mechanical Fracture Toughness Of Electrodeposited Nanocrystalline Ni-W Alloy Films
A.S. Md Abdul Haseeb
Nanocrystalline nickel-tungsten alloys have great potential in the fabrication of components for microelectromechanical systems. Here the fracture toughness of Ni-12.7 at.%W alloy micro-cantilever beams was investigated. Micro-cantilevers were fabricated by UV lithography and electrodeposition and notched by focused ion beam machining. Load was applied using a nanoindenter and fracture toughness was calculated from the fracture load. Fracture toughness of the Ni-12.7 at.%W was in the range of 1.49-5.14 MPa √m. This is higher than the fracture toughness of Si (another important microelectromechanical systems material), but considerably lower than that of electrodeposited nickel and other nickel based alloys. © 2012 Elsevier …
Switch-Less Dual-Frequency Reconfigurable Cmos Oscillator Using One Single Piezoelectric Aln Mems Resonator With Co-Existing S0 And S1 Lamb-Wave Modes, Chengjie Zuo, Jan Van Der Spiegel, Gianluca Piazza
Switch-Less Dual-Frequency Reconfigurable Cmos Oscillator Using One Single Piezoelectric Aln Mems Resonator With Co-Existing S0 And S1 Lamb-Wave Modes, Chengjie Zuo, Jan Van Der Spiegel, Gianluca Piazza
Chengjie Zuo
For the first time, this work demonstrates a switch-less dual-frequency (472-MHz and 1.94-GHz) reconfigurable CMOS oscillator using a single piezoelectric AlN MEMS resonator with co-existing S0 and S1 Lamb-wave modes of vibration. High performances (high Q and kt2 for a resonator and low phase noise for an oscillator) have been achieved for both the resonator and oscillator in terms of dual-mode operation. Especially, the 1.94-GHz operation has the best phase noise performance when compared with all previously reported CMOS oscillators that work at a similar frequency.
Nanoenabled Microelectromechanical Sensor For Volatile Organic Chemical Detection, Chiara Zuniga, Matteo Rinaldi, Samuel M. Khamis, A. T. Johnson, Gianluca Piazza
Nanoenabled Microelectromechanical Sensor For Volatile Organic Chemical Detection, Chiara Zuniga, Matteo Rinaldi, Samuel M. Khamis, A. T. Johnson, Gianluca Piazza
Matteo Rinaldi
A nanoenabled gravimetric chemical sensor prototype based on the large scale integration of single-stranded DNA (ss-DNA) decorated single-walled carbon nanotubes (SWNTs) as nanofunctionalization layer for aluminum nitride contour-mode resonant microelectromechanical (MEM) gravimetric sensors has been demonstrated. The capability of two distinct single strands of DNA bound to SWNTs to enhance differently the adsorption of volatile organic compounds such as dinitroluene (simulant for explosive vapor) and dymethyl-methylphosphonate (simulant for nerve agent sarin) has been verified experimentally. Different levels of sensitivity (17.3 and 28 KHz µm^2/fg) due to separate frequencies of operation (287 and 450 MHz) on the same die have also …
Hybrid Ultra-Compact 4th Order Band-Pass Filters Based On Piezoelectric Aln Contour-Mode Mems Resonators, Chengjie Zuo, Nipun Sinha, Carlos R. Perez, Rashed Mahameed, Marcelo B. Pisani, Gianluca Piazza
Hybrid Ultra-Compact 4th Order Band-Pass Filters Based On Piezoelectric Aln Contour-Mode Mems Resonators, Chengjie Zuo, Nipun Sinha, Carlos R. Perez, Rashed Mahameed, Marcelo B. Pisani, Gianluca Piazza
Chengjie Zuo
This work reports on the design, fabrication and testing of a new class of hybrid (filter design using combined electrical and mechanical coupling techniques) ultra-compact (800×120 μm) 4th order band-pass filters based on piezoelectric Aluminum Nitride (AlN) contour-mode microelectromechanical (MEM) resonators. The demonstrated 110 MHz filter shows a low insertion loss of 5.2 dB in air, a high out-of-band rejection of 65 dB, a fractional bandwidth as high as 1.14% (hard to obtain when only conventional electrical coupling is used in the AlN contour-mode technology), and unprecedented 30 dB and 50 dB shape factors of 1.93 and 2.36, respectively. All …
Thermal Stability Of Electrodeposited Liga Ni-W Alloys For High Temperature Mems Applications
Thermal Stability Of Electrodeposited Liga Ni-W Alloys For High Temperature Mems Applications
A.S. Md Abdul Haseeb
For thermally stable LIGA materials for high temperature MEMS applications LIGA Ni-W layers and micro testing samples with different compositions (15 and 5 at% W) were electrodeposited. In order to investigate the thermal stability the Ni-W layers were annealed at different temperatures (300-700°C) and for different durations (1, 4, 16 h). Their microstructure and micro-hardness were than analysed after annealing and compared with those of as-deposited states. The observed microstructures show, in comparison to pure LIGA nickel, a small grain growth and a relatively stable structure up to 700°C. The micro-hardness values of the LIGA Ni-W layers are higher than …