Digital Commons Network^™

Tractor Test 2172: John Deere 8400r E23, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Tractor Test 2175: Claas Xerion 5000 Cvt, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Tractor Test 2174: John Deere 9620rx Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1112 John Deere 6155m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1111 John Deere 6145m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1108 John Deere 6110m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1159 John Deere 6250r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Skintronics: Wireless, Skin-Wearable Electronics For Monitoring Of Electrocardiogram, Matthew B. Piper, Woon-Hong Yeo, Yongkuk Lee

Undergraduate Research Posters

The ECGs I micro-fabricate are designed to be flexible, stretchable and wireless circuits that can be applied to the skin directly. The device is encased in a conformal, silicon-like substrate, that allows the ECG to be attached with the electrodes. Each electrode has been previously measured and verified that it will be correctly placed for an accurate reading. Prototyping this ECG/electrode device allows the user to mount the prototype directly to the patient without having to attach and wire ten other electrodes. This prototype solves the issue that comes about when a doctor, nurse or emergency medical technician must attach …

Module 2: Solar Powered Cricket Lab & Engineering Guest Speaker, Lindsay Snowden

ENERGY Research and Lesson Plans

Students will participate in a Solar Panel Cricket lab to determine which environmental condition would allow for the solar panel to produce the most power. The three conditions are inside, inside with a flashlight, or outside in the sun. The students will complete a correlating lab worksheet. Students will also ask questions and hold discussions with the guest speaker. Students will actively participate while the guest speaker is presenting.

Development Of Guidance Laws For A Reduced Order Dynamic Aircraft Model, Jack W. Brendlinger

Browse all Theses and Dissertations

A set of guidance control laws has been developed for enabling three distinct modes of operation of a reduced order dynamic aircraft model. These include 1) a waypoint following control law, 2) a trajectory tracking control law, and 3) a set of kinematically constrained control laws for reaching a commanded altitude, speed or heading. The formulation of the reduced order model is presented so that the capabilities and limitations of the model are understood, and so that the interface architecture between the controllers and the plant is clearly defined. The controller formulations are then presented, together with sample results. The …

An Automated Controller Design Methodology For Six Degree-Of-Freedom Aircraft Models, Dominic J. Dierker

Browse all Theses and Dissertations

This thesis presents an automated design methodology for development of six degree-of-freedom aircraft controllers. The essential functions required of the controller design are 1) to provide sufficient inner loop compensation to guarantee dynamic stability and acceptable handling qualities over the full flight envelope, and, 2) to enable automated mission following capabilities through implementation of outer loop trackers. A hierarchical control architecture consisting of nested nonlinear dynamic inversion control loops is proposed as a means of achieving these top level objectives. Gain tuning based on an automated linearization methodology is then suggested. Next, an automated optimal control allocation algorithm is tested …

Optimized Endpoint Delivery Via Unmanned Aerial Vehicles, Fuad Gazal

All Graduate Theses, Dissertations, and Other Capstone Projects

Unmanned Aerial Vehicles (UAVs) are remotely piloted aircraft with a range of varying applications. Though early adoption of UAVs focused on military applications, surveillance, photography, and agricultural applications are presently on the rise. This work aims to ascertain how UAVs may be employed to elicit deceased transportation times, increased power efficiency, and improved safety. Resulting in optimized end point delivery. A combination of tools and techniques, involving a mathematical model, UAV simulations, redundant control systems, and custom designed electrical and mechanical components were used towards reaching the goal of a 10-kilogram maximum payload delivered 10 miles under 30 minutes. Two …

The Effects Of Fiber Orientation And Volume Fraction Of Fiber On Mechanical Properties Of Additively Manufactured Composite Material, Suresh Chandra Kuchipudi

All Graduate Theses, Dissertations, and Other Capstone Projects

Additive manufacturing (AM) also known as 3D printing has tremendous advancements in recent days with a vast number of applications in industrial, automotive, architecture, consumer projects, fashion, toys, food, art, etc. Composite materials are widely used in structures with weight as a critical factor especially in aerospace industry. Recently, additive manufacturing technology, a rapidly growing innovative technology, has gained lot of importance in making composite materials. The properties of composite materials depend upon the properties of constituent’s matrix and fiber. There is lot of research on effect of fiber orientation on mechanical properties of composite materials made using conventional manufacturing …

Process Parameter Optimization With Numerical Modelling And Experimentation Design Of Binder Jet Additive Manufacturing, Sairam Vangapally

All Graduate Theses, Dissertations, and Other Capstone Projects

Binder jetting technology is an additive manufacturing technology in which powder materials are binded together layer by layer forming the product from input CAD model. The process involves printing the product layer by layer, curing and sintering. The mechanical properties of 3D printed samples varies based on process parameters, hence there is a need to tune the process parameters for optimal characteristics. Three main parameters namely layer thickness, sintering time and sintering temperature were identified and the study focuses on the effect of parameters on dimensional accuracy and compressive strength of the samples. Full factorial experimental approach was used to …

Size Effect Of Clay Filler Particles On Mechanical Properties Of Pultruded Polymer Composites Under Shear Loading, Jaysimha Reddy Sonti Reddy

All Graduate Theses, Dissertations, and Other Capstone Projects

Polymer composites are finding a range of applications across different fields of engineering. Hence, there is a need to understand the properties of these polymer composites. Mechanical testing can be done to determine the properties but firstly the composite must be manufactured consuming time and money. However, if the properties gained differ from those expected from composite the obtained data is rejected, and a new composite must be manufactured consuming more time and effort.

The micromechanical models play an important role in estimating the properties of the polymer composites. These models estimate the properties of the composite by estimating the …

Enhanced Handheld Engine Ethanol Study, Charindu Kariyawasan Jalath Thanthree

All Graduate Theses, Dissertations, and Other Capstone Projects

This study examined consumer and professional grade handheld engines. Twenty-four consumer grade 50 hour Emissions Determination Period (EDP) trimmers and 24 professional grade 300 hour EDP backpack leaf blowers were run on four different ethanol fuel concentrations; E0, E10, E15, and E20. Six engines of each type were run on each of the fuel blends through their full EDP.

All engines were broken-in and adjusted to manufacturer specifications on E0. Then engines were emissions tested on E0 to provide a baseline and to determine the rich to lean order of the engines. Next, the leanest operating engine received E20 and …

Thermomechanical Fatigue Life Investigation Of An Ultra-Large Mining Dump Truck Tire, Wedam Nyaaba

Doctoral Dissertations

The cost benefits associated with the use of heavy mining machinery in the surface mining industry has led to a surge in the production of ultra-large radial tires with rim diameters in excess of 35 in. These tires experience fatigue failures in operation. The use of reinforcing fillers and processing aids in tire compounds results in the formation of microstructural inhomogeneity in the compounds and may serve as sources of crack initiation in the tire. Abrasive material cutting is another source of cracks in tires used in mining applications. It suffices, then, to assume that every material plane in the …

Optimal Design And Freeform Extrusion Fabrication Of Functionally Gradient Smart Parts, Amir Ghazanfari

Doctoral Dissertations

"An extrusion-based additive manufacturing process, called the Ceramic On-Demand Extrusion (CODE) process, for producing three-dimensional ceramic components with near theoretical density was developed. In this process, an aqueous paste of ceramic particles with a very low binder content (<1 vol%) is extruded through a moving nozzle at room temperature. After a layer is deposited, it is surrounded by oil (to a level just below the top surface of most recent layer) to preclude non-uniform evaporation from the sides. Infrared radiation is then used to partially, and uniformly, dry the just-deposited layer so that the yield stress of the paste increases and the part maintains its shape. The same procedure is repeated for every layer until part fabrication is completed. Sample parts made of alumina and fully stabilized zirconia were produced using this process and their mechanical properties including density, strength, Young's modulus, Weibull modulus, toughness, and hardness were examined. Microstructural evaluation was also performed to measure the grain size, and critical flaw sizes were obtained. The results indicate that the proposed method enables fabrication of geometrically complex parts with superior mechanical properties. Furthermore, several methods were developed to increase the productivity of the CODE process and enable manufacturing of functionally graded materials with an optimum distribution of material composition. As an application of the CODE process, advanced ceramic components with embedded sapphire optical fiber sensors were fabricated and properties of parts and sensors were evaluated using standard test methods"--Abstract, page iv.

Event-Triggering Architectures For Adaptive Control Of Uncertain Dynamical Systems, Ali Talib Oudah Albattat

Doctoral Dissertations

"In this dissertation, new approaches are presented for the design and implementation of networked adaptive control systems to reduce the wireless network utilization while guaranteeing system stability in the presence of system uncertainties. Specifically, the design and analysis of state feedback adaptive control systems over wireless networks using event-triggering control theory is first presented. The state feedback adaptive control results are then generalized to the output feedback case for dynamical systems with unmeasurable state vectors. This event-triggering approach is then adopted for large-scale uncertain dynamical systems. In particular, decentralized and distributed adaptive control methodologies are proposed with reduced wireless network …

Continuous Focusing And Separation Of Microparticles With Acoustic And Magnetic Fields, Ran Zhou

Doctoral Dissertations

"Microfluidics enables a diverse range of manipulations (e.g., focusing, separating, trapping, and enriching) of micrometer-sized objects, and has played an increasingly important role for applications that involve single cell biology and the detection and diagnosis of diseases. In microfluidic devices, methods that are commonly used to manipulate cells or particles include the utilization of hydrodynamic effects and externally applied field gradients that induce forces on cells/particles, such as electrical fields, optical fields, magnetic fields, and acoustic fields.

However, these conventional methods often involve complex designs or strongly depend on the properties of the flow medium or the interaction between the …

Manufacturing Of Advanced Continuous Fiber Reinforced Composites For High Temperature Applications, James Robert Nicholas

Doctoral Dissertations

"New resin systems have enabled composites to be considered as attractive alternatives in structural applications that require material to be stronger, lighter and/or more resilient to environmental effects. The current work is on the development of processes to produce continuous fiber reinforced materials from two state of the art resin systems. Two processes were developed to produce continuous fiber reinforced ceramic materials from a preceramic polymer. The first was a vacuum forming process developed using the out-of-autoclave polymer composite manufacturing technique in conjunction with the polymer infiltration and pyrolysis process to produce ceramic composite material of zirconium diboride-silicon carbide reinforced …

Repair Of Metallic Components Using Hybrid Manufacturing, Renwei Liu

Doctoral Dissertations

"Many high-performance metal parts users extend the service of these damaged parts by employing repair technology. Hybrid manufacturing, which includes additive manufacturing (AM) and subtractive manufacturing, provides greater build capability, better accuracy, and surface finish for component repair. However, most repair processes still rely on manual operations, which are not satisfactory in terms of time, cost, reliability, and accuracy. This dissertation aims to improve the application of hybrid manufacturing for repairing metallic components by addressing the following three research topics. The first research topic is to investigate and develop an efficient best-fit and shape adaption algorithm for automating 3D models' …

Volumetric Error Compensation For 5-Axis Machine Tools, Jennifer Ruth Creamer

Doctoral Dissertations

"This work presents a geometric error compensation method for large 5-axis machine tools. The compensation method presented here uses tool tip measurements recorded throughout the axis space to construct a position-dependent geometric error model that can easily be used for error compensation. The measurements are taken using a laser tracker, permitting rapid error data gathering at most locations in the axis space. First two model types are compared for generating table-based error compensation and experimental results are presented. Table-based compensation is then extended to machine tool controller types with restrictions on the number or combination of compensation tables using an …

Development Of An Excel® Rocket Simulator For Application In Middle School, High-School, And University Stem Education, Melvin Lee Hortman

All Master's Theses

Water rocket activities are one of the most popular STEM activities used in primary, secondary, and higher education yet are void of engineering, though engineering is heavily implied in the STEM acronym. This study investigated the amount of engineering present in water rocket activities, and options for emphasizing engineering more in water rocket activities using an open-platform flight simulator for use by educators to enable students to predict flight parameters of a water rocket they designed, and test those predictions against experimental data. The simulator was constructed in Excel® with many functions, but the function validated in this study was …

Error Mapping Of Build Volume In Selective Laser Melting, Ninad Kulkarni

Masters Theses

“Selective laser melting is one of the commonly used additive manufacturing processes employed for production of functional part. Therefore, quality aspects such as dimensional accuracy have become a point of great interest. Like all of the other additive manufacturing processes selective laser melting process suffers from the issue if having wide range of process parameters making the process control a complex task. Additionally, issues specific to the selective laser melting process such as position dependency of accuracy of the part, makes it difficult to predict the resulting dimensional inconsistencies in the part manufactured by this processes. This research is an …

Processing, Microstructure, And Mechanical Properties Of Zirconium Diboride-Molybdenum Disilicide Ceramics And Dual Composite Architectures, Ryan Joseph Grohsmeyer

Doctoral Dissertations

"This research had two objectives: characterization of processing-microstructure-mechanical property relationships of conventional ZrB₂-MoSi₂ ceramics at room temperature (RT) and 1500⁰C in air, and fabrication of ZrB₂-MoSi₂ dual composite architectures (DCAs) for use near 1500⁰C. Elastic moduli, fracture toughness, and flexure strength were measured at RT and 1500⁰C for 15 ZrB₂-MoSi₂ ceramics hot pressed using fine, medium, or coarse ZrB₂ starting powder with 5-70 vol.% MoSi₂, referred to as FX, MX, and CX respectively where X is the nominal MoSi₂ content. MoSi₂ decomposed during sintering, resulting in …

Additive Manufacturing Of Glass Using A Filament Fed Process, Junjie Luo

Doctoral Dissertations

"There are many scientific and engineering applications of glass including optics, communications, electronics, and hermetic seals, there has been minimal research towards the Additive Manufacturing (AM) of transparent glass parts. The special thermal and optical properties of glasses make them hard to be printed using conventional AM techniques. In this dissertation, two different AM techniques for glass AM were developed, Selective Laser Melting (SLM) and filament fed process.

Semi-transparent parts were printed with SLM process. However, the filament fed process was found to be more robust and promising for printing optically transparent glass parts. Therefore, this dissertation is focused on …

Additive Manufacturing Of Al 4047 And Al 7050 Alloys Using Direct Laser Metal Deposition Process, Amrinder Singh

Wayne State University Dissertations

Additive manufacturing (AM) of metals is finding numerous applications in automotive and aerospace industry. In 21st century, aluminum is second to steel in automotive sector, because of its high strength to weight ratio. In current era, casted components of Al-Si alloy and high strength Al 7xxx series alloys are being used from low load to high load components. The primary study of this research was to achieve the defect free deposition of Al-Si and Al 7050 alloy. Al-Si alloys samples have been manufactured at lab scale using various additive manufacturing processes, but so far there is no literature available to …

Combustion Phasing Through Combustion Ionization In A Caterpillar C7 Compression Ignition Engine, Kamal Ashraf Assaad

Wayne State University Theses

To achieve the goals of best fuel economy, peak power and low soot emissions in military engines it is necessary to control the combustion process. An in-cylinder combustion sensor is required to achieve the goals of controlling the combustion process. Over the last four decades, in-cylinder pressure transducers and ion current sensors have been available for research and development. Most of the effort has focused on the pressure transducer, however up till now a pressure transducer suitable for use in production engines has not been developed yet, because of cost and durability concerns.This work presents the analysis of experimental data …

Study Of Stability And Thermal Conductivity Of Nanoparticles In Propylene Glycol, Sumit Mahajan

All Graduate Theses, Dissertations, and Other Capstone Projects

This thesis studied the effects of gravity induced settling, thermophoresis and Brownian motion on the thermal conductivity of the Aluminum Oxide (Al2O3) nanofluids. The base fluid was propylene glycol. The effects were studied by making three samples with volumetric percentages of 0.2 %, 2% and 3% Al2O3 in propylene glycol. Sets of 22 experiments were conducted over time to understand the behavior of settling. All samples were manually mixed each time the experiment was conducted. A Thermtest Transient Plane Source TPS 500S was used to measure the thermal conductivity. Volumetric percentages and diameters of nanoparticle were chosen so that the …