Digital Commons Network^™

Drag Reduction On Non-Ionic Surfactants In Aqueous Systems, Jen-Lin Chang

Masters Theses

"The use of polyoxyethylene alcohol non-ionic surfactants as drag reducing additives in aqueous systems was investigated. Significant drag reduction was obtained with suitable combinations of one percent Alfonic 1214 and salts at 30°C such that the surfactant was near or above its upper critical solubility temperature. Maximum drag reduction was observed at the cloud point. Relative viscosity values also peaked at this point. No upper critical shear stress was attained up to wall shear stresses of 2,000 dynes/cm² with one percent Alfonic 1214 solutions at their cloud points.

At a fixed temperature, the salt concentration required to reach the …

Computer-Aided Circuit Optimization Including The Adjoint Method Of Calculating Network Sensitivities, John Walter Olson

Masters Theses

"A complete discuss ion of the optimization of a circuit, including modeling and programming difficulties encountered, is presented. A three transistor bandpass filter is used in order to study various methods of optimization. The adjoint method of calculating the network error gradient vector is compared to the perturbation method. The adjoint method proves to have decided advantages over the other method. A generalized computer program is presented to carry out the Fletcher-Powell optimization algorithm with specialized subroutines which include a network equation solver and both methods of finding the gradient vector. The program proved very effective in realizing a desired …

Polynary Silicon Tellurium Glasses, Henry Edward Anthonis

Masters Theses

"The introduction of Ag into Si-As-Te glasses permits the incorporation of Se, otherwise volatile and/or degradable as a constituent in Si-containing chalcogenide glasses. Si-As-Ag-Te-Se glasses exhibit much higher softening ranges and glass transition temperatures than encountered in known chalcogenide systems. A glass Si₃₅As₁₅Ag₁₀Te₂₀Se₂₀ had the viscosity log η =13 at about 500°C, as compared to 370°C for the base glass Si₃₅As₂₅Te₄₀, the viscosity of log η = 9.8 at about 560°C, as compared to 442°C for the base glass Si₃₅As₂₅Te_{40 …}

Studies Of Neutron Capture Produced Rare Gas Isotopes In Rocks And Minerals Containing Chlorine, Selenium And Tellurium, David E. Sinclair

Masters Theses

"Noble gas mass spectrometry was used to study rare nuclear processes in terrestrial rocks and minerals. An excess of ³⁶Ar was detected in a chlorine-rich rock. The excess ³⁶Ar has been produced in rocks near the earth's surface due to capture of cosmic-ray-produced neutrons on ³⁵Cl. Measurement of ³⁶Ar formed by the ³⁵Cl(n, γ)³⁶Cl(β^-)³⁶Ar process makes possible a new method for determining the surface residence time of chlorine-rich minerals

Excess ⁸²Kr and excess ⁸³Kr were detected in selenium-rich ores. The excess ⁸²Kr results from double beta …

Effect Of Glass Aggregates Upon Abrasiveness Of Asphaltic Mixtures, Dwarka Prasad Gupta

Masters Theses

"The utilization of glass as an aggregate in asphaltic concrete pavements has been suggested as a means for reusing the increasing amounts of waste glass generated each year in the United States. Recent studies have shown that asphaltic mixtures containing glass aggregates can be designed to meet Marshall requirements for stability, flow and void content but the abrasiveness of mixtures containing glass aggregates had not been investigated. The objectives of this study were to develop a laboratory wear testing apparatus and compare the abrasiveness of asphaltic concrete mixtures using glass aggregates with the abrasiveness of mixtures using several different conventional …

A Study Of The Effect Of Drilled Holes On The Concentration Of Elastic Stresses Around A Notch, Glenn Michael Kmecz

Masters Theses

"Hole drilling as a method for improving the toughness of notch weakened tensile specimens is investigated by means of a photoelastic technique. Tests were performed on 20%, 40%, 60%, and 80% notch depth specimens machined from PSM-1 photoelastic material. The basic criteria for success was no increase in the elastic stress concentration factor. The photoelastic results were verified by a finite element stress analysis of the 60% notch depth specimens. Comparison of the experimental and numerical results provide conclusive proof that no increase in the elastic stress concentration factor occurs when proper positioning of the drilled holes is accomplished"--Abstract, page …

Fitting Discrete Probabilistic Frequency Distributions To Disturbed Traffic Flow At An Unsignalized Urban Intersection, Horst Walter Kaminsky

Masters Theses

"Traffic variables, such as volume, speed, gaps and lags, and headways can be described by probability distributions. In this study vehicle arrivals from three directions have been recorded at a four-leg, right-angled, at-grade intersection in Rolla, Missouri, and statistically analyzed. Two distinct probabilistic statistical concepts were used, the continuous (gap) and discrete (counting) distribution. The negative exponential distribution is discussed briefly, whereas the applicability of discrete statistical models for the traffic situation selected is elaborated in detail.

The purpose of this research was to investigate the impairment and distortion that various interferences such as upstream traffic lights, bottlenecks or other …

A Study Of Right Turn On Red At Signalized Intersections, Ronald Duane Rains

Masters Theses

"Traffic engineers have discussed the controversial subject of allowing drivers to make a right-turn-on-red (R.T.O.R.) for many years. There have been many strong points given for and against allowing this movement.

Within this paper R.T.O.R. is discussed and conclusions are drawn for a research of literature and questionnaire survey.

Questionnaires were sent to ninety-three cities and all fifty states. Many valuable unwritten facts and opinions were received from the seventy city and thirty-six state traffic engineers that completed and returned the questionnaires.

It was determined that 63.8% of the states replying and 64.3% of the cities are presently utilizing R.T.O.R. …

A Study Of Fmfb Demodulator Operation In The Presence Of Radio Frequency Interference And Gaussian Noise, Terry D. Wormington

Masters Theses

"A digital computer model of an FMFB demodulator has been used to study the effects of radio frequency interference on the detection of a sinusoidally modulated carrier. The effectiveness of selecting the feedback factor to suppress the interference for three values of modulation index is investigated. Also, the required IF bandwidth for the minimization of the mean-square error of the loop output between a signal corrupted by interference and the same signal without interference was investigated. More work is required before the effects of Gaussian noise plus interference on loop operation can be ascertained"--Abstract, page ii.

Sensitivity Analysis In Active Rc Bandpass Circuits, Robert Bentzinger

Masters Theses

"This thesis is concerned with the analysis and cataloguing of sensitivity functions of some selected active RC bandpass networks. The sensitivity functions of primary interest are the sensitivities of the quantities ω_o and Q with respect to changes in the element values of each circuit.

An introduction is provided to give background information on how each circuit is realized. Each circuit is then analyzed and the pertinent sensitivity functions catalogued. Some comments are made as to the approximations which are involved in several of the realizations and the validity of any sensitivity analysis made on these approximate realizations. The …

A Geochemical Reconnaissance Of Puerto Rican Beach Sands, Louis Meinecke Iii

Masters Theses

"Twenty-four beach sand samples from the island of Puerto Rico were collected in 1964 by Dr. Ernst Bolter as part of a radiometric survey conducted by him. These samples were given to the author in 1969 for chemical analysis.

The purpose of this investigation was to conduct a geochemical reconnaissance study of the beach sands in order to determine the geochemical background and possible anomalies. This information could aid in offshore mineral exploration and source area determination.

This thesis presents the results of a quantitative chemical analysis for copper, lead, zinc, iron, manganese, aluminum, sodium, potassium, calcium, magnesium, and strontium …

Thermal Stresses And Movements In Bridges, Joseph Charles Reynolds

Masters Theses

"A state of the art regarding the thermal behavior of bridges and considerations to be given to the resultant thermal effects is presented. The results of studies related to the thermal effects on bridges are reviewed. Studies attempting to relate environmental factors to bridge temperatures, and subsequently to bridge movements and stresses, indicate that the task is extremely complex. Some correlation has been made between equations predicting bridge temperatures and movements based on weather bureau records. However, further research is needed to evaluate the effects of factors other than temperature, such as creep, shrinkage, and humidity on bridge movements and …

An Engineering Analysis Of Fluid Amplifiers And Development Of An Air Velocity Sensor, Gian Sagar Aneja

Masters Theses

"Fluidics, the new control technique finds its use amongst the conventional electronics and pneumatics due to some of its impressive features. Selected literature about bistable and proportional amplifiers has been presented for better understanding of the element behavior. Sensors; typical applications of fluidics have been described separately. An air flow velocity sensor has been set-up. Basically it consists of a cylinder placed across the air flow that sheds vortices in the wake due to 'Von Karman Vortex Street' phenomenon. The frequency of vortices gives a measure of velocity. The velocities obtained from the sensor have been compared to the ones …

Phase Transformations In The System Zro₂-Cao, Damri Sukhotanang

Masters Theses

"Thermal expansion, thermal hysteresis, and the monoclinic tetragonal phase transformation of ZrO₂ have been studied with high temperature x-ray diffractometry. The initial transformation temperature in pure ZrO₂, on heating, is about 1150ºC. The transformation occurs over a 100ºC temperature range and thermal hysteresis occurs on heating and cooling. The mechanism of the transformation is related to preferred vibrational modes of atoms on the A_O -C_O plane of the monoclinic structure. Because the monoclinic B_O axis is parallel with the tetragonal [110] axis, structural relationships can be seen to be a controlling factor in the transformation. Initiation of …

A Comparison Of Liapunov Functions Used To Determine Power System Stability For Multimachine Power Systems, Kiritkumar S. Shah

Masters Theses

"Four Liapunov functions used in stability studies are compared for accuracy on an eight machine power system. This comparison is made to determine which function is best in multimachine stability applications. Morgan's Estimating Technique is used to estimate when the Liapunov function would exceed its maximum value and thus to predict the critical switching time for the system"--Abstract, page ii.

The Steady-State Response Of A Fluid-Filled Beam Near Resonance, Niranjan Jayantibhai Patel

Masters Theses

"In this report the steady-state near-resonant vibration of a hollow fluid-filled beam is considered. The energy dissipation caused by the beam-fluid interaction is approximated by introducing a viscous damping force into the Bernoulli-Euler beam equation. A theoretical expression is developed for the displacement of the hollow beam by solving this modified Bernoulli-Euler beam equation. Tests are made using a cantilevered fluid-filled box to simulate a unit of beam-fluid length. The band-width technique is used to determine the incremental viscous damping coefficient from test data. A variety of fluids are used in the box to determine the effect of the fluid …

Design And Analysis Of A Phase-Locked Loop Suitable For Synchronization Of An Optical Receiver, Douglas Wayne Dreisewerd

Masters Theses

"The required synchronization of a dynamic crossed-field photomultiplier tube (DCFP) is accomplished by means of a phase-locked loop for which the salient feature is the use of the DCFP as the phase detector. This action is necessitated due to the unique sampling and phase focusing type of operation of the DCFP. The phase-locked loop is implemented by dithering the phase of the synchronizing RF drive signal, bandpass filtering the output pulses of the DCFP and using a synchronous detector at the dither frequency to determine the phase relationship between the incoming mode-locked laser pulses and the RF drive signal. The …

A Study Of The System Lithia - Silica, Roy Richard Ramey

Masters Theses

"X-ray intensity and d-spacing measurements were performed upon samples in the system Li₂O-SiO₂. Samples ranged from 0.0 to 28.0 mole percent lithia and were fired for 72 hours at temperatures from 920ºC to 1400ºC. Atomic absorption analyses were made upon the fired samples. Non-equilibrium conditions were prevalent and results are inclusive. Quartz is the stable phase in the high silica field at temperatures below 1050ºC with cristobalite stable above that. The quartz - cristobalite transformation occurs at 950ºC with the cristobalite transforming into tridymite at 1010ºC. There was wide scattering of data at 1000ºC and below. There was no correlation …

A Study Of Three Methods Which Solve A Suboptimum Control Problem On An Iterative Analog Computer, Joseph Camp Finney

Masters Theses

"Three methods for optimizing a proportional and a proportional-integral controller parameter problem were investigated on an iterative analog computer. The three methods were the parameter-perturbation correlation method, the absolute biasing method, and the variable step size method. The process controlled was third order linear. The performance function used to judge the quality of the controller was the time integral of the absolute value of error. All three methods required a trial and error adjustment of the parameters used in these methods. The optimum solution was obtained by all methods. The absolute biasing method, for both the proportional and the proportional-integral …

Wind Tunnel Modeling Of The Atmospheric Boundary Layer, Sreemanth Pagadala

Masters Theses

"The importance of simulating atmospheric flows in wind tunnels has been well established. Experiments were conducted in the Modified Aerodynamic Wind Tunnel to determine the suitability of this wind tunnel for simulating atmospheric flows and the degree to which various aspects of modeling could be fulfilled. A temperature profile to simulate the inversion aloft was generated inside the test section, and then an appropriate velocity profile was built in by means of screen mesh arrangements. The turbulence characteristics of the flow were measured. The validity of the temperature, velocity and turbulence fields were examined. It was found that while the …

A Comparison Of Analytical And Experimental Approaches In Determining The Thermoelastic Stresses Around A Cylindrical Inclusion Of Elliptical Cross-Section, Kenneth Byron Oster

Masters Theses

"Three approaches are used to determine the principal stress differences in an infinite elastic medium containing a cylindrical inclusion of elliptic cross-section due to a uniform temperature change. First, the two-dimensional equations of thermoelasticity are solved resulting in equations for the stress components anywhere in the medium material. Second, boundary displacements based on stress-strain relations are used as input displacements in a finite element program of the medium. Third, these same boundary displacements are used as input displacements on a photoelastic model simulating the medium. The problem is treated as one of plane strain in the first approach and one …

The Analysis Of An Axially Symmetric Submerged Membrane Shell, Walter Earl Wehmeyer

Masters Theses

"The general theory of large elastic deformations is applied to the problem of a liquid-filled, axisymmetric membrane which is supported on a rigid horizontal plane and subjected to a variable external pressure. The variable external pressure is caused by submerging the membrane to various depths. The variation of the hydrostatic pressure in the inflating medium as well as in the surrounding environment is considered. By assuming large meridional deformations the stress field and the deformed shapes of a submerged membrane made of a neo-Hookean material are obtained. The effect of the initial shape on the deformed configuration of the membrane …

Thermal Expansion Of Nickel And Iron, And The Influence Of Nitrogen On The Lattice Parameter Of Iron At The Curie Temperature, Jinn-Wen Hwang

Masters Theses

"By precise X-ray measurements, the lattice parameter of pure nickel (Fisher Co., reagent grade) was found to be 3.52389 Å at 25ºC. At the same temperature, the lattice parameters of iron samples were found to be: 2.86621 Å, 2.86624 Å and 2.86614 Å for purities of 99.999%, 99.985% and 99.9%, respectively. By measuring high angle back reflection lines, the linear coefficients of thermal expansion of both nickel and iron were precisely determined. Both, high purity nickel and iron, exhibited anomalies in their expansion coefficients near their Curie points. This is in agreement with some of the previously reported data. Some …

Investigation Of A New Type Of Cloud Condensation Nuclei Counter: The Thermal Quench Chamber, Donald Arthur Hess

Masters Theses

"The design and development of a new type of cloud condensation nuclei counter was undertaken to provide a new laboratory and field instrument that operates on a different theoretical basis than the thermal diffusion chamber now being used by meteorologists and other scientists. In the new instrument the test aerosol is pumped through a tube where it is first humidified and then cooled at constant pressure to create a supersaturation, causing water vapor to condense upon the nuclei in the aerosol sample. The concentration of cloud condensation nuclei is then determined by counting the water drops. The control of temperature …

Transient Cooling Of A Sphere Due To Boiling, Salil K. Banerjee

Masters Theses

"The time - dependent surface temperature is determined for a sphere subjected to cooling by boiling. One dimensional heat transfer is considered and the solid is assumed to be homogeneous, isotropic and opaque to thermal radiation and to have temperature independent physical properties. The initial temperature of the sphere and the coolant are assumed to be uniform and arbitrary. The boiling heat transfer coefficient at the surface of a sphere is a strong function of the surface temperature thus resulting in an extremely nonlinear transient heat conduction problem. As a practical application of the problem, the process of quenching has …

Parametric Analyses Of Regenerative Steam Power Cycles, Vallabh Vithalbhai Vaghani

Masters Theses

"This study analyzes the effect of inlet pressures, internal turbine efficiencies, pump efficiencies, extraction pressures and number of open feedwater heaters on the thermal efficiency of regenerative steam power cycles. Combinations of inlet and extraction pressures were introduced into digital computer programs in order to find the optimum extraction pressures for maximum thermal efficiency. The scope of study covered regenerative steam cycles with one, two, three, four, and five open feedwater heaters. One of the principle objectives of the study was to determine if there is some turbine extraction pressure or set of pressures which give maximum thermal efficiency for …

Mechanism Of Ual₃ To Ual₄ Transformation, Ling Ping Lee

Masters Theses

"The UAl₄ compound which forms during the peritectic reaction, Liquid + UAl₃ - UAl₄ , has a long needle-like shape and a characteristic morphology of fish-tail when cut along the long axis. It has an internal core of another phase when cut perpendicular to the needle axis. Because of the interesting similarity between UAl₃ and UAl₄ crystal structures, the peculiar UAl₄ morphology could be explained. The mechanism of UAl₃ to UAl₄ transformation is identified as shear and diffusion controlled transformation"--Abstract, page ii.

A Practical Approach To The Exhaust Silencing Of A Pneumatic Rock Drill, Morton Gary Barth

Masters Theses

"One-third octave spectrum analyses of the exhaust noise produced by a medium sized pneumatic rock drill were obtained during free recriprocation to determine the most troublesome bands of noise. Noise reduction techniques were then used to design exhaust mufflers which would reduce the level of the exhaust noise to an acceptable level with a minimum increase in back pressure. The prototype mufflers evaluated included an expansion chamber, a resonator, and various modified expansion chambers. One of the modified expansion chambers tested provided very good attenuation reducing the exhaust noise from 113 dBA to 87 dBA at the operator's ear position. …

Use Of Isotopes To Reduce Neutron-Induced Radioactivity And Augment Thermal Quality Of The Environment Of An Underground Nuclear Explosion, Nathaniel Fred Colby

Masters Theses

"The use of isotopes to include radioactive waste products to reduce the neutron-induced activity of an underground nuclear explosion and its application in the field of geothermal power stimulation is discussed. A shield composed of selected isotopes surrounding a fusion device will capture excess neutrons producing isotopes with short half-lives. Subsequent rapid decay will prolong the high temperature in the vicinity of the explosion and decrease the activity. Long-lived isotopes created by neutron capture in the host rock would be minimized. The investigation is conducted for strontium-90, cesium-137, cerium-144, technetium-99, rhodium-103 and -105. Of these, the first three appear to …

Use Of Glass Separated From Municipal Refuse In Asphaltic Concrete, Thomas Eugene Keith

Masters Theses

"The recent interest in municipal refuse recycling has brought about the development of several systems for separation of the refuse into components. One of the components reclaimed is a glass-rich fraction which, although primarily glass, contains various non-glass materials which the system is not able to remove. Clean waste glass can be used as an asphaltic concrete aggregate, and it would be desirable to use this glass-rich fraction in a similar manner. However, the effect, if any, of the non-glass components on the properties of an asphaltic mixture must be determined in order to utilize the glass-rich fraction with a …