Digital Commons Network^™

Climate Change In Cyprus: Impacts And Adaptation Measures, Theodoros Zachariadis

Theodoros Zachariadis

No abstract provided.

Climate Change In Cyprus – Impacts And Adaptation Policies, Elpida Shoukri, Theodoros Zachariadis

Theodoros Zachariadis

This report provides a literature review of climate change facts and projections globally, for Europe, Mediterranean and Cyprus until the end of the 21st century. It focuses on climate change effects in Cyprus by sector and presents specific recommendations on the implementation of a proper adaptation strategy. The report is based on a review of the most important recent studies on climate change, including reports from international organizations as well as European and Mediterranean authorities and research institutions. The report has also benefited from information gathered through personal communication of the authors with public authorities, non-governmental organizations and researchers.

A Relationship Between Three Analytical Approaches To Nonlinear Problems, Hassan Askari

No abstract provided.

Stability Of Molybdenum Nanoparticles In Sn-3.8ag-0.7cu Solder During Multiple Reflow And Their Influence On Interfacial Intermetallic Compounds

A.S. Md Abdul Haseeb

This work investigates the effects of molybdenum nanoparticles on the growth of interfacial intermetallic compound between Sn-3.8Ag-0.7Cu solder and copper substrate during multiple reflow. Molybdenum nanoparticles were mixed with Sn-3.8Ag-0.7Cu solder paste by manual mixing. Solder samples were reflowed on a copper substrate in a 250 °C reflow oven up to six times. The molybdenum content of the bulk solder was determined by inductive coupled plasma-optical emission spectrometry. It is found that upon the addition of molybdenum nanoparticles to Sn-3.8Ag-0.7Cu solder, the interfacial intermetallic compound thickness and scallop diameter decreases under all reflow conditions. Molybdenum nanoparticles do not appear to …

State Of The Art / Novel Rotary-Turbo-Inflow Tech / Featured Development - Gearturbine Project - Atypical Motor Engine Type, Carlos Barrera

Carlos Barrera

GEARTURBINE PROJECT Atypical InFlow Thermodynamic Technology Proposal Submission Novel Fueled Motor Engine Type

*State of the art Innovative concept Top system Higher efficient percent. Have similar system of the Aeolipile Heron Steam device from Alexandria 10-70 AD. -New Form-Function Motor-Engine Device. Next Step, Epic Design Change, Broken-Seal Revelation. -Desirable Power-Plant Innovation.

YouTube; * Atypical New • GEARTURBINE / Retrodynamic = DextroRPM VS LevoInFlow + Ying Yang Thrust Way Type - Non Waste Looses

-This innovative concept consists of hull and core where are held all 8 bteps of the work-flow which make the concept functional. The core has several gears …

Die Attach Properties Of Zn-Al-Mg-Ga Based High-Temperature Lead-Free Solder On Cu Lead-Frame

A.S. Md Abdul Haseeb

No abstract provided.

10 - استفاده ي مؤثر از شناور حرارتي وسايل گرمايشي احتراقي به منظور کنترل کيفيت هواي داخل, Chamran Nowrouzi, Mehdi Maerefat, Alireza Zolfaghari

Dr Alireza Zolfaghari

No abstract provided.

Varma Steam Turbine, Vijaya Krushna Varma Mr

VIJAYA KRUSHNA VARMA Mr

Varma turbines are ultra modern and high efficiency turbines which can use gas, steam or fuels as feed to produce electricity or mechanical work for wide range of usages and applications in industries or at work sites. Varma turbine engines can be used in all types of vehicles. These turbines can also be used in aircraft, ships, battle tanks, dredgers, mining equipment, earth moving machines etc

Beyond Business-As-Usual: Achieving A Paradigm Shift Towards Low-Carbon Transport, Theodoros Zachariadis

Theodoros Zachariadis

Transportation is responsible for a continuously rising share of global carbon emissions. Carefully designed regulations, supported by land use strategies, fiscal policies and local incentives, and enabled through targeted international development assistance, can reverse these unsustainable trends.

Climate Change In Cyprus: Impacts And Adaptation Policies, Theodoros Zachariadis

Theodoros Zachariadis

This paper provides an overview of facts and projections related to climate change in Cyprus until the end of the 21st century. It highlights the main climate change impacts foreseen and presents recommendations for the preparation of a national adaptation strategy. Coping with climate change is possible, provided that proactive actions are taken by both the public and the private sector. Public authorities need to set clear priorities and implement well designed policies. Most importantly, adequate monitoring mechanisms should be set up in order to provide much needed data which can send early warnings to policy makers and the public …

Wear Behavior Of Tini And Tini-Tic Clads Deposited By Tig Surfacing, Masoud Harooni, Morteza Shamanian, Alireza Fadaei Tehrani

Masoud Harooni

This paper deals with the investigation of wear behavior of TiNi and TiNi-TiC clads applied to plain carbon steel by tungsten inert gas (TIG) surfacing process. In this regard, ball milled Ti-Ni and Ti-Ni-C powder mixtures were used as feedstock materials. The clad layers were investigated using X-ray diffractometery (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), hardness measurements and reciprocating wear tests. The results of microhardness measurements indicated that hardness values of TiNi-TiC composites were higher than those of TiNi by approximately 100HV. It was also shown that the wear behavior of TiNi-TiC clads was better than that …

Mitigation Of Pore Generation In Laser Welding Of Magnesium Alloy Az31b In Lap Joint Configuration, Masoud Harooni, Fanrong Kong, Blair Carlson, Radovan Kovacevic

Masoud Harooni

Magnesium, as the lightest structural metal, has been widely used in the automotive and aerospace industries. Porosity is the main issue in the welding of magnesium alloys and can be caused by surface coatings, hydrogen gas, pre-existing porosity, the collapse of an unstable keyhole and vaporization of alloying elements. In this study, the effect of the oxide layer on pore generation in the welding of AZ31B-H24 magnesium alloy is investigated. A fiber laser with a power of up to 4 kW is used to weld samples in a lap joint configuration. Two groups of samples are studied: as received (AR) …

Effects Of Addition Of Copper Particles Of Different Size To Sn-3.5ag Solder, Haseeb Asma

Haseeb ASMA

In this study, copper particles with different sizes 20-30 nm, 3 and 10 mu m were incorporated into Sn-3.5Ag solder paste to form Sn-Ag-Cu composite solder. The Cu particles were added at 0.7 and 3% by paste mixing for 30 min. The composite solder samples were prepared on copper substrate at 240A degrees C for 60 s. Differential scanning calorimetry was conducted to measure the melting point of the composite solder. The wetting angle and microstructure of the composite solder were studied using optical microscope and scanning electron microscope. Micro hardness was measured using a 10 gf load. It was …

Die Attach Properties Of Zn-Al-Mg-Ga Based High-Temperature Lead-Free Solder On Cu Lead-Frame, Haseeb Asma

Haseeb ASMA

Several candidate alloys have been suggested as high-temperature lead-free solder for Si die attachment by different researchers. Among them, Zn-Al based alloys have proper melting range and excellent thermal/electrical properties. In this study, Zn-Al-Mg-Ga solder wire was used to attach Ti/Ni/Ag metallized Si die on Cu lead-frame in an automatic die attach machine. Die attachment was performed in a forming gas environment at temperature ranging from 370 to 400 A degrees C. At the interface with Cu lead-frame, CuZn(4), Cu(5)Zn(8) and CuZn intermetallic compound (IMC) layers were formed. At the interface with Si, Al(3)Ni(2) IMC formed when 200 nm Ag …

Mechanical Team, Brian Badders, Tyler Hill, Alec Redmann, Erik Peterman, Wataru Suzuki, Josh Berk, Jeremy Straub

Jeremy Straub

No abstract provided.

Landscape Management For Sustainable Supplies Of Bioenergy Feedstock And Enhanced Soil Quality, Douglas L. Karlen, David J. Muth Jr.

David J. Muth

Agriculture can simultaneously address global food, feed, fi ber, and energy challenges provided our soil, water, and air resources are not compromised in doing so. As we embark on the 19th Triennial Conference of the International Soil and Tillage Research Organization (ISTRO), I am pleased to proclaim that our members are well poised to lead these endeavors because of our comprehensive understanding of soil, water, agricultural and bio-systems engineering processes. The concept of landscape management, as an approach for integrating multiple bioenergy feedstock sources, including biomass residuals, into current crop production systems, is used as the focal point to show …

Improving Biomass Logistics Cost Within Agronomic Sustainability Constratints And Biomass Quality Targets, Kevin L. Kenney, J. Richard Hess, William A. Smith, David J. Muth Jr.

David J. Muth

Equipment manufacturers have made rapid improvements in biomass harvesting and handling equipment. These improvements have increased transportation and handling efficiencies due to higher biomass densities and reduced losses. Improvements in grinder efficiencies and capacity have reduced biomass grinding costs. Biomass collection efficiencies (the ratio of biomass collected to the amount available in the field) as high as 75% for crop residues and greater than 90% for perennial energy crops have also been demonstrated. However, as collection rates increase, the fraction of entrained soil in the biomass increases, and high biomass residue removal rates can violate agronomic sustainability limits. Advancements in …

Economics Of Residue Harvest: Regional Partnership Evaluation, David W. Archer, David J. Muth Jr., Jacob J. Jacobson, Douglas L. Karlen

David J. Muth

Economic analyses on the viability of corn (Zea mays, L.) stover harvest for bioenergy production have largely been based on simulation modeling. While some studies have utilized field research data, most field-based analyses have included a limited number of sites and a narrow geographic distribution. An Iowa case study is developed illustrating the use of data extracted from a database of geographically distributed field studies for a region-specific economic analysis. The analysis utilizes grain and residue yield and associated management information from two Iowa field research sites that are Sun Grant Regional Partnership locations associated with the Corn Stover Regional …

Ogólnotechniczne Podstawy Biotechnologii Z Elementami Grafiki Inżynierskiej Ćw., Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

Materiały Odstresowujące, Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.